HunterDouglas Platinum Manual de uso y mantenimiento
for PowerRise®
, PowerGlide®
, PowerTilt™and hard-wired systems
Guide
Remote Control
PLATINUM TECHNOLOGY
Control Like Never Before
INDICATOR
LIGHT
CHANNEL
SELECTOR
UP/DOWN
BUTTON
ALL
GROUPS
BUTTON
GROUP 1
BUTTON
GROUP 2
BUTTON
GROUP 3
BUTTON
GROUP 4
BUTTON
Platinum™Technology utilizes both infrared (IR) and radio
frequency (RF) remote control signals. This guide shows
you how to enjoy optimal performance using the two
methods of operation.
The Hunter Douglas Remote Control
BLINKING GREEN =
PROGRAMMING MODE
SOLID GREEN =
GROUP OPERATING
MODE
SOLID RED =
POINT-AND-PRESS
OPERATING MODE
2 hunterdouglas.com
Getting Started
Using the power of Platinum™Technology is easy. In just
two simple steps, your remote is ready.
POWER UP
Remove the battery
compartment cover on
the back of the remote
control. Insert two AAA
alkaline batteries as
diagrammed inside the
battery compartment.
RESET BUTTON
Use a paper clip to press
and quickly release the
MASTER RESET button
located next to the
batteries. Replace the
battery compartment
cover. You are now
ready to begin.
1
hunterdouglas.com 3
2
PROGRAM
BUTTON
MASTER
RESET
BUTTON
BATTERY
COMPARTMENT
POINT AND PRESS
Point the remote at the satellite eye.
TILT AND TRAVERSE
Move the channel switch to the left
position (channel 1) to tilt the vane.
Move the channel switch to the right
position (channel 2) to traverse the
window covering.
Point-and-Press Operation
PowerRise®and PowerTilt™operating systems
PowerGlide®operating systems
POINT AND PRESS
Point the remote at the receiver eye (either built into the headrail
or on the satellite eye). Press the UP or DOWN button to operate
the window covering.
TILT TRAVERSE
4 hunterdouglas.com
Programming Groups
hunterdouglas.com 5
BEFORE YOU BEGIN
Partially lower or tilt the
window covering.
PROGRAM BUTTON
Use a paper clip to press
and quickly release the
PROGRAM button on the back
of the remote control. The
indicator light at the top of
the remote will blink green for
approximately 30 seconds.
GROUP NUMBER
While the indicator light
is blinking green, press
the GROUP number to
which you are adding the
window covering.
UP BUTTON
Point the remote at the receiver
eye (either built into the headrail
or on a satellite eye) of the
window covering and press the
UP button. The unit will raise or
“jog” to show that it has been
programmed into the remote
control. Repeat steps to program
other window coverings.
1
2
3
Operating Groups
GROUP NUMBER
Press the GROUP number for
the window covering(s) you
wish to operate.
UP OR DOWN
Press the UP or DOWN
button to operate the window
covering(s) programmed to
that group. The remote does
not need to be pointed at the
receiver eye to operate the
window covering(s).
ALL GROUPS BUTTON
To operate all four groups of
window coverings at the same
time, press the ALL button
before pressing the UP or
DOWN button.
6 hunterdouglas.com
1
2
3
Removing Window Coverings from a Group
hunterdouglas.com 7
BEFORE YOU BEGIN
Partially lower or tilt the
window covering(s).
PROGRAM BUTTON
Use a paper clip to press and
quickly release the PROGRAM
button on the back of the remote
control. The indicator light at the
top of the remote will blink green
for approximately 30 seconds.
GROUP NUMBER
While the light is blinking green,
press the GROUP number from
which you are removing the
window covering.
DOWN BUTTON
Point the remote at the receiver
eye of the window covering and
press the DOWN button. The
unit will lower or “jog” to show
that it has been removed.
MASTER RESET BUTTON
To erase all programmed groups,
use a paper clip to press and
quickly release the MASTER
RESET button located next to
the batteries. Replace the
battery compartment cover.
1
2
3
Notes on Programming
© 2007 Hunter Douglas Inc. ® Registered trademark of Hunter Douglas Inc. ™Trademark of Hunter Douglas Inc.
Patented in the U.S. and foreign countries. Other U.S. and foreign patents pending. 5110540027 8/07
ENTERING PROGRAMMING MODE
To activate the programming mode, use a paper clip to press
and quickly release the PROGRAM button located on the back
of the remote control. The programming mode is indicated
by the blinking green indicator light and will stay active for
approximately 30 seconds before timing out.
WINDOW COVERING OPERATION
Window coverings may not be operated while in the programming
mode. Do not operate window coverings when the indicator light
is blinking green.
EXITING PROGRAMMING MODE
To exit the programming mode before it times out, press and
quickly release the PROGRAM button a second time. The indicator
light will stop blinking green. The remote may now be used to
operate your window covering(s).
Refer to the Product Owner’s Guide for further details about
Platinum™Technology.
Tabla de contenidos
Otros manuales de Mando a distancia de HunterDouglas
HunterDouglas
HunterDouglas PowerView Manual de usuario
HunterDouglas
HunterDouglas PowerView Manual de usuario
HunterDouglas
HunterDouglas PowerView Manual de usuario
HunterDouglas
HunterDouglas PowerView Motorization Manual de usuario
HunterDouglas
HunterDouglas PowerView Pebble Manual de usuario
HunterDouglas
HunterDouglas PowerView Pebble Dibujo dimensional
