HYOSUNG Comet 650 Manual de usuario
ELECTRICAL SYSTEM
COOLING SYSTEM
GROUP INDEX
GENERAL INFORMATION 1
PERIODIC MAINTENANCE 2
ENGINE 3
FUEL SYSTEM 4
5
6
CHASSIS 7
SERVICING INFORMATION 8
This manual has been prepared on the basis of the
latest specification at the time of publication.
If modification has been made since then,
difference may exist between the content of this
manual and the actual vehicle.
Illustrations in this manual are used to show
the
basic principles of operation and work proce-
dures.
They may not represent the actual vehicle exactly
in detail.
COPYRIGHT HYOSUNG MOTORS & MACHINERY INC. 2003.
HYOSUNG MOTORS & MACHINERY INC.
FOREWORD
This manual contains an introductory description on
HYOSUNG
and procedures for its
inspection/service and overhaul of its main components.
Other information considered as generally known is not
included.
Read GENERAL INFORMATION section to familiarize
yourself with outline of the vehicle and MAINTENANCE
and other sections to use as a guide for proper inspec-
tion and service.
This manual will help you know the vehicle better so
that you can assure your customers of your optimum
and quick service.
WARNING
This manual is intended for those who have
enough knowledge and skills for servicing
HYOSUNG vehicles. Without such knowledge and
skills, you should not attempt servicing by relying
on this manual only.
Instead, please contact your nearby authorized
HYOSUNG motorcycle dealer.
HOW TO USE THIS MANUAL
TO LOCATE WHAT YOU ARE
LOOKING FOR:
1. The text of this manual is divided into sections.
2. As the title of these sections are listed on the previous
page as GROUP INDEX, select the section where you are look-
ing for.
3. Holding the manual as shown at the right will allow you to find
the first page of the section easily.
4. On the first page of each section, its contents are listed. Find
the item and page you need.
COMPONENT PARTS
Example: Front wheel
SYMBOL
Listed in the table below are the symbols indicating instructions and other information necessary for servicing and
meaning associated with them respectively.
Apply THREAD LOCK1324.
Apply or use brake fluid.
Measure in voltage range.
Measure in resistance range.
Measure in current range.
Use special tool.
Use engine coolant.
Torque control required.
Data beside it indicates specified torque.
Apply oil. Use engine oil unless otherwise
specified.
Apply SUPER GREASE
A
.
Apply SILICONE GREASE.
Apply MOLY PASTE.
Apply BOND1215.
Use fork oil.
DEFINITIONSYMBOL DEFINITIONSYMBOL
Apply SUPER GREASE
C
.
NOTE
Difference between photographs and actual motorcycles depends on the markets.
GENERAL INFORMATION
INFORMATION LABELS 1-1
GENERAL PRECAUTIONS 1-1
SERIAL NUMBER LOCATION 1-3
FUEL, OIL AND ENGINE COOLANT RECOMMENDATIONS 1-4
BREAK-IN PROCEDURES 1-6
CYLINDER CLASSIFICATION 1-6
EXTERIOR ILLUSTRATION 1-7
SPECIFICATIONS 1-8
CONTENTS
1
1-1 GENERAL INFORMATION
Please note, however, that the warning and cautions contained in this manual cannot possibly cover all potential
hazards relating to the servicing, or lack of servicing, of the motorcycle. In addition to the WARNING and CAUTION
stated, you must use good judgement and basic mechanical safety principles. If you are unsure about how to perform a
particular service operation, ask a more experienced mechanic for advice.
GENERAL PRECAUTIONS
WARNING / CAUTION / NOTE
Please read this manual and follow its instructions carefully. To emphasize special information, the symbol and
the words WARNING, CAUTION and NOTE have special meanings. Pay special attention to the messages
highlighted by these signal words.
CAUTION
Indicates a potential hazard that could result in vehicle damage.
WARNING
Indicates a potential hazard that could result in death or injury.
NOTE
Indicates special information to make maintenance easier or instructions cleaner.
WARNING
Proper service and repair procedures are important for the safety of the service machanic and the safe-
ty and reliability of the vehicle.
When 2 or more persons work together, pay attention to the safety of each other.
When it is necessary to run the engine indoors, make sure that exhaust gas is forced outdoors.
When working with toxic or flammable materials, make sure that the area you work in is well-ventilat-
ed and that you follow all off the material manufacturers instructions.
Never use gasoline as a cleaning solvent.
To avoid getting burned, do not touch the engine, engine oil or exhaust system during or for a
while after engine operation.
After servicing fuel, oil, exhaust or brake systems, check all lines and fittings related to the system
for leaks.
GENERAL INFORMATION 1-2
WARNING
If parts replacement is necessary, replace the parts with HYOSUNG Genuine Parts or their equivalent.
When removing parts that are to be reused, keep them arranged in an orderly manner so that they may
be reinstalled in the proper order and orientation.
Be sure to use special tools when instructed.
Make sure that all parts used in reassembly are clean, and also lubricated when specified.
When use of a certain type of lubricant, bond, or sealant is specified, be sure to use the specified type.
When removing the battery, disconnect the negative cable first and then positive cable. When
reconnecting the battery, connect the positive cable first and then negative cable, and replace the terminal
cover on the positive terminal.
When performing service to electrical parts, if the service procedures do not require use of
battery power, diconnect the negative cable at the battery.
Tighten cylinder head and case bolts and nuts, beginning with larger diameter and ending with small-
er diameter, from inside to outside diagonally, to the specified tightening torque.
Whenever you remove oil seals, gaskets, packing, O-rings, locking washers, cotter pins, circlips,
and certain other parts as specified, be sure to replace them with new ones. Also, before installing
these new parts, be sure to remove any left over material from the mating surfaces.
