Hunt Electronic HVR-04 Manual de usuario
HVR-04
Installation Guide
(v 3.1)
FCC Compliance Statement
Caution : Any changes or modifications in construction of this device which are not expressly
approved the party responsible for compliance could void the user's authority to operate the
equipment.
NOTE : This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications, However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
-Consult the dealer or an experienced radio/TV technician for help.
CAUTION
1. Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.
2. Disposal of used batteries according to the general recommendations against the environmental
pollution.
3. Do not throw the batteries into a fire, and do not heat, short-circuit or attempt to disassemble the
batteries.
4. Do not attempt to recharge the batteries.
Important Notice
1. Do not place heavy objects on the top of the HVR-04.
2. HVR-04 is for indoor use. It is not weatherproof. Use HVR-04 with referring to its environmental
specifications (Temperature & Humidity). To clean the HVR-04, gently wipe the outside with a clean dry
cloth.
3. Be sure to use a DC adapter that is provided by Web Gate Inc. Connecting HVR-04 directly to an AC
current will cause electric damages to HVR-04.
4. Be careful not to drop the HVR-04. Physical shocks may harm the product. In addition, be sure the
HVR-04 is secured after installation.
5. HVR-04 is made of metal. Therefore you can hurt human beings if you throw it to them or hit on them.
When installing HVR-04, be cautious to locate on safe places where children are unreachable.
6. If HVR-04 does not operate properly, please contact the closest HUNT ELECTRONIC distributor for
after sales service. Tampering or disassembling the product will void the warranty.
7. Security surveillance laws may differ for each country. Therefore, please contact the local region first
to avoid any surveillance law violations.
Contents
OVERVIEW...................................................................................................................................7
1. What is HVR-04? ..................................................................................................................7
2. Supplied accessories ..........................................................................................................8
3. Description & Function........................................................................................................9
INSTALLATION AND CONNECTION......................................................................................... 11
4. Connecting & Running HVR-04 ........................................................................................ 11
4.1. Connecting camera....................................................................................................... 11
4.2. Connecting monitor.......................................................................................................12
4.3. Connecting audio..........................................................................................................12
4.4. Supplying power ...........................................................................................................13
5. Running OSD menu...........................................................................................................14
5.1. Using menu...................................................................................................................14
5.2. Dialogue box to edit a word..........................................................................................15
6. Setting remote controller ..................................................................................................16
6.1. Setting remote control DIP switch.................................................................................16
6.2. Set ID of HVR-04..........................................................................................................16
6.3. Selecting HVR-04 .........................................................................................................17
6.4. Operable range of remote controller.............................................................................17
6.5. Loading the batteries into remote controller .................................................................18
7. HVR-04 configuration ........................................................................................................19
7.1. Basic configuration........................................................................................................19
7.2. Advanced configuration ................................................................................................19
7.3. External storage & Backup configuration......................................................................20
7.4. Internet/Intranet configuration.......................................................................................20
8. HVR-04 basic setting .........................................................................................................21
8.1. Viewing image...............................................................................................................21
4
8.2. Setting Date & Time......................................................................................................22
8.2.1. Time zone..............................................................................................................22
8.2.2. Daylight saving ......................................................................................................22
8.2.3. Time format............................................................................................................22
8.2.4. Date .......................................................................................................................23
8.2.5. Time.......................................................................................................................23
8.2.6. Apply Date/Time ....................................................................................................23
8.3. Setting recording condition...........................................................................................24
8.3.1. Configuration status...............................................................................................24
8.3.2. Channel status.......................................................................................................25
8.3.3. Recording speed/quality........................................................................................25
8.3.4. Speed(ips)..............................................................................................................25
8.3.5. Quality....................................................................................................................25
8.3.6. Audio recording......................................................................................................25
8.3.7. Apply......................................................................................................................25
9. Connecting and configuring sensor................................................................................26
9.1. Connecting Sensor Input..............................................................................................26
9.2. Setting sensor at OSD menu........................................................................................27
10. Connecting & configuring relay out .............................................................................28
10.1. Connecting relay out .................................................................................................28
10.2. Configuring relay out.................................................................................................29
11. Connecting external device with serial port................................................................30
11.1. Connecting text input device (ATM / POS / Access control).....................................30
12. Connecting & configuring serial ports for Pan/Tilt/Zoom..........................................31
12.1. Connecting serial port...............................................................................................31
12.1.1. Connecting RS232.............................................................................................31
12.1.2. Connecting RS485.............................................................................................31
12.1.3. Connecting RS422.............................................................................................32
12.2. Configuring serial port...............................................................................................33
13. Connecting USB device................................................................................................. 35
14. Connecting external storage.........................................................................................36
14.1. IEEE1394 bay ...........................................................................................................36
5
14.2. Connecting IEEE1394 device ...................................................................................36
14.3. Available HDD...........................................................................................................36
14.4. Registering & Formatting HDD..................................................................................37
15. Network monitoring & managing.................................................................................. 38
15.1. Connecting Ethernet..................................................................................................38
15.2. Configuring HVR-04’s Network information ..............................................................39
16. Using DVR manager.......................................................................................................40
16.1. PC system requirements for running DVR manager.................................................40
16.2. Installing DVR manager............................................................................................40
16.3. Uninstalling DVR manager........................................................................................42
16.4. Configstation .............................................................................................................43
16.5. Monitor ......................................................................................................................43
16.6. Playback....................................................................................................................44
APPENDIX ................................................................................................................................. 45
Appendix #1 Using HDD ........................................................................................................ 46
Appendix #2 Installing and replacing internal HDD............................................................49
Appendix #3 Video Input........................................................................................................54
Appendix #4 Using CD-ROM ................................................................................................. 55
Appendix #5 Specification.....................................................................................................56
