HP HP 54600B Manual

Errata

Title & Document Type:

Manual Part Number:

Revision Date:

HP References in this Manual

This manual may contain references to HP or Hewlett-Packard. Please note that Hewlett-

Packard's former test and measurement, semiconductor products and chemical analysis

businesses are now part of Agilent Technologies. We have made no changes to this

manual copy. The HP XXXX referred to in this document is now the Agilent XXXX.

For example, model number HP8648A is now model number Agilent 8648A.

About this Manual

We’ve added this manual to the Agilent website in an effort to help you support your

product. This manual provides the best information we could find. It may be incomplete

or contain dated information, and the scan quality may not be ideal. If we find a better

copy in the future, we will add it to the Agilent website.

Support for Your Product

Agilent no longer sells or supports this product. You will find any other available

product information on the Agilent Test & Measurement website:

www.tm.agilent.com

Search for the model number of this product, and the resulting product page will guide

you to any available information. Our service centers may be able to perform calibration

if no repair parts are needed, but no other support from Agilent is available.

User and

Service Guide

Publicationnumber54600-97021

November1997 (pdf version Nov 1998)

For SafetyInformation, Warranties, and Regulatory information,

seethepagesbehind the index.

©Copyright Hewlett-Packard Company 1992,1997

All RightsReserved

HP 54600B, HP54601B,

HP 54602B, and HP 54603B

Oscilloscopes

General-Purpose Oscilloscopes

The HP 54600B-Series Oscilloscopes offer exceptional waveform

viewing and measurements in a small, lightweight package. The

two-channel HP 54600B and HP 54603B are suited for production,

field service, and education applications. The four-channel

HP 54601B is best suited for research and design labs, and

applications involving digital circuit test and troubleshooting. For

higher frequency applications, the HP 54602B provides 150 MHz

bandwidth and triggering up to 250 MHz. Each of these oscilloscopes

gives you:

•60-MHz bandwidth (HP 54603B)

100-MHz bandwidth (HP 54600B and HP 54601B)

150-MHz bandwidth (HP 54602B)

•Automatic setup of the front panel

•Automatic and cursor measurements of frequency, time, and voltage

•Waveform storage

•Save and recall of 16 front-panel setups

•Peak detect

These oscilloscopes are easy to use with familiar controls and high

display update rate, but with none of the viewing problems that are

associated with analog oscilloscopes. A bright, crisp display is

obtained at all sweep speeds and delayed sweep magnifications.

Storage is as simple as pressing a button. Negative time allows the

viewing of events that occur before the trigger event. Cursors and

automatic measurements greatly simplify the analysis of these events.

You can upgrade this oscilloscope for hardcopy or remote control with

the addition of an interface module. Unattended waveform

monitoring and additional waveform math, such as FFT, can be added

with the addition of one of the Measurement/Storage modules.

Bring your scope and PC together with BenchLink software.

BenchLink, which runs under Windows, allows easy transfer of scope

traces and waveform data to your PC for incorporation into

documents or storage.

Accessories supplied

•Two 1.5 meter, 10:1 Probes (HP 10071A)

•Power cord for country of destination

•This User and Service Guide

•Programmer’s Guide with Microsoft Windows Help file, ascii help

file, and sample programs.

Accessories available

•HP 34810B BenchLink/Scope Software for Windows

•HP 54650A HP-IB Interface Module

•HP 54652A Parallel Interface Module

•HP 54654A Operator’s Training Kit

•HP 54655A and HP 54656A Test Automation Modules

•HP 54657A HP-IB Measurement Storage Module

•HP 54659B Serial/Parallel Measurement/Storage Modules

•HP 5041-9409 Carrying Case

•HP 5062-7345 Rackmount Kit

•HP 10070A 1.5 meter, 1:1 Probe

•HP 10100C 50 ΩTermination

iii

Options available

•Option 001 RS-03 Magnetic Interference Shielding Added to CRT

•Option 002 RE-02 Display Shield Added to CRT

•Option 005 Enhanced TV/Video Trigger (HP 54602B only)

•Option 090 Deletes Probes

•Option 101 Accessory Pouch and Front-Panel Cover

•Option 102 Two Additional HP 10071A 10:1 Probes (HP 54602B

only)

•Option 103 Operator’s Training Kit (HP 54654A)

•Option 104 Carrying Case (HP 5041-9409)

•Option 106 BenchLink/Scope Software (HP 34810B)

•Option 1CM Rackmount Kit (HP 5062-7345)

•Power Cords (see the table of Replaceable Parts at the end of

Chapter 4, Service.)

In This Book

This manualistheuser andservice

guidefor the HP 54600B,HP 54601B,

HP 54602B, andHP 54603B

Oscilloscopes, and contains five

chapters.

First TimeUsersChapter 1is a quick

start guide that givesyou a brief overview

of the oscilloscope.

Advanced usersChapter 2 is a seriesof

exercises that guide you through the

operationof theoscilloscope.

