Huawei UPS2000-G-6KRTLL Manual de usuario
1
Issue: 01
Date: 2020-08-06
UPS2000-G-6KRTLL
Quick Guide
Copyright © Huawei Technologies Co., Ltd. 2020. All Rights Reserved.
1Overview
UPS Model Represented By Weight Dimensions (H x W x D)
UPS2000
-G-6KRTLL
6 kVA
15 kg
131 mm x
438 mm x 480 mm
(1) LCD
(2) MBS port
(3) BMS ports
(4) RS232 communications
port
(5) RS485 communications ports
(connect to northbound devices)
(6) USB
port
(7) AC input and output
terminals (behind the cover)
(8)
Battery input terminal
(behind the cover)
(9
)
Parallel current equalization
ports
(10
) EPO port
(11
) Parallel communications
ports
(12
) Battery PE terminal
The RS485 ports support only the Modbus RTU protocol. For details, see the Modbus
development guide and Modbus user manual.
2
2Installing a UPS
1. Carefully read the
UPS2000-G-6KRTLL User Manual
prior to installation to get familiar with
product information and safety precautions.
2. Use fully insulated tools during installation and operation.
3. Only engineers certified by the manufacturer or its agent are allowed to install, commission,
and maintain the UPS. Otherwise, personal injury or equipment damage may occur, and the
UPS faults caused are beyond the warranty scope of Huawei.
Rack-Mounting the UPS2000-G
Scenario
1. Reserve a space of 1 U in the middle of four batteries for routing battery power cables.
2. Reserve a space of 5 cm between the battery communications port and the cabinet for
installing a communications cable.
3. Reserve a space of 44 mm between the battery edge and the rack edge for installing
battery power cables.
4. In rack-mounted installation scenarios, the front panels of the UPS and lithium batteries
are not on the same plane.
5. The guide rails for the UPS2000-G-6KRTLL are 592.37 mm to 807.37 mm long, 30 mm
wide, and 87 mm high. The guide rails are scalable and support Huawei M-shaped cabinets.
1. Install mounting brackets on UPS.
UPS mounting ear
dimensions (unit:
mm)
3
2. Install devices from bottom to top, as shown in the figures.
（
1）UPS （2）Lithium batteries
4
3Installing Cables
•Connect UPS AC input and output power cables in the same phase sequence. Connect battery
terminals correctly.
•Before connecting cables to the UPS, ensure that the input, output, and battery circuit breakers
are OFF to prevent operations with power applied.
Installing Cables for a Single UPS
Scenario 1
Wiring Terminal Input (AC INPUT) Output (AC OUTPUT)
External Circuit Breaker 32 A
Earth Leakage Circuit Breaker 100 mA -
Cable Cross-sectional Area 6 mm²
Terminal Type OT-6 mm2-M5 terminal
Torque for Tightening Bolts 2 N·m
1. Install AC input and output power cables.
Installing Power Cables
3.1
5
1. The UPS2000-G-6KRTLL needs to connect to external lithium batteries ESM-48100B1 or
ESM-48150B1. Each UPS supports a maximum of 16 batteries connected in parallel. This
document uses four lithium batteries connected in parallel as an example.
2. When lithium batteries are connected, it is recommended that a DC circuit breaker (150 A 80
V DC circuit breaker for the 6 kVA UPS) be installed between the lithium batteries and the
UPS.
3. Before connecting cables to the UPS, ensure that the battery circuit breakers are OFF to
prevent operations with power applied.
4. If the UPS shares a battery string, the PE bar and battery busbar are configured.
Wiring Terminal Battery (BATT. 48VDC)
External Circuit Breaker 125 A (type D)
Cable Cross-sectional Area 25 mm²
Terminal Type OT-25 mm2-M8 terminal
Torque for Tightening Bolts 7 N·m
2. Install battery cables.
After lithium batteries are connected in parallel, connect signal cables to the BMS ports on
the UPS. Install a build-out resistor at the COM-OUT port on the last lithium battery.
Recommended power cable specifications
（
1）UPS rear view （2）Busbar
Installing battery cables (rack-mounted, front view)
6
Installing Cables for Parallel UPSs
Scenario 2
•Before parallel running, ensure that all output circuit breakers for each UPS are ON.
