Hybrid+ HMH 12 Manual de usuario
User Manual
Please read the instructions carefully before use
1-
TABLE OF CONTENTS
1. Safety Instructions
2. Technical Specifications
3. Installation
4. How to set up the unit
5. How to control the unit
6. DMX-512 Configuration
7. DMX-512 Connections
8. Troubleshooting
9. Fixture Cleaning
2-
Safety Instructions
WARNING
Please keep this User Manual for future consultation. If you sell the fixture to another
user, be sure that they also receive this instruction booklet.
Unpack and check carefully that there is no transportation damage before using the
fixture.
It’s important to ground the yellow/green conductor to earth in order to avoid electric
shock.
Disconnect main power before servicing and maintenance.
Maximum ambient temperature is Ta : 40℃. Don’t operate it where the temperature is
higher than this.
In the event of a serious operating problem, stop using the fixture immediately. Never
try to repair the fixture by yourself. Repairs carried out by unskilled people can lead to
damage or malfunction. Please contact the nearest authorized technical assistance
center. Always use the same type of spare parts.
Do not connect the device to any dimmer pack.
Do not touch any wire during operation as there might be a hazard of electric shock.
To prevent or reduce the risk of electrical shock or fire, do not expose the fixture to rain
or moisture.
The housing must be replaced if they are visibly damaged.
Do not look directly at the LED light beam while the fixture is on.
There are no user serviceable parts inside the fixture. Do not open the housing or
attempt any repairs by yourself. In the unlikely event your fixture may require service,
please contact your nearest dealer.
Due to the magnifying type lens, please keep the lens out of contact with direct sunlight.
Direct sunlight can cause heat to build up inside of the unit, which will seriously damage
the unit.
Caution
There are no user serviceable parts inside the fixture. Do not open the housing or attempt
any repairs yourself. In the unlikely situation your unit may require service, please contact
your nearest dealer.
Please read the instructions carefully which include important
information about the installation, operation and maintenance.
3-
2. Technical Specifications
Power supply:AC100-240V,50/60Hz
Power consumption:75W
Light source:40W RGBW 4 in 1 LEDs
Effects: 12Pcs RGB 3IN1 SMD 5050 LED
Life Time:50,000 hours
Beam angle:6°
Control panel:4 Digital LED display figures
Control mode: sound activation, auto, master/slave, DMX512
DMX channels:16/30CHS
Pan/Tilt rotation:540°/ 270°, speed adjustable
Packing size: 3
50x 240 x 220 mm
Net Weight: 2.5kg
3. Installation
The unit should be mounted via its screw holes on the bracket. Always ensure that the unit
is firmly fixed to avoid vibration and slipping while operating. Always ensure that the
structure to which you are attaching the unit is secure and is able to support a weight of 10
times the unit’s weight. Also always use a safety cable that can hold 12 times the weight of
the unit when installing the fixture.
The equipment must be fixed by professionals. And it must be fixed at a place where the
unit is out reach.
4-
4. How to set up the unit
Main Function Chart
5-
5. How to control the fixture
There are two ways to control the fixture
A. Universal DMX controller
B. Master/Slave operation
A. Universal DMX controller
The fixture can be set to the DMX address remotely by the universal DMX controller. First,
you need to program two scenes into a chase, then link the fixtures to the universal DMX
controller. When you run the chase, all the fixtures of the chain will be set to the series DMX
address automatically. The fixture uses four channels. Please refer to the following table to
set the address for the first four units.
Channels mode
Unit1
Address
Unit2
Address
Unit3
Address
Unit4
Address
CH16
1
17
33
49
CH30
1
31
61
91
B. Master/Slave operation
The fixture will allow you to link 16 fixtures together and operate without a controller. In
Master/Slave mode, the first fixture will control the others to give an automatic, sound
activated, synchronized light show. This function is good when you want an instant show.
The first fixture’s DMX input cable will have nothing to connect it, and the other fixtures will
be set in slave mode automatically. Their DMX input cables connect the last fixture DMX
output cable (daisy chain). Any fixture can act as a Master or as a Slave
6-
6. DMX512 Configuration
16CH Mode
Function
Value
1
Pan
000-255 Pan 0° ~ 540°
2
Pan Fine
000-255
3
Tilt
000-255 Tilt 0° ~ 270°
4
Tilt Fine
000-255
5
Pan& Tilt Speed
000-255 Pan/Tilt speed from fast to slow
6
Dimmer
000-255 Dimmer 0 ~ 100%
