Husqvarna 555 Manual de usuario
User’s Guide
545, 555
KEEPING THE WORLD SEWING
2 Instruction book Lily 555/545
When using an electrical appliance, basic safety precautions should always be follo-
wed, including the following:
Read all instructions before using this household sewing machine
DANGER
- To reduce the risk of electric shock:
• A sewing machine should never be left unattended when plugged in. Always unplug
the sewing machine from the electric outlet immediately after using and before
cleaning.
• Always unplug before relamping. Replace bulb with same type rated 5 Watts.
WARNING
- To reduce the risk of burns, fire, electric shock,
or injury to persons:
• Do not allow to be used as a toy. Close attention is necessary when used by or near
children.
• Use only for its intended use as described in this manual. Use only attachments
recommended by the manufacturer as contained in this manual.
• Never operate this sewing machine if it has a damaged cord or plug, if it is not wor-
king properly, if it has been dropped or damaged, or dropped into water. Return it
to the nearest authorized dealer or service center for examination, repair, electrical
or mechanical adjustment.
• Never operate the sewing machine with any air openings blocked. Keep ventilation
openings of the sewing machine and foot controller free from the accumulation of
lint, dust, and loose cloth.
• Keep fingers away from all moving parts. Special care is required around the sewing
machine needle.
• Always use the proper needle plate. The wrong plate can cause the needle to break.
• Do not use bent needles.
• Do not pull or push the fabric while stitching. It may deflect the needle causing it to
break.
• Switch the sewing machine off (''0'') when making any adjustments in the needle
area, such as threading needle, changing needle, threading bobbin, or changing
presser foot, etc.
• Always unplug the sewing machine from electrical outlet when removing covers,
or when making any other user servicing adjustments mentioned in the instruction
manual. No lubrication by customer is recommended.
• Do not use outdoors.
• Do not operate where aerosol (spray) products are being used or where oxygen is
being administrated.
• To disconnect, turn the switch off (''0'', then remove plug from outlet.
• Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.
SAVE THESE INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
3Instruction book Lily 555/545
Safety instructions 2
Machine parts Model 555 4
Machine parts Model 545 5
Procedures 6-16
Unpacking, Packing away 6
Connecting the foot control 7
Connecting to the power
supply 7
Accessory box, Sewing surface 8
Spool pin 9
Threading the upper thread 10
Threading for twin needles 11
Bobbin winding, Direct
winding 12
Threading lower thread 13
Thread tension, Correct and
incorrect thread tension 14
Presser foot pressure,
Presser foot lever, Changing
the presser foot 15
Changing the needle, Lowering
feed teeth 16
Functions 17-27
Infodisplay 17-19
Stitch selection, Model 555 20
Stitch selection, Model 545 21
Memory 22
Programming 23-26
Mirror image 25
CLR - Deleting programs 26
Satin taper and darning
stitches 27
Maintenance 52
Care of the machine 52
Changing light bulbs 52
List of contents
Sewing 28-51
Automatic buttonholes 28-29
Buttonholes, Buttonhole
knife 30-31
Sewing buttons 32
Straight stitch 33
Needle positions 33
Gathering with straight
stitches 34
Zipper 35
Reinforced straight stitches 36
Stretch stitch, Zigzag 36
Lace edging 37
Three-step zigzag 38
Sewing terry cloth 38
Mending and darning 38
Flatlock 39
Hemming 40
Bridging stitch 41
Seam and Overcast 42
Darning stitch 43
Automatic taper stitch 43
Decorative stitches 44
Quilting, Applique 45
Pictogram 46
Sewing hints 47
Free arm, Jeans hem,
Sewing on belt loops 47
Stitch table, Model 555 48-49
Stitch table, Model 545 50-51
Fault-finding 53-54
Accessories, Needles 55
Index 56-57
4 Instruction book Lily 555/545
Summary Model 555
Summary
1. Door
2. Thread take-up lever
3. Presser foot pressure dial
4. Thread guide
5. Buttonhole sensor socket
6. Light
7. Needle bar
8. Presser foot
9. Free arm
10. Bobbin cover
11. Base plate
12. Drop feed dial
13. Needle plate
14. Presser bar and Presser foot
ankle
15. Needle clamp screw
16. Presser foot lifter
17. Thread tension
18. Thread guide for bobbin
winding
19. Spool pin
20. Spool holders
21. Recess for additional spool
pin
22. Quick-info
23. Thread cutter for bobbin
winding
24. Handwheel
25. Bobbin spindle, Bobbin stop
26. Infodisplay
27. Function selectors
28. Stitch panel
29. Main power switch, Connec-
tion to power supply
1.
