Hytronik HC419V Manual de usuario

NOTE:the high-frequency output of this sensor is <0.2mW;approximately just 1‰ of the transmission power of a mobile telephone or

the output of a microwave oven.

1.0

User Manual of Microwave Motion Sensor

New advanced version Model No.:HC419V

The sensor works with a main voltage of 120-277VAC 50/60 Hz.

The sensor has a 7-wire electrical interface:

Nx2 (neutral / 120-277VAC)

L (phase/120-277VAC)

L’ (switched phase / output)

SYNC (synchronization interface)

+ (1-10V “+” interface)

- (1-10V “-” interface)

Antenna module

Led indication

Detection area

Hold-time

Daylight threshold

Stand-by period

Stand-by dimming level

Daylight sensor

0-10V

output

Sync

Wiring of 1 sensor controls a group of ballast /driver.

HC419V

MAX.1000w

LED DriverLED Driver LED Driver

<0.2mW

PRODUCT TYPE:

OPERATING VOLTAGE:

HF SYSTEM:

TRANSMISSION POWER:

RATED LOAD:

DETECTION ANGLE:

POWER CONSUMPTION:

DETECTION RANGE:

TIME SETTING:

LIGHT CONTROL:

STAND-BY PERIOD:

STAND-BY DIMMING LEVEL :

MOUNTING:

WORKING TEMPERATURE:

Microwave Motion Sensor

120-277VAC 50Hz/60Hz

5.8GHz CW radar

<0.2mW

277V ~ 1000W(capacitive load)

120V ~ 400W(capacitive load)

30~150℃

<1W

Max. 12 meters in diameter, adjustable

5s~30min.

2~50LUX,disable

0s, 10s-1h, +∞

10% ~ 50%

Indoors,ceiling & walling

-35 ~ +70℃

3rd Floor, block C, complex building, 155#, Bai'gang road south,

Bai'gang village, Xiao Jin Kou town, Huicheng district, Huizhou 516023

Tel:86-752-2772020 F:86-752-2777877

E: [email protected] W:www.hytronik.com

CHINA FACTORY

Room D, 10/f, Tower A, Billion Center, 1 wang Kwong Road,

Kowloon Bay, Kowloon, Hongkong

T: 00852-35197525 F: 00852-30116936

E: [email protected]

HYTRONIK INDUSTRIAL LIMITED

I – 0s

II – 10s

III – 1min

IV – 5min

V – 10min

VI – 30min

VII – 1h

VIII – +∞

This is the time period you would like to keep at the low light output level before it is completely switched off in the long absence

of people.

Note: “0s” means on/off control; “+∞” means 2 steps of dimming control, fixture never switch off.

Stand-by period (corridor function)

10min

30min

5min

1min

10s

+∞

III

VII

VIII

1.1 This sensor is suitable for indoor use, and is also designed for installation Max. 6m in height.

SECTION 2 SETTINGS

Detection Area:

This determines the effective range of the motion detector and is set by DIP switches at the sensor itself, refer to figure.

Note that reducing the sensitivity will also narrow the detection range.

The following settings are available:

Hold time:

This determines the time the fitting remains at 100% level on motion detection and is set with DIP switches at the sensor

itself, refer to figure. The walk test setting is useful when installing the fitting to establish correct operation and range.

The following settings are available:

Daylight sensor:

This setting holds off the 100% light output should there sufficient daylight and is set using DIP switches at the sensor, refer

to figure. The following settings are available:

*In disable mode the lamp(s) will always be on with motion detected and operate at 100% light output, even in bright daylight.

I – 100%

II – 75%

III – 50%

IV – 10%

I – 5S

II – 30S

III – 1min

IV – 5min

V – 10min

VI – 20min

VII – 30min

I – Disable

II – 50Lux

III – 10Lux

IV – 2Lux

50 %

75%

100 %

10%

III

30min

30s

1min

5min

10min

20min

III

VII

50Lux

10Lux

2 Lux

Disable

III

HC419V

MAX.1000w

HC419V

MAX.1000w

Wiring of multiple sensors control the same group of ballast /driver, any sensor is triggered, the luminaries

in the group light up.

LED Driver XLED Driver XLED Driver X

LED Driver Y LED Driver Y LED Driver Y

Do not connect the 1-10v terminals on driver X to Driver Y.