6
OVERVIEW
1. What is HVR-04?
The HVR-04 is a 4-Analog, 12-IP channel network digital video recorder. The HVR-04 can record and
display 4 analog video channels and 12 IP video channels simultaneously. Video, Audio, and Text Event-
Logs are digitized and stored on two internal hard-drives. Main features are as follows.
□Expandable up to 16 channels (4 analog video channels + 12 IP video channels)
□1 channel audio recording & playback
□Total 120 ips recording speed (Analogue video 60ips + IP video 60ips)
□Real time monitoring (30ips), IP video 5ips
□Built-in software multiplexer for all 16 live monitoring channels (1 / 4 / 9 / 13 / 16Ch Mode)
□Maximum 4TB storage capacity (IEEE 1394 for external HDD)
□ATM/POS transaction information text recording and search with corresponding video
□4 pairs of sensor inputs and alarm outputs
□Built-in hardware motion detection with search function (64-division comparison)
□Various efficient back-up methods (IEEE 1394(FiWi), USB (V 1.1), Ethernet)
□PTZ Control
□User-friendly color graphic OSD Menu
□Dynamic IP (DHCP, Floating IP) support
□IR remote controller
□Remote Management Software (DVR manager)
□Clearer Image and Night Noise Filtering for better image quality
□Digital Water Mark
7
2. Supplied accessories
Unpack and check all the items as below.
1. HVR-04 (1) 2. DC Power Supply (1)
(110V~220V)
3. AC Power Cord (1)
4. CD-ROM (Including DVR manager) (1)
5. Remote Controller (1)
6. Guide (2)
7. Plug Bracket (1) 8. HDD Fixing Screw (8)
8
3. Description & Function
HVR-04 front
(1) LED
(2) IEEE1394 connecter
(3) Remote controller receiver
(4) USB connecter
(5) Function buttons
(6) Bracket fixing hole for rack mount
9
HVR-04 rear
(7) Power switch
(8) Ethernet connector
(9) BNC connector for Video input
(10) Audio input / output connector
(11) RS232 connecter (9Pin D-Sub)
(12) Terminal block for RS232 & 422/485
(13) Terminal block for Sensor input
(14) Terminal block for Relay output
(15) Video output for MONITOR or VCR
(16) Video input type/impedance select & remote controller switch
(17) IEEE1394 connecter
(18) USB connecter
(19) Power connector (DC12V)
(20) GND
10
Tabla de contenidos
Otros manuales de DVR de Hunt Electronic
Hunt Electronic
Hunt Electronic HVRM-T1600L Manual de usuario
Hunt Electronic
Hunt Electronic HVR-16Q Manual de usuario
Hunt Electronic
Hunt Electronic HVRM-HD400H Manual de usuario
Hunt Electronic
Hunt Electronic HVR-04E Manual de usuario
Hunt Electronic
Hunt Electronic HBD-09EE Manual de usuario
Hunt Electronic
Hunt Electronic HNR-04AF Manual de usuario
Hunt Electronic
Hunt Electronic HHR315-16 Manual de usuario
Hunt Electronic
Hunt Electronic HVR-08 Manual de usuario
Hunt Electronic
Hunt Electronic HVRM-T1600Q Manual de usuario
Hunt Electronic
Hunt Electronic HVRM-S400E Manual de usuario