2.
3.
4.
8.
9.
7.
6.
5.
10.
11. 12.
19. 20.
29.
17.
16.
15.
14.
13.
18.
28.
27.
26.
25.
24.
23.
22.
21.
5Instruction book Lily 555/545
Summary
18. Thread guide for bobbin
winding
19. Spool pin
20. Spool holders
21. Recess for additional spool
pin
22. Quick-info
23. Thread cutter for bobbin
winding
24. Handwheel
25. Bobbin spindle, Bobbin stop
26. Infodisplay
27. Function selectors
28. Stitch panel
29. Main power switch, Connec-
tion to power supply
Summary Model 545
1. Door
2. Thread take-up lever
3. Presser foot pressure dial
4. Thread guide
5. Buttonhole sensor socket
6. Light
7. Needle bar
8. Presser foot
9. Free arm
10. Bobbin cover
11. Base plate
12. Drop feed dial
13. Needle plate
14. Presser bar and Presser foot
ankle
15. Needle clamp screw
16. Presser foot lifter
17. Thread tension
6.
5.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
19. 20.
28.
29.
27.
26.
25.
24.
23.
22.
21.
7.
18.
4.
3.
2.
1.
6 Instruction book Lily 555/545
1. Place the machine on the table
or cabinet, remove the packaging
and lift off the cover.
2. Remove the side parts of the
packing material, the extension
table, the foot control and finally
the protection cover.
3. The machine is delivered with an
accessory bag, a main cord and a
foot control cord.
4. Wipe the machine, particularly
around the needle and needle
plate to remove any soil before
sewing.
Unpacking
Make sure the extension table is fit-
ted into the right part of the acces-
sory tray and fold the table toward
the machine. Fold down the handle
and replace the cover.
Procedures
1. Unplug the cords from the wall
socket and the machine.
2. Wind the cords around your hand
and place the foot control cord
in the foot control storage space
and the main cord in the pocket
of the cover. There is also space
provided for the instruction book.
3. Check to ensure that all acces-
sories are in the accessory tray.
Slide it onto the machine behind
the free arm.
4. Lower the presser foot.
5. Place the foot control, underside
toward you, on the accessory
tray at the back of the machine,
where also the extension table is
placed.
Packing away after sewing
7Instruction book Lily 555/545
Connecting the foot control
Among the accessories you will find
the foot control cord and the main
cord.
1. Place the foot control on its nar-
row side. Fit the plug into the
socket inside the foot control
compartment.
2. Push it firmly to make sure it is
properly connected. This opera-
tion is only necessary the very
first time you are going to use the
machine.
3. To correctly turn away the cord,
place it into the slot, see picture.
Note: Before plugging in, check to
ensure that the foot control is of
"type FR2".
312
1. Connect the foot control cord to
the first socket on the bottom
right side of the machine.
2. Connect the main cord to the
back socket on the bottom right
side of the machine.
3. When you press the power
switch, both the machine and the
light are switched on.
Procedures
Connecting to the power supply
On the underside of the machine you will find information about the power
supply (V) and the frequency (Hz). Check the power supply setting in the
machine to ensure that this agrees with the main supply before you connect
the machine.
For the USA and Canada
This Sewing Machine has a polarized plug (one blade wider than the other). To
reduce the risk of electric shock, this plug is intended to fit in a polarized outlet only
one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does
not fit, contact a qualified electrician to install the proper outlet. Do not modify the
plug in any way.
8 Instruction book Lily 555/545
Accessory box
1. Open the Accessory box by pla-
cing your finger in the space on
the top and lift upward.
