Hytorc LITHIUM II Series Manual de usuario

LITHIUM SERIES® II ELECTRIC TORQUE TOOL

QUICK START GUIDE

. REVIEW SAFETY INSTRUCTIONS . INSPECT TOOL COMPONENTS CLOCKWISE FROM LEFT

. CHARGE, TEST, AND INSTALL BATTERY

. POWERON TOOL . REVIEW CONTROL PANEL AND HOME SCREEN

 Do not get wet.

 Avoid exposure to condensing humidity.

 Do not operate in temperatures above

140° F (60° C).

 Keep vents clear of dust, dirt and debris.

 Do not use in explosive environments.

 Secure tool to prevent from dropping.

 Keep hands clear of reaction pinch points.

 Use handle supplied with tool.

 Use only the battery and charger provided.

 Follow Lithium-Ion Battery Safety

Instructions:

https://library.hytorc.com/posts/3103

. Square Drive

. Reaction Spline

. Planetary Gearbox

. Handle Attachment

. Directional Control

. Cooling Vents

. Control Panel

. USB Micro Port

. Pistol Grip

. Eyelet

. Trigger

. Dual Speed Switch

. Battery

Power-On

Push any button to

power-on the tool.

Power-Off

Push and hold the

center button to

power-off the tool.

Charge indicator flashes while charging,

turns solid green when fully complete

(approximately 90 minutes).

Slide battery onto

tool base until the

release button

snaps tight.

Press test button: a

fully charged battery

should display 4

green lights.

IMPORTANT! 1 2 3 4

1 2

5 6 7

. Angle

. Release

. Status Indicator

. Fastener

. Direction

. Menu - Level

. Right Scroll Button

. Center Select Button

. Left Scroll Button

. Bluetooth

. Torque

Connect charger to power supply and

insert battery.

1 2

. Battery

. Charging Cable

. Power Outlet

. Power Cord

. Power Supply

. Charger

. Charge Indicator

. Tool Base

. Test Button

. Release Button

HYTORC.COM1-800-FOR-HYTORC

LITHIUM SERIES® II ELECTRIC TORQUE TOOL

. BASIC BOLTING SETUP

. CONVENTIONAL BOLTING

9. BOLTING WITH THE HYTORC NUT 10. CARE AND STORAGE

8. BOLTING WITH THE HYTORC WASHER

 Press center button to display Main Menu.

 Press left and right buttons to scroll, press the center button to

select Torque, Snug, Angle, Release or Fastener screen.

 Press the left and right button to adjust, press the center button

to select the value.

 After setting all basic functions, scroll and select Home to return

to the Home Screen.

 Slide reaction arm onto spline,

align set screw with flat,

tighten screw.

 Slide socket onto drive aligning

pin with hole in the square drive.

 Push pin until flush against socket,

secure O-ring.

 Set fastener to RH Right Hand.

 Secure back nut to prevent turning.

 Position socket on nut, brace reaction arm,

pull and hold trigger until successful completion.

 Slide HYTORC Nut driver over

square drive and align set

screw with flat on spline.

 Tighten set screw and challenge to

make sure it is secure.

 Set fastener to HN HYTORC Nut.

 Place tool driver on HYTORC Nut,

pull and hold trigger until successful

completion.

 When not in use, remove the

battery from the tool.

 The LITHIUM SERIES II

Tool should be stored in the

carrying case when not in use.

 Calibrate periodically.

 Contact HYTORC for Service

or Calibration.

 Slide washer driver over square

drive and align thumb screw

with flat on spline.

 Tighten thumb screw and

challenge to make sure it is secure.

 Set fastener to HWR HYTORC Washer

Right Hand.

 Place tool driver on nut, engage lobes

of reaction washer, pull and hold trigger

until successful completion.

Headquarters:

333 Route 17 N., Mahwah, NJ 07430

+1-201-512-9500

Phone:

1-800-FOR-HYTORC

Email:

info@hytorc.com

Online:

hytorc.comPRCSLSTQSG

Otros manuales para LITHIUM II Series

Otros manuales de Herramientas eléctricas de Hytorc

Hytorc

Hytorc Avanti p7 Manual de usuario

Hytorc

Hytorc jGun J-.25 Instrucciones de montaje

Hytorc

Hytorc LITHIUM II Series Instrucciones de montaje

Hytorc

Hytorc Stealth 2 Manual de usuario

Hytorc

Hytorc jGun Series Manual de usuario

Hytorc

Hytorc jGun DIGITAL Instrucciones de montaje

Hytorc

Hytorc Stealth 2 Manual de usuario

Hytorc

Hytorc Lithium BTM-0250 Manual de usuario

Hytorc

Hytorc LITHIUM II Series Manual de usuario

Hytorc

Hytorc XLCT Series Manual de usuario

Hytorc

Hytorc Torque Gun FLASH-5 Guía de inicio rápido

Hytorc

Hytorc MXT-.7 Manual de usuario

Hytorc

Hytorc jGun DIGITAL Manual de usuario

Hytorc

Hytorc Stealth series Guía

Hytorc

Hytorc LION-.25 Manual de usuario

Hytorc

Hytorc BTM-0250-DOC Manual de usuario

Hytorc

Hytorc Lithium BTM-0250 Manual de usuario

Hytorc

Hytorc HY-1XLT Manual de usuario

Hytorc

Hytorc MXT-XLT032011 Guía

Hytorc

Hytorc LITHIUM II Series Instrucciones de montaje

Hytorc

Hytorc XXI series Guía de inicio rápido

Hytorc

Hytorc LION GUN Instrucciones de montaje

Hytorc

Hytorc TORQUE GUN ZGUN-A.75 Manual de usuario

Hytorc

Hytorc jGun Series Manual de usuario

Manuales populares de Herramientas eléctricas de otras marcas

AEG

AEG OMNI-JS Manual de usuario

SIP

SIP 01533 Manual de usuario

Ribimex

Ribimex PRS499 Manual de usuario

3M Fiber Optic Connector Crimp Tool Manual de usuario

Ryobi

Ryobi P524 Manual de usuario

ROJEK

ROJEK FSN 300A Manual de usuario

Kemper

Kemper 1740PRO Manual de usuario

WABCO

WABCO OptiTire Manual de usuario

EINHELL

EINHELL TE-MS 18/210 Li Manual de usuario

Orgapack

Orgapack OR-T 85 Guía rápida

TOUGHCUT

TOUGHCUT Diamond 400 Manual de usuario

Yaros

Yaros PB-3603 Manual de usuario

Fein

Fein BSS 2.0 E Guía de configuración

Baileigh Industrial

Baileigh Industrial SS-2725 Manual de usuario

Milwaukee

Milwaukee 2674-20 Manual de usuario

Fein

Fein BLs 1.6 Manual de usuario

Princess

Princess Electric Multi Sharpener Manual de usuario

FOREDOM

FOREDOM K.1050 Manual