Otherwise, a UPS fault (error code #72) will occur.
•Batteries must be connected for parallel running.
Installing battery cables (rack-mounted, rear view)
Busbar mounting
hole dimensions
(unit: mm)
7
Two UPSs connected in parallel are used as an example.
（
1）UPS rear view （2）Busbar
Installing battery cables (rack-mounted, front view)
8
Installing battery cables (rack-mounted, rear view)
9
Installing Communications Cables
3.2
1. The USB channel supports a serial data communications protocol between the UPS and a PC.
2. If you connect a DB9 connector to the RS232 port, the UPS can exchange data with the PC
over serial communication.
3. You can use only either USB or RS232.
Install parallel communications cables and parallel current equalization cables. Three UPSs
connected in parallel are used as an example.
(1) Parallel current equalization cables
(2) Parallel communications cables
10
No.
Item
Expected Result
1
Cable routing
Cables are routed properly according to engineering
requirements.
2
Cable connection
All cables are connected securely and correctly, and they are free
of damage. Bolts are tightened to specified torque using a torque
wrench.
3
Cable connection to USB,
network, and other ports
Signal cables to USB, network, and other ports are connected
securely and correctly.
4
Cable labels
Labels are neatly attached to both ends of each cable, and the
information on the labels is concise and legible.
5
Ground cable connection
The UPS ground cable is securely connected to the equipment
room ground bar. Use a
multimeter to measure the resistance
between the UPS ground cable and the equipment room ground
bar. The resistance is less than 0.1 ohm.
6
Spacing between cable
ties
Distances between cable ties are the same, and no burr exists.
7
Operating environment
The inside and outside of the cabinet are free from conductive
dust or other sundries.
Verifying the Installation
4
Operations
5
1. Switch on the external battery circuit breaker (if any).
2. Switch on the external AC input circuit breaker (if any). The UPS enters standby mode.
3. Press and hold SELECT for 1s on a non-setting screen to access the login screen for parameter
settings. The initial password is 123. Enter the correct password to access the UPS setting
mode. On the parameter setting screen, press SELECT to select a parameter, and then press
OFF/ENTER. Set parameters as required.
Default output voltage: 230 V AC; options: 220 V AC, 230 V AC, and 240 V AC
Default output frequency: 50 Hz; options: 50 Hz and 60 Hz
Default battery capacity: 4 (200 Ah), 1 (50 Ah) to 48 (2400 Ah). The value increases by 50 Ah
each time you press SELECT.
Default number of parallel UPSs: 1; value range: 1–4
Setting Key UPS Parameters
5.1
Otros manuales para UPS2000-G-6KRTLL
3
Tabla de contenidos
Otros manuales de Fuente de alimentación de Huawei
Huawei
Huawei UPS5000-H-400K-FT Manual de usuario
Huawei
Huawei FusionPower6000 Manual de usuario
Huawei
Huawei UPS2000 Series Manual de usuario
Huawei
Huawei UPS5000-H-400 kVA Manual de usuario
Huawei
Huawei TP482000B Series Manual de usuario
Huawei
Huawei UPS5000-E-12 Manual de usuario
Huawei
Huawei TP48200A-D17A5-2 Telecom Power Manual de usuario
Huawei
Huawei Telecom Power TP48200A-HT19C3 Manual de usuario
Huawei
Huawei Telecom Power TP48200A-DT19C1 Manual de usuario
Huawei
Huawei UPS2000 Series Manual de usuario
Huawei
Huawei SmartLi 3.0 Manual de usuario
Huawei
Huawei ETP48400-C9A2 Manual de usuario
Huawei
Huawei UPS2000-H-6 kVA Manual de usuario
Huawei
Huawei PowerCube 500 PC500-300H1 Manual de usuario
Huawei
Huawei UPS2000-A-RTL Series Manual de usuario
Huawei
Huawei TP48200A-DX08A1 Manual de usuario
Huawei
Huawei MAP05A1 Manual de usuario
Huawei
Huawei UPS5000-H-800K-NTN Manual de usuario
Huawei
Huawei TP48200A-HT15D3 Manual de usuario
Huawei
Huawei V100R001C50 Hoja de instrucciones