2. In the Accessory box there is a
special tray for presser feet and
bobbins plus space for other ac-
cessories.
3. Store the presser feet and the
bobbins in the tray from the be-
ginning so they are always easily
accessible (refer to the figure).
Extended sewing surface
Procedures
1. Keep the Accessory Tray on the
machine to provide a larger flat
work surface.
2. Slide the Accessory Tray to the
left when you wish to remove it
and use the free arm.
3. To facilitate sewing trouser legs
and sleeve hems use the free arm.
4. To replace the Accessory Tray,
slide it tight onto the machine.
5. The extension table provides an
even larger work surface. To at-
tach the extension table, place the
rear, right corner to the Accessory
Tray and the front, right hook
onto the recess on the free arm.
6. To remove it, push slightly in the
direction of the arrow at the front
right corner, then lift the hook out
of the free arm.
9Instruction book Lily 555/545
d
c
Spool pin
The machine has spool pins suitable
for all types of thread. The main
spool pin (a) is horizontal - the
thread reels off the stationary spool.
Place the spool so that the thread
reels counter-clockwise.
There are two spool holders on
the spool pin. With narrow thread
spools, the small holder (b) is pla-
ced in front of the thread. If you use
large thread spools, the large holder
(c) is placed in front of the thread.
Slide the correct size spool holder
in place so the flat side is pressed
firmly against the spool. No space
between spool holder and spool.
There is also a separate spool pin
(d) to be attached onto the machine.
The fingers on the extra spool pin fit
into the two holes to the right of the
fixed spool pin. Push downward to
snap in place.
The large spool holder (c) is placed
under the thread. This spool pin is
used when winding a bobbin from
a second spool of thread or for a
second spool when sewing with a
twin needle.
Procedures
abc
d
10 Instruction book Lily 555/545
Threading the upper thread
Make sure the presser foot
is raised and the needle is
in the up position
1. Pull the spool pin out.
Place the thread on the
spool pin and the spool
holder on the spool pin
as described. Push the
spool pin back in.
2. Bring the thread in the
direction of the arrow
under the thread guide (a) and
over the thread guide (b).
3. Bring the thread down between
the thread tension discs.
4. Continue threading by drawing
the thread from the right into the
slot on the take-up lever.
5. Thread last guide just above
needle.
6. The needle is threaded from front
to back. The white on the press-
ser foot ankle makes it easy to
see the eye of the needle.
Procedures
7. Place thread under the presser
foot and into the thread knife
where it is cut.
Otros manuales para 555
5
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Máquina de coser de Husqvarna
Husqvarna
Husqvarna VIKING HUSKYLOCK 936 Manual de usuario
Husqvarna
Husqvarna Quilt Designer II Manual de usuario
Husqvarna
Husqvarna VIKING Daisy 315 Manual de usuario
Husqvarna
Husqvarna VIKING Onyx 15 Manual de usuario
Husqvarna
Husqvarna VIKING Amber Air S 600 Manual de usuario
Husqvarna
Husqvarna HUSKYLOCK 900 Manual de usuario
Husqvarna
Husqvarna Viking Epic 3 Manual de usuario
Husqvarna
Husqvarna Classica 100 Manual de usuario
Husqvarna
Husqvarna V. S. Manual
Husqvarna
Husqvarna Viking Platinum Q 160 Manual de usuario
Husqvarna
Husqvarna VIKING Designer EPIC Manual de usuario
Husqvarna
Husqvarna Viking Tribute 150C Manual de usuario
Husqvarna
Husqvarna Viking Platinum MN 1000 Manual de usuario
Husqvarna
Husqvarna Viking 990 Manual de usuario
Husqvarna
Husqvarna Prisma 980 Manual de usuario
Husqvarna
Husqvarna HUSKYLOCK 400 Manual de usuario
Husqvarna
Husqvarna Viking Platinum Q 165 Manual de usuario
Husqvarna
Husqvarna HUSKYLOCK 1002 Manual de usuario
Husqvarna
Husqvarna Zig Zag Manual de usuario
Husqvarna
Husqvarna Eden Rose 250M LIMITED EDITION Manual de usuario