Never reuse a circlip. When installing a new circlip, take care not to expand the end gap larger
than required to slip the circlip over the shaft. After installing a circlip, always ensure that it is com-
pletely seated in its groove and securely fitted.
Do not use self-locking nuts a few times over.
Use a torque wrench to tighten fasteners to the torque values when specified. Wipe off grease or
oil if a thread is smeared with them.
After reassembly, check parts for tightness and operation.
WARNING
To protect environment, do not unlawfully dispose of used motor oil and other fluids: batteries, and tires.
To protect Earths natural resouces, properly dispose of used vehicles and parts.
SERIAL NUMBER LOCATION
The frame serial number or V.I.N. (Vehicle Identification Number) is stamped on the steering head tube. The engine seri-
al number is located on the left down of crankcase assembly.
These numbers are required especially for registering the machine and ordering spare parts.
FRAME SERIAL NUMBER
ENGINE SERIAL NUMBER
1-3 GENERAL INFORMATION
FRONT FORK OIL
Use fork oil : TELLUS #32
BRAKE FLUID
Specification and classification (Front brake) : DOT4
(Rear brake) : DOT4
Grade
Over SG
10W/40
Classification system
API
SAE
If an SAE 10W/40 motor oil is not available, select an
alternative according to the following chart.
Use a premium quality 4-stroke motor oil to ensure
longer service life of your motorcycle.
FUEL, OIL AND ENGINE COOLANT RECOMMENDATIONS
FUEL
Gasoline used should be graded 91 octane (Research Method) or higher. An unleaded gasoline type is
recommended.
ENGINE OIL
ENGINE OIL SPECIFICATION
WARNING
Dont mix the unrecommended oil. It could damage the engine.
When refilling the oil tank, dont allow the dust to get inside.
Mop the oil spilt.
Dont put the patch on the cap. It could disturb the oil to be provided and damage the engine.
WARNING
Since the brake system of this motorcycle is filled with a glycol-based brake fluid by the manufacturer, do not
use or mix different types of fluid such as silicone-based and petroleum-based fluid for refilling the sys-
tem, otherwise serious damage will result.
Do not use any brake fluid taken from old or used or unsealed containers.
Never re-use brake fluid left over from a previous servicing, which has been stored for a long period.
GENERAL INFORMATION 1-4
1-5 GENERAL INFORMATION
ENGINE COOLANT
Use an anti-freeze/engine coolant compatible with an aluminum radiator, mixed with distilled water only.
WATER FOR MIXING
Use distilled water only. Water other than distilled water can corrode and clog the aluminum radiator.
ANTI-FREEZE/ENGINE COOLANT
The engine coolant perform as a corrosion and rust inhibitor as well as anti-freeze. Therefore, the engine coolant
should be used at all times even though the atmospheric temperature in your area does not go down to freezing point.
Hyosung recommends the use of HYOSUNG COOLANT anti-freeze/engine coolant. If this is not available, use an
equivalent which is compatible with an aluminum radiator.
LIQUID AMOUNT OF WATER/ENGINE COOLANT
For engine coolant mixture information, refer to cooling system section, page 5-1
CAUTION
Mixing of anti-freeze/engine coolant should be limited to 60%. Mixing beyond it would reduce its
efficiency. If the anti-freeze/engine coolant mixing ratio is below 50%, rust inhabiting performance
is greatly reduced. Be sure to mix it above 50% even though the atmospheric temperature does not
go down to the freezing point.
Tabla de contenidos
Otros manuales de Motocicleta de HYOSUNG
HYOSUNG
HYOSUNG GV125S Manual de usuario
HYOSUNG
HYOSUNG GD250 Manual de usuario
HYOSUNG
HYOSUNG Aquila 250 Manual de usuario
HYOSUNG
HYOSUNG GV250 Ei Manual de usuario
HYOSUNG
HYOSUNG Aquila 650 FI Manual de usuario
HYOSUNG
HYOSUNG GT650SR - PARTS CATALOGUE Manual de instrucciones
HYOSUNG
HYOSUNG GV125 - CATALOGUE Manual de instrucciones
HYOSUNG
HYOSUNG MS3 - CATALOGUE Manual de usuario
HYOSUNG
HYOSUNG Comet650 Manual de usuario
HYOSUNG
HYOSUNG 2010 ST7 Manual de usuario
HYOSUNG
HYOSUNG RT 125 D Manual de usuario
HYOSUNG
HYOSUNG GV 650 EFI Manual de usuario
HYOSUNG
HYOSUNG GT250 REi Manual de usuario
HYOSUNG
HYOSUNG Aquila Manual de usuario
HYOSUNG
HYOSUNG Motorcycle Manual de usuario
HYOSUNG
HYOSUNG Aquila GT250 R Ej Manual de usuario
HYOSUNG
HYOSUNG XRX125sm Manual de usuario
HYOSUNG
HYOSUNG GT650 EURO 3 - CATALOGUE Manual de usuario
HYOSUNG
HYOSUNG GV250 Ei Manual de usuario
HYOSUNG
HYOSUNG RX 125 - Manual de instrucciones
Manuales populares de Motocicleta de otras marcas
APRILIA
APRILIA ETV MILLE CAPONORD - PART1 02-2001 Manual de usuario
Yamaha
Yamaha 2006 YZF-R1V Manual de usuario
KTM
KTM Freeride E-XC 2021 Manual de usuario
Fantic
Fantic Enduro 125 Manual de usuario
Ducati
Ducati Supersport 750 desmodue Manual de usuario
MV Agusta
MV Agusta 2008 F4 312RR 1078 Manual de instrucciones
