Hytronik HC019V Manual de usuario

NOTE:the high-frequency output of this sensor is <0.2mW;approximately just 1‰ of the transmission power of a mobile telephone or

the output of a microwave oven.

<0.2mW

800W(capacitive Load)

2~50LUX, disable

STAND-BY PERIOD: 0s, 10s-1h, +

WORKING TEMPERATURE:

∞

STAND-BY DIMMING LEVEL : 10% ~ 50%

Max. 12 meters in diameter, adjustable.

Approx. 0.8W

1.0

Nx2(neutral / 220-240VAC)

L (phase / 220-240VAC)

L’ (switched phase / output)

New advanced version Model No.:HC019V

The sensor works with a main voltage of 220-240VAC 50/60 Hz.100-120VAC version is available

on request.

Antenna module

Led indication

Detection area

Hold-time

Daylight threshold

Stand-by period

Stand-by dimming level

Daylight sensor

0-10V

output

Sync

Wiring of 1 sensor controls a group of ballast /driver.

HC019V

MAX.800w

LED DriverLED Driver LED Driver

<0.2mW

-35 ~ +70℃

SYNC (synchronization interface)

+ (1-10V “+” interface)

- (1-10V “-” interface)

3rd Floor, block C, complex building, 155#, Bai'gang road south,

Bai'gang village, Xiao Jin Kou town, Huicheng district, Huizhou 516023

Tel:86-752-2772020 F:86-752-2777877

E: [email protected] W:www.hytronik.com

CHINA FACTORY

Room D, 10/f, Tower A, Billion Center, 1 wang Kwong Road,

Kowloon Bay, Kowloon, Hongkong

T: 00852-35197525 F: 00852-30116936

E: [email protected]

HYTRONIK INDUSTRIAL LIMITED

I – 0s

II – 10s

III – 1min

IV – 5min

V – 10min

VI – 30min

VII – 1h

VIII – +∞

This is the time period you would like to keep at the low light output level before it is completely switched off in the long absence

of people.

Note: “0s” means on/off control; “+∞” means 2 steps of dimming control, fixture never switch off.

Stand-by period (corridor function)

10min

30min

5min

1min

10s

+∞

I I

III

VII

VIII

1.1 This sensor is suitable for indoor use, and is also designed for installation Max. 6m in height.

SECTION 2 SETTINGS

Detection Area:

This determines the effective range of the motion detector and is set by DIP switches at the sensor itself, refer to figure.

Note that reducing the sensitivity will also narrow the detection range.

The following settings are available:

Hold time:

This determines the time the fitting remains at 100% level on motion detection and is set with DIP switches at the sensor

itself, refer to figure. The walk test setting is useful when installing the fitting to establish correct operation and range.

The following settings are available:

Daylight sensor:

This setting holds off the 100% light output should there sufficient daylight and is set using DIP switches at the sensor, refer

to figure. The following settings are available:

*In disable mode the lamp(s) will always be on with motion detected and operate at 100% light output, even in bright daylight.

I – 100%

II – 75%

III – 50%

IV – 10%

I – 5S

II – 30S

III – 1min

IV – 5min

V – 10min

VI – 20min

VII – 30min

I – Disable

II – 50Lux

III – 10Lux

IV – 2Lux

50 %

75%

100 %

10%

I I

III

I V

30min

30s

1min

5min

10min

20min

I I

III

I V

VII

50Lux

10Lux

2 Lux

Disable

I I

III

HC019V

MAX.800w

HC019V

MAX.800w

Wiring of multiple sensors control the same group of ballast /driver, any sensor is triggered, the luminaries

in the group light up.

LED Driver XLED Driver XLED Driver X

LED Driver Y LED Driver Y LED Driver Y

Do not connect the 1-10v terminals on driver X to Driver Y.