SECTION 4 TROUBLE SHOOTING

YDEMERESUACYDEMERESUACNOITCNUFLAM

The load will not work

gnittestsujdAdetcelesgnitteslortnoc-thgiltcerrocnI

daolecalpeRytluafdaoL

NOhctiwSFFOhctiwssniaM

gnittesenozkcehCenoznoitcetedehtnitnemevomsuounitnoCnosyawlasidaolehT

The load is on without any identifiable

movement

The sensor is not mounted for reliably detecting movement Securely mount enclosure

Movement occurred, but not identified by the sensor

(movement behind wall, movement of small object in

immediate lamp vicinity etc.)

Check zone setting

The load will not work despite movement Rapid movements are being suppressed to minimize

malfunctioning or the detection radius is too small Check zone setting

I – 10%

II – 20%

III – 30%

IV – 50%

This is the dimmed low light output level you would like to have after the hold-time in the absence of people.

Stand-by dimming level

30%

20%

10%

50%

III

SECTION 3 FUNCTIONS

3.1 Zero-cross relay operation

Designed in the software, the sensor switches on/off the load right on the zero-cross point, to ensure the min. current passing through

the relay contact point, and enable the max. load and life-time of the relay.

3.2 Loop-in and loop-out

Double L N terminal makes it easy for wire loop-in and loop-out, saves the cost of terminal block and assembly time.

* Motion sensor overwrites daylight sensor, meanning the daylight sensor starts to check the ambient natural light only when the

lamp is switch off (motion hold-time ellapsed).

* This 1-10v output is isolated, SELV output.

Otros manuales de Accesorios de Hytronik

Hytronik

Hytronik HIM16 Manual de usuario

Hytronik

Hytronik HIM30 Manual de usuario

Hytronik

Hytronik HC005S/BT Guía rápida

Hytronik

Hytronik HC407VDS Manual de usuario

Hytronik

Hytronik HIR21 Guía rápida

Hytronik

Hytronik HMW30 Manual de usuario

Hytronik

Hytronik HBIR30/CA Guía rápida

Hytronik

Hytronik HC005S/I Guía rápida

Hytronik

Hytronik HMW23 Manual de usuario

Hytronik

Hytronik HCD418 Manual de usuario

Hytronik

Hytronik HIR23 Guía rápida

Hytronik

Hytronik HC005S/BT Guía rápida

Hytronik

Hytronik DS05 Guía rápida

Hytronik

Hytronik HBIR29/SV Guía rápida

Hytronik

Hytronik HIM34 Manual de usuario

Hytronik

Hytronik HC419S Manual de usuario

Hytronik

Hytronik HMW32 Manual de usuario

Hytronik

Hytronik DUAL SENSE HIM11 Guía rápida

Hytronik

Hytronik DS05 Manual de usuario

Hytronik

Hytronik HC419VRC/DH Guía rápida

Hytronik

Hytronik Dual Sense HIM15 Manual de usuario

Hytronik

Hytronik HCD418-I Guía rápida

Hytronik

Hytronik HMW12 Guía rápida

Hytronik

Hytronik Dual Sense HIM11 Manual de usuario

Manuales populares de Accesorios de otras marcas

Hillco

Hillco 2810 Manual de usuario

Siemens

Siemens QSA2700D Manual del operador

Contours

Contours ZY024 Manual de usuario

Saivod

Saivod VS621 Manual de usuario

Virtuox

Virtuox VirtuCLEAN 2.0 Manual de usuario

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manual de usuario

Z-Wave

Z-Wave HSD-200Z Manual de usuario

turck

turck FMX-IM-2UPLI63FX Manual de usuario

Decagon Devices

Decagon Devices 10HS Manual de usuario

UPPAbaby

UPPAbaby Cup Holder Manual de usuario

Elko

Elko SmartSensor Leakage Wireless Manual de usuario

Grizzly

Grizzly H8371 Manual de usuario

Panasonic

Panasonic HG-T Series Manual de usuario

IFM Electronic

IFM Electronic Efector 250 Series Guía de referencia

DigiDesign

DigiDesign 888/24 I/O Manual de usuario

PROZIS

PROZIS QUAY Manual de usuario

patagonia

patagonia PSI Vest Manual de usuario

SFC Energy

SFC Energy EFOY GO! Manual de usuario