Hydralok H19MM Manual de usuario
USER MANUAL
Swaging Machine Manually Operated
H19MM
2
CONTENTS
WARRANTY CONDITIONS.................................................................................................3
DECLARATION OF CONFORMITY ....................................................................................4
SAFETY REGULATIONS....................................................................................................5
TECHNICAL / DIMENSIONAL DATA ..................................................................................6
HANDLING / TRANSPORT.................................................................................................6
PRELIMINARY CHECKS.....................................................................................................6
LIGHTING............................................................................................................................6
ROUTINE MAINTENANCE..................................................................................................6
DESCRIPTION OF THE MACHINE.....................................................................................7
OPERATING INSTRUCTIONS............................................................................................7
MICROMETER SETTING....................................................................................................8
CALIBRATION PROCEDURE.............................................................................................9
SWAGE CHART................................................................................................................11
DIE FITTING INSTRUCTIONS..........................................................................................12
MAINTENANCE AND SERVICE .......................................................................................12
LUBRICATON....................................................................................................................13
SPARE PARTS..................................................................................................................14
OPTIONAL AIR/HYDRAULIC FOOT PUMP (700 BAR.)...................................................15
3
WARRANTY CONDITIONS
1. Note that all machines undergo strict testing before shipment.
2. All machines are warranted against any defects for a period of 12 MONTHS starting
from the date of delivery to the customer. The company reserves the right to require
a copy of the sales invoice.
3. We must verify defects. Therefore, each defective item must be returned to our
address with SHIPPING CHARGES PREPAID. We will return the item with
CARRIAGE FORWARD. ANY DELIVERIES TO OUR COMPANY WITH
CARRIAGE FORWARD WILL BE SENT BACK TO THE SENDER.
4. This warranty covers replacement and repair of any component found to be
defective.
5. Replacements and repairs completed under this warranty cannot extend its 12
months validity.
6. This warranty does not cover any damages caused by deterioration from use.
7. This warranty is not valid for damage resulting from incorrect operation, or use not
in compliance with the machine instructions.
8. This warranty is not valid in case of unauthorised machine modification.
9. This Instruction Manual is also to be considered as a warranty certificate, with
validity commencing from the date indicated on the freight bill.
GENERAL SALES TERMS AND CONDITIONS
For general sales terms and conditions, always refer to the catalogue Technical data -
General sales terms and conditions, page 59.
4
DECLARATION OF CONFORMITY
(according to current EC legislation)
the subscribed: I.M.M. Hydraulics S.p.A.
registered office in: Via Italia 49, 51
66041 ATESSA
VAT and fiscal Code 01427010697
in the person of Marcello Di Campli
declares:
Model: H19MM-M-1
Construction Year:
Serial Number:
Description: Swaging machine, manual pump operated
The machine is not included in the list of the Annex IV of Machinery Directive 2006/42/CE.
The machine complies with the requirements of Machinery Directive 2006/42/CE and to
the following modifications.
Atessa, 26/10/2018 Signed
5
SAFETY REGULATIONS
Always work in safe conditions and with the necessary space around the machine. Ensure
that the machine is placed on a stable and appropriate working surface.
1. DO NOT USE the equipment before reading the user manual.
2. CAUTION! If improperly used, the equipment may be dangerous and may cause
injury. Do not touch any moving parts.
3. CAUTION! It is absolutely essential that all working operations are carried out by
one operator only
4. This manual must be provided for the machine operator. Ensure that the operator is
aware of his/her responsibilities.
5. Guards must never be removed or tampered with.
6. (Where applicable) A fully trained and competent electrician must connect the
machine to the appropriate electricity supply.