SECTION 4 TROUBLE SHOOTING

YDEMERESUACYDEMERESUACNOITCNUFLAM

The load will not work

gnittestsujdAdetcelesgnitteslortnoc-thgiltcerrocnI

daolecalpeRytluafdaoL

NOhctiwSFFOhctiwssniaM

gnittesenozkcehCenoznoitcetedehtnitnemevomsuounitnoCnosyawlasidaolehT

The load is on without any identifiable

movement

The sensor is not mounted for reliably detecting movement Securely mount enclosure

Movement occurred, but not identified by the sensor

(movement behind wall, movement of small object in

immediate lamp vicinity etc.)

Check zone setting

The load will not work despite movement Rapid movements are being suppressed to minimize

malfunctioning or the detection radius is too small Check zone setting

I – 10%

II – 20%

III – 30%

IV – 50%

This is the dimmed low light output level you would like to have after the hold-time in the absence of people.

Stand-by dimming level

30%

20%

10%

50%

III

SECTION 3 FUNCTIONS

Designed in the software, the sensor switches on/off the load right on the zero-cross point, to ensure the min. current passing through

the relay contact point, and enable the max. load and life-time of the relay.

3.1 Zero-cross relay operation

Double L N terminal makes it easy for wire loop-in and loop-out, saves the cost of terminal block and assembly time.

3.2 Loop-in and loop-out

This 1-10v output is isolated, SELV output.

Motion sensor overwrites daylight sensor, meanning the daylight sensor starts to check the ambient natural light only when the

lamp is switch off (motion hold-time ellapsed).

Otros manuales de Accesorios de Hytronik

Hytronik

Hytronik HMW15 Guía rápida

Hytronik

Hytronik HMW23 Manual de usuario

Hytronik

Hytronik HIM35 Guía rápida

Hytronik

Hytronik DUAL sense HIM11 Guía rápida

Hytronik

Hytronik HIM38/RF Manual de usuario

Hytronik

Hytronik DUAL SENSE HIM11 Guía rápida

Hytronik

Hytronik HMW31 Manual de usuario

Hytronik

Hytronik HIM30 Guía rápida

Hytronik

Hytronik HIR27 Manual de usuario

Hytronik

Hytronik HMW38/RF Manual de usuario

Hytronik

Hytronik HIR23/D2 Guía rápida

Hytronik

Hytronik HC005S/BT Guía rápida

Hytronik

Hytronik HC407VDS Manual de usuario

Hytronik

Hytronik HC005S/BT Guía rápida

Hytronik

Hytronik DS05 Guía rápida

Hytronik

Hytronik HC401SRC/R Manual de usuario

Hytronik

Hytronik HC005S/BT Guía rápida

Hytronik

Hytronik HMW12 Guía rápida

Hytronik

Hytronik HIM31 Guía rápida

Hytronik

Hytronik HMW35 Guía rápida

Hytronik

Hytronik HIM31 Guía rápida

Hytronik

Hytronik HC428V/RF Manual de usuario

Hytronik

Hytronik HC005S/IR Guía rápida

Hytronik

Hytronik HMW38/RF Guía rápida

Manuales populares de Accesorios de otras marcas

Hillco

Hillco 2810 Manual de usuario

Siemens

Siemens QSA2700D Manual del operador

Contours

Contours ZY024 Manual de usuario

Saivod

Saivod VS621 Manual de usuario

Virtuox

Virtuox VirtuCLEAN 2.0 Manual de usuario

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manual de usuario

Z-Wave

Z-Wave HSD-200Z Manual de usuario

turck

turck FMX-IM-2UPLI63FX Manual de usuario

Decagon Devices

Decagon Devices 10HS Manual de usuario

UPPAbaby

UPPAbaby Cup Holder Manual de usuario

Elko

Elko SmartSensor Leakage Wireless Manual de usuario

Grizzly

Grizzly H8371 Manual de usuario

Panasonic

Panasonic HG-T Series Manual de usuario

IFM Electronic

IFM Electronic Efector 250 Series Guía de referencia

DigiDesign

DigiDesign 888/24 I/O Manual de usuario

PROZIS

PROZIS QUAY Manual de usuario

patagonia

patagonia PSI Vest Manual de usuario

SFC Energy

SFC Energy EFOY GO! Manual de usuario