TV/Video triggeringChapter 3 shows

how touseenhanced TV/Video triggering

if youhaveOption005installedinyour

oscilloscope.

Service techniciansChapter 4

contains the serviceinformation for the

oscilloscope. There are procedures for

verifying performance, adjusting,

troubleshooting,and replacing assemblies

in the oscilloscope.

Reference informationChapter 5lists

thecharacteristics of the oscilloscope.

The Oscilloscope at a Glance

OperatingYour Oscilloscope

Using Option 005 Enhanced

TV/Video Trigger (HP 54602B)

Service

Performance Characteristics

Glossary

Index

Contents

1 The Oscilloscope at a Glance

To inspect the instrument 1–6

To clean the instrument 1–6

To connect a signal to the oscilloscope 1–7

To display a signal automatically 1–9

To set up the vertical window 1–10

To set up the time base 1–12

To trigger the oscilloscope 1–14

To use roll mode 1–16

2 Operating Your Oscilloscope

To use delayed sweep 2–3

To use storage oscilloscope operation 2–6

To capture a single event 2–8

To capture glitches or narrow pulses 2–10

To trigger on a complex waveform 2–12

To make frequency measurements automatically 2–14

To make time measurements automatically 2–16

To make voltage measurements automatically 2–19

To make cursor measurements 2–22

To view asynchronous noise on a signal 2–26

To reduce the random noise on a signal 2–28

To save or recall traces 2–31

To save or recall front-panel setups 2–32

To reset the instrument setup 2–33

To use the XY display mode 2–34

To analyze video waveforms 2–38

Contents–1

3 Using Option 005 Enhanced TV/Video Trigger (HP 54602B)

To select TV display grid 3–4

To autoscale on a video signal 3–4

To trigger on a specific line of video 3–5

To trigger on all TV line sync pulses 3–7

To trigger on a specific field of the video signal 3–8

To trigger on all fields of the video signal 3–9

To trigger on odd or even fields 3–10

To make cursor measurements 3–12

To use delayed sweep 3–14

To analyze video waveforms with Option 005 3–16

To window in on harmonic distortion using FFT 3–18

To connect to other instruments 3–20

4Service

To return the oscilloscope to Hewlett-Packard 4–4

Verifying Oscilloscope Performance 4–5

To check the output of the DC CALIBRATOR 4–6

To verify voltage measurement accuracy 4–7

To verify bandwidth 4–10

To verify bandwidth (alternate method) 4–12

To verify horizontal ∆t and 1/∆t accuracy 4–16

To verify trigger sensitivity 4–18

To verify Vertical Output on Option 005 4-22

Contents

Contents–2

Adjusting the Oscilloscope 4–27

To adjust the power supply4–28

To performthe self-calibration4–31

To adjust the low-frequency compensation4–33

To adjustthe high-frequency pulse response4–35

To adjust the display4–37

To adjust the Option005 offset (R15)(HP54602B only)4–39

TroubleshootingtheOscilloscope 4–40

To construct your own dummy load 4–41

To check out the oscilloscope4–42

To check the Low Voltage Power Supply4–45

To run the internal self-tests 4–46

To troubleshoot Option 005 (HP 54602B only)4–48

Replacing Parts in the Oscilloscope4–49

To replace anassembly4–50

To removethefan 4–51

To removethefrontpanel4–51

To removethedisplay 4–53

To removethesystem board 4–53

Power supply4–54

Keyboard 4–55

To removethehandle 4–56

To remove the Option 005 board 4–56

To order a replacement part 4–57

Contents

Contents–3

Otros manuales para HP 54600B

Este manual sirve para los siguientes modelos

Tabla de contenidos

Manuales populares de Equipo de prueba de otras marcas

SMART

SMART KANAAD SBT XTREME 3G Series Manual de usuario

Agilent Technologies

Agilent Technologies BERT Serial Manual de usuario

Agilent Technologies

Agilent Technologies N3280A Manual de usuario

Vernier

Vernier Go Direct Voltage Manual de usuario

Lifeloc

Lifeloc R.A.D.A.R. Manual de usuario

Fluke

Fluke T5-600 Instrucciones de funcionamiento e instalación

Mercury

Mercury TSL01 Manual de usuario

MAHA

MAHA MBT Series Manual de usuario

Fuji Electric

Fuji Electric P-61 Manual de usuario

ETC

ETC SealerAtor Manual de usuario

Skyfine

Skyfine ETHYWAY V2 Manual de usuario

Appion

Appion G5 Twin Manual de usuario

PCB Piezotronics

PCB Piezotronics 8159-0112A Manual de usuario

BW Technologies

BW Technologies MicroDock II Manual de usuario

Sun Nuclear

Sun Nuclear 1027 Manual de usuario

Biomark

Biomark HPR LITE READER Manual de usuario

Hioki

Hioki 3169-20 Manual de usuario

Ashcroft

Ashcroft ATE-100 Manual de usuario