7. Always wear protective gloves, safety glasses and appropriate clothing.
8. (Where applicable) Disconnect the power supply before removing any covers, or
attempting any maintenance of the machine
9. Only original spare parts can be used in the maintenance of the machine.
6
TECHNICAL / DIMENSIONAL DATA
TECHNICAL / DIMENSIONAL DATA
H19MM
Capacity
3/16” –3/4” (2 wire)
R1AT, R2AT, 1SN, 2SN
Pressure requirements for optional
air/hydraulic power pack
7.0 bar (100 psi)
Packed Dimensions [mm]
600x400x460
Net weight [kg]
20
Type of operation
Twin speed hand pump
(10.000 psi)
Noise level
< 70 dB
HANDLING / TRANSPORT
The machine will normally be shipped bolted to a wooden pallet. The bolts should be
removed and the machine lifted onto the work place using suitable lifting equipment.
PRELIMINARY CHECKS
Place the machine on a stable surface.
LIGHTING
The equipment does not have its own lighting and so it must be used in a suitably
illuminated area.
ROUTINE MAINTENANCE
Ensure that moving parts are always lightly greased. Where applicable check periodically
that the limit switches and emergency controls are in good working order.
7
DESCRIPTION OF THE MACHINE
Machine for connecting hoses with eight interchangeable segments of clamps.
OPERATING INSTRUCTIONS
Fig.1
The machine is operated by a hand operated hydraulic pump. (Item 1 - Fig.1). When the
release valve (Item 2 - Fig.1) is closed and the pump operated, the swaging head will
close and a hose assembly can be swaged.
To release the finished assembly unscrew the release valve two turns.
To operate the machine, set the micrometer (Item 3 - Fig 1) to the swage size
recommended by the fitting manufacturers. (See Micrometer setting instructions below.)
Close the release valve and operate the pump to close the dies onto the assembly to be
swaged. Ensure the ferrule is within the die length before proceeding.
8
Operate the pump until the indicator rod (Item 4 - Fig.1)is level with the end of the
micrometer adjusting thimble (Item 5 - Fig.1).Swage is now complete. Initial swages
should be checked for swage size.
To remove completed assembly, unscrew the release valve and allow the machine to
open. The machine opening can be stopped by closing the release valve and need not be
fully opened each time, unless the complete opening of the pressing head is necessary to
remove the assembly.
MICROMETER SETTING
To set the machine to swage a fitting whose final swage size 24,10 mm, select the die
set S22 as indicated on the swage chart in page 11. The micrometer must be set to the
difference between the dieset size and the final swage size. In this case:
(24,10) - (22) = 2,10
To set the micrometer to the desired value (2.10), rotate the thimble (Num.1 - Fig.2) until
the line below the value "1", on the thimble, scale is aligned with the center line present on
the scale of the micrometer and the horizontal line corresponding to the value "2" indicated
on the micrometer scale indicator is flush with the thimble ring nut (Num.2 - Fig.2). The
machine is now ready to press to a diameter of 24,10 mm.
Micrometer set at 2.00 mm Micrometer set at 2.10 mm
Fig. 2
9
CALIBRATION PROCEDURE
1. Fit the S28 die set into the machine.
2. Use a mandrel of known size of 30mm.
3. With mandrel in the machine pump until the maximum pressure has been achieved.
4. Set the calibrator to 2.00 on the dial.
5. Turn adjusting screw (Item 4 - Fig.4) at the end of the calibrator rod, until it is level
with the top of the calibrator (Item 1 - Fig.4).
6. To check calibration, release pressure and repeat step 3. At maximum pump
pressure the calibrator rod should be level with the top of the calibrator.
+
=
24,10
Die size: 22
Micrometer = 2,10
Swage size
Fig 3
S22
10
Fig. 4
Tabla de contenidos
Manuales populares de Herramientas de crimpado de otras marcas
Milwaukee
Milwaukee M18 Manual de usuario
HOGERT
HOGERT HT1P169 Manual de usuario
Textron
Textron ESG105L Manual de usuario
Tyco Electronics
Tyco Electronics 90035-3 Manual de usuario
Emerson
Emerson Klauke ES 20RMCCFB Manual de usuario
Continental Refrigerator
Continental Refrigerator PC150HD Manual de usuario