7
Strobe
000-008 No Function
009-255 Strobe slow to fast
8
Red
000-255 Dimmer 0 ~ 100%
9
Green
000-255 Dimmer 0 ~ 100%
10
Blue
000-255 Dimmer 0 ~ 100%
11
White
000-255 Dimmer 0 ~ 100%
12
Dimmer5050
000-255 Dimmer 0 ~ 100%
13
Strobe 5050
000-008 No Function
009-255 Strobe slow to fast
14
5050 chase
000-127 Color Macro
128-255 Color chase
15
5050 chase speed
000-255 Color chase speed slow to fast
16
Special
000-199 No Function
200-209 Reset
210-239 No Function
240-255 Sound Activated
7-
30CH Mode
Function
Value
1
Pan
000-255 Pan 0° ~ 540°
2
Pan Fine
000-255
3
Tilt
000-255 Tilt 0° ~ 270°
4
Tilt Fine
000-255
5
Pan& Tilt Speed
000-255 Pan/Tilt speed from fast to slow
6
Dimmer
000-255 Dimmer 0 ~ 100%
7
Strobe
000-008 No Function
009-255 Strobe slow to fast
8
Red
000-255 Dimmer 0 ~ 100%
9
Green
000-255 Dimmer 0 ~ 100%
10
Blue
000-255 Dimmer 0 ~ 100%
11
White
000-255 Dimmer 0 ~ 100%
6
Dimmer5050
000-255 Dimmer 0 ~ 100%
7
Strobe 5050
000-008 No Function
009-255 Strobe slow to fast
12
5050 R1
000-255 Dimmer 0 ~ 100%
13
5050 G1
000-255 Dimmer 0 ~ 100%
14
5050 B1
000-255 Dimmer 0 ~ 100%
15
5050 R2
000-255 Dimmer 0 ~ 100%
16
5050 G2
000-255 Dimmer 0 ~ 100%
17
5050 B2
000-255 Dimmer 0 ~ 100%
18
5050 R3
000-255 Dimmer 0 ~ 100%
19
5050 G3
000-255 Dimmer 0 ~ 100%
20
5050 B3
000-255 Dimmer 0 ~ 100%
21
5050 R4
000-255 Dimmer 0 ~ 100%
22
5050 G4
000-255 Dimmer 0 ~ 100%
8-
23
5050 B4
000-255 Dimmer 0 ~ 100%
24
5050 R5
000-255 Dimmer 0 ~ 100%
25
5050 G5
000-255 Dimmer 0 ~ 100%
26
5050 B5
000-255 Dimmer 0 ~ 100%
27
5050 R6
000-255 Dimmer 0 ~ 100%
28
5050 G6
000-255 Dimmer 0 ~ 100%
29
5050 B6
000-255 Dimmer 0 ~ 100%
30
Special
000-199 No Function
200-209 Reset
210-239 No Function
240-255 Sound Activated
7. DMX512 Connections
The DMX512 is widely used in intelligent lighting control, with a maximum of 512 channels.
9-
1. Connect the fixture together in a “daisy chain” plug the XLR cable from the output of the
fixture to the input of the next fixture. The cable cannot be branched or split to a “Y”
cable. Inadequate or damaged cables, soldered joints or corroded connectors can
easily distort the signal and shut down the system.
2. The DMX output and input connectors are pass-through to maintain the DMX circuit
when one of the units’ power is disconnected.
3. At last fixture, the DMX cable has to be terminated with a terminator to reduce signal
errors. Solder a 120-ohm 1/4W resistor between pin 2(DMX-) and pin 3(DMX+) into a
3-pin XLR-plug and plug it in the DMX-output of the last fixture.
4. Each lighting fixture needs to have an address set to receive the data sent by the
controller. The address number is between 0-511 (usually 0 & 1 are equal to 1).
5. 3 pin XLR connectors are more popular than 5 pins XLR.
3 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+)
5 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+),
Pin4/5: not used
8. Troubleshooting
The following are a few common problems that may occur during operation. Here are some
suggestions for easy troubleshooting:
A. The fixture does not work, it has no light
1. Check the connection of power and main fuse.
2. Measure the mains power supply’s voltage on the main connector.
Tabla de contenidos
Otros manuales de Equipo de DJ de Hybrid+
Hybrid+
Hybrid+ HSF12.4 Manual de usuario
Hybrid+
Hybrid+ HSS 12.6 Manual de usuario
Hybrid+
Hybrid+ HMH 7 Manual de usuario
Hybrid+
Hybrid+ DMX-384 Manual de usuario
Hybrid+
Hybrid+ HH3000 Manual de usuario
Hybrid+
Hybrid+ HSS COB4B Manual de usuario
Hybrid+
Hybrid+ FOUR BEAM Manual de usuario
Hybrid+
Hybrid+ HMH GOBO Manual de usuario
Hybrid+
Hybrid+ TRIPLE DERBY Manual de usuario
Hybrid+
Hybrid+ HSS 6.4B Manual de usuario
Hybrid+
Hybrid+ HMH 230 Manual de usuario
Hybrid+
Hybrid+ HMN 285 Manual de usuario
Hybrid+
Hybrid+ HMH GOBO II Manual de usuario
Hybrid+
Hybrid+ HSS CW Manual de usuario
Hybrid+
Hybrid+ HMH100B Manual de usuario
Hybrid+
Hybrid+ MUSHROOM Manual de usuario
Hybrid+
Hybrid+ CM3UFX Manual de usuario
Hybrid+
Hybrid+ HS 1500 Manual de usuario
Manuales populares de Equipo de DJ de otras marcas
thomann
thomann Stairville DJ Lase 40-G MK-III Manual de usuario
Eagletone
Eagletone 6 Eyes Flower Manual de usuario
EuroLite
EuroLite FLD-1508 Manual de usuario
Technical Pro
Technical Pro LG8xSEA Manual de usuario
JB Systems
JB Systems Lounge Laser DMX Manual de usuario
Lightmaxx
Lightmaxx Vega Halo 90 Manual de usuario
Elation
Elation FUZE WASH Z350 Manual de usuario
Maverick
Maverick MK3 WASH Manual de usuario
Infinity
Infinity TF-260C7 Fresnel Manual de usuario
Chauvet
Chauvet EVE E-50Z Manual de usuario
Eliminator Lighting
Eliminator Lighting E 138 Manual de usuario
EuroLite
EuroLite Mini Multicolor LED Flashing Light SC Manual de usuario