Hussmann RL Manual de usuario

P/N 0387177_K

PARTS LIST

Item

Quantity Description

RL/RM RLN RLNI

RM/RMF RMN RLNIE RLT

1. 2 2 4 2 Donut Gasket

2. 1 1 2 2 Gasket, 1 x

1/2 x 180 in.

3. 1 1 2 1 Gasket,

1/2 x 1/4 x 180 in.

4. 8 8 14 6 Cap Screw

5/16 -18 x 11/4

5. 8 8 14 6 Split Lock Washers 5/16

6. 1 12 1 Joint Molding

7. 5 5 10 5 Binder Post and Screw

8. 1 12 1 Splice Connector

RL / RM / RMF, RLT

RLN / RMN / RLNI / RLNIE

Joining Instructions

NOTE: Be sure first merchandiser has been leveled

according to the main installation instruction.

Carefully unpack and inspect the joining parts listed

above to verify completeness and that there is no

damage.

1Prepare cases for joining (both sides of

islands) as shown in Figure 1.

A. Remove bumpers, rails, packing materials,

and splashguards from the both cases.

B. Remove shelves (if installed).

C. Remove display racks and pans from

ends to be joined.

D. Remove rear shelf supports.

Splashguard brackets must

be installed before piping or

wiring case.

Figure 1. Prepare Cases

Bumper

Retainer

Splashguard

SIDE VIEW

RLT

Bumper

Retainer

Splashguard

SIDE VIEW

MANUAL- KIT REACH-IN JOINING

HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A.

Reach-in Joining Instructions P/N 0387177_K

PARTS LIST

Item

Quantity Description

RL/RM RLN RLNI

RM/RMF RMN RLNIE RLT

1. 2 2 4 2 Donut Gasket

2. 1 1 2 2 Gasket, 1 x

1/2 x 180 in.

3. 1 1 2 1 Gasket,

1/2 x 1/4 x 180 in.

4. 8 8 14 6 Cap Screw

5/16 -18 x 11/4

5. 8 8 14 6 Split Lock Washers 5/16

6. 1 12 1 Joint Molding

7. 5 5 10 5 Binder Post and Screw

8. 1 12 1 Splice Connector

E. Remove back panels from ends to

be joined by lifting up and out near the

bottom. No tools are necessary. The RLT

models have upper and lower back panels

that must be removed.

F. Remove joint molding from any door

frames that will be joined to another case.

G. RLNI Only: Remove screws and inte-

rior top panel on both sides of the island

case end to be joined (see Figure 1).

RLNI Only

Alignment Pin

RL / RM / RMF

RLN / RMN

and RLNI

RLT

3HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A.

P/N 0387177_K

2Locate and remove the shipping block in the

center of the heat exchanger in the interior

bottom of each case, see Figure 2.

Snap a chalk line on the floor to use as a guide

for positioning the front of the cases in the

line-up. The front base frame should be on the

chalk line.

3Once cases are close to final placement, remove

the shipping braces from the ends to be joined,

see Figure 3. Discard bolts and flat washers

used to hold shipping braces. Bolts are too

long to be used for joining.

RMN

Figure 3. Remove Shipping Braces

Donot use shipping bolts to join cases!

Shipping Brace

Figure 2. Remove Shipping Block

(One From Each Side of Island Models)

Shipping

Block

RLNI / RLNI

HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A.

Reach-in Joining Instructions P/N 0387177_K

4If not already installed make

sure NutRetainers and

Alignment Pins are in place in

the right end frame as shown

in Figure 4A or 4B.

Figure 4A. Verify Nut Retainer Installation

RLT

RL / RM / RMF

and

RLN / RMN

Alignment Pin

5HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A.

P/N 0387177_K

RLNI

HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A.

Reach-in Joining Instructions P/N 0387177_K

5Apply Donut Gasket– 1 in recess around both

left end as shown in Figure 5A, Part 1; 5B or

5C, Part 1, and right end frames as shown in

Figure 5A, Part 2; 5B or 5C, Part 2.

Apply the wider Foam Tape Gasket — 2

around the right end frame as shown in Figure

5A, Part 2, 5B or 5C, Part 2.

Figure 5A, Part 1. Apply Gasket to Left End of

RL/RM/RMF and RLN/RMN

RL / RM / RMF

and

RLN / RMN

Right EndLeft End

PadShoeSealer

1- Donut

2- 1 in x in

3- in x in

Use all three gaskets

When applying an end

assembly.

Left End Case

Right EndLeft End

PadShoeSealer

1- Donut

2- 1 in x in

3- in x in

Use all three gaskets

When applying an end

assembly.

Left End Case

Right End Case

Right EndLeft End

PadShoeSealer

1- Donut

2- 1 in x in

3- in x in

Use all three gaskets

When applying an end

assembly.

7HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A.

P/N 0387177_K

Figure 5A, Part 2. Apply Gaskets to Right End of RL/RM/RMF and RLN/RMN

RL / RM /

RMF

and

RLN / RMN

notes:

1. The perimeter gasket, Item 3,

is required by NSF.

2. Butyl is NOT an acceptable

substitute for donut or foam

gasket.

Right EndLeft End

PadShoeSealer

1- Donut

2- 1 in x in

3- in x in

Use all three gaskets

When applying an end

assembly.

Apply Pad Shoe Sealer first,

then apply the narrower Foam

Tape Gasket — 3 around

the perimeter of the right end

frame outside of the donut

gasket as shown in Figure 5A,

Part 2, 5B or 5C, Part 2.

• Lap gaskets at lower

corners.

• Check that there are no

gaps between gasket and case.

• Do not stretch gasket,

especially around corners.

To make sharp corners,paper

backing can be torn without

removing from gasket.

• Do not butt gaskets; always

lap joints.

• Remove paper backing after

gasket is applied to keep gasket

free of debris.

• Gasket has high tack

adhesive and must be properly

placed the first time.

Right End Case

Overlap

Gasket

Pad Shoe

Sealer

Right EndLeft End

PadShoeSealer

1- Donut

2- 1 in x in

3- in x in

Use all three gaskets

When applying an end

assembly.

ALL MODELS: Apply

gasket between

wipes.

HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A.

Reach-in Joining Instructions P/N 0387177_K

Figure 5A. Apply Gaskets to Left End of RLNI

RLNI

Left End Case

Pad Shoe

Sealer

9HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A.

P/N 0387177_K

1 in. x in.

in. x in.

Figure 5B. Apply Gaskets to Right End of RLNI

RLNI Right End Case

Pad Shoe

Sealer

HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A.

Reach-in Joining Instructions P/N 0387177_K

Figure 5C, Part 1. Apply Gasket to Left End of RLT

PadShoeSealer

Left End

Right End

1- Donut

2- 1 in x in

3- in x in

Use all three gaskets

When applying an end

assembly

Left End Case

PadShoeSealer

Left End

Right End

1- Donut

2- 1 in x in

3- in x in

Use all three gaskets

When applying an end

assembly

Left End Case

Right End Case

Right EndLeft End

PadShoeSealer

1- Donut

2- 1 in x in

3- in x in

Use all three gaskets

When applying an end

assembly.

RLT

Otros manuales para RL

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Congelador de Hussmann

Hussmann

Hussmann FMSS-L Manual de instrucciones

Hussmann

Hussmann ARV-01050 Operation Guía de inicio rápido

Hussmann

Hussmann IMPACT Excel D5XRRIS Manual de instrucciones

Hussmann

Hussmann SM-110 Manual de usuario

Hussmann

Hussmann impact Excel B3XC-LGEP Manual de instrucciones

Hussmann

Hussmann ARV-650S Guía del usuario

Hussmann

Hussmann HBD/BC-142 Manual de usuario

Hussmann

Hussmann IMPACT C2-XEP Manual de instrucciones

Hussmann

Hussmann impact Excel C2X-XGEP Manual de instrucciones

Hussmann

Hussmann impact Excel C2X-XGE Manual de instrucciones

Hussmann

Hussmann RL Manual de usuario

Hussmann

Hussmann DCCG-8 Manual de usuario

Hussmann

Hussmann 10HD Guía rápida

Manuales populares de Congelador de otras marcas

Siemens

Siemens GU..D SERIES Manual de usuario

Omcan

Omcan FR-CN-0155 Manual de usuario

Beko

Beko FNE290E24W Manual de usuario

Electrolux

Electrolux ARCTIS G 8 60 50-6I Manual de usuario

Electrolux

Electrolux EUF2042AOX Manual de usuario

Dometic

Dometic CoolFreeze CFX95DZ Manual de usuario

Electrolux

Electrolux EUF7000W1 Manual de usuario

Polar Electro

Polar Electro CT330 Manual de usuario

MPM

MPM MPM-145-SK Series Manual de usuario

SAF

SAF PRESTOTIG 200AC/DC Guía rápida

Zanussi

Zanussi ZFT11407WA Manual de usuario

AEG

AEG A63190GT Manual de usuario

AEG

AEG A81000TNW0 Manual de usuario

Matsui

Matsui MUC50S15E Manual de usuario

NEFF

NEFF G4344X8 Manual de usuario

Frigidaire

Frigidaire FV 1246 H Manual de usuario

Frigidaire

Frigidaire FFC13K1AW Manual de usuario

Electrolux

Electrolux EU 2400C Manual de usuario