HP P5389A - Intel Pentium III-S 1.4 GHz Processor... Manual de usuario

Microsoft Small Business Server 2000

Installation Guide for HP NetServers E60,

E800, LC2000, and HP Server tc3100, and

tc4100

NOTICE: The information in this document was last updated for the HP NetServer Navigator CD-ROM version M.04.05.

If you don't have the M.04.05 version CD-ROM and you're obtaining this document from the HP web site as a reference

to install an operating system, be sure to also check the HP web site for the latest available drivers.

©Copyright Hewlett-Packard Company

January 22, 2002

Table of Contents

Introduction

Requirements

Process Flow ( High Level View )

Installation Planning Sheet

Installation Methods

Automatic Installation – Using the HP Navigator CD

Manual Installation

Creating the Drivers Diskettes

Selecting the Manual Installation Method

Installing Small Business Server 2000

Hardware Status Check

Initialize Hard Drives

Configure Server IP Address

Attach Clients to Network

Domain Controller Setup

Troubleshooting Tips

Tip #1. Upgrading from SBS 4.0 to Small Business Server 2000

Tip #2. Using the Small Business Server 2000 integrated backup utility with the HP

NetServer E 60 bundled tape drive

Tip #3. Upgrading Small Business Server 2000 from Uniprocessor HAL to Multiprocessor

HAL

Tip #4. Small Business Server 2000 Driver Signatures

Tip #5. Upgrading D5013B NIC Drivers for Small Business Server 2000

Tip #6. Installation Fails to Boot after First Reboot

Tip #7. Small Business Server 2000 Recovery Options

Tip #8. Terminal Server Service is only support the NetServer L Series

Frequently Asked Questions

APPENDIX

On-Line Information and Software Sources

Introduction

This document was created by Hewlett-Packard for the purpose of helping you install Microsoft

Small Business Server 2000 on your HP NetServer based on procedures tested by HP. The

objective of this document is to provide the information needed to achieve the following tasks.

· Install Small Business Server 2000 from Diskette or CD-ROM

· Create boot diskettes from CD-ROM

· Configure system as Domain Controller and DNS Server

· Change IP Address

· Provide installation troubleshooting tips and tricks

Before you start installing or upgrading to Small Business Server 2000 check the following

documents and make sure you develop an action plan to complete the installation. Use the

following informational resources to help you.

· read1st.txt (Small Business Server 2000 CD-ROM)

· readme.doc (Small Business Server 2000 CD-ROM)

· Troubleshooting Tips and Tricks at the end of this document.

Requirements

· Microsoft Small Business Server 2000 CD-ROM.

· Target system to be tested with minimum of P166 Processor and 64Meg of RAM (128Meg

Recommended).

· One or more Network Interface Cards (NIC).

· One or more hard drives.

· Latest system BIOS update. (http://www.hp.com)

· Two or more clients for testing purpose. (Optional)

· HP Driver's diskette if installing devices that have no drivers included in the Small Business

Server 2000 CD-ROM. Example: HP NetRAID-4M, HP Fiber Channel adapter (Optional),

etc. (This driver's diskette may contain updated Small Business Server 2000 drivers for HP

components.)

Process Flow ( High Level View )

1. Locate and install optional components.

2. Install Small Business Server 2000 on NetServer as stand alone system.

3. Hardware status check with "Device Manager" tool.

4. Prepare all logical drives and shared directories.

5. Configure IP address as needed.

6. Attach clients to network.

7. Test network link using the ping utility.

8. Domain controller setup.

9. Create shared directories.

10. Verify that all clients can access the shared directories.

11. Perform a file copy test.

Installation Planning Sheet

Complete the following table before you begin the installation process. You will need this

information in order to answer questions that you will be asked during the installation process.

Partition Table: ______________________(List target partitions)

User Name: _________________________

Organization: ________________________

Licensing: ___________________________

Computer Name: ______________________

Admin Password: _____________________

Date Time Zone: ______________________

Workgroup or Domain Name: ______________

Registration Key: ____________________________

Installation Methods

There are several ways of installing Small Business Server 2000. The most popular methods are

listed below. Select a method and go to the appropriate section of this guide to begin. Depending

upon your system and its configuration, it may also be necessary to create a drivers diskette.

1. Automatic Installation – boot from the HP Navigator CD and run the

Configuration/Installation utility. (Supported on all HP NetServer systems.)

2. Manual Installation – do the following:

· Create the HP NetServer Small Business Server 2000 drivers diskettes using the HP

NetServer Navigator CD-ROM.

· Select one of the following methods for installation:

- Create Small Business Server 2000 Setup diskettes. Use those diskettes to begin the

installation. Insert and use the Small Business Server 2000 CD when prompted.

- Boot directly from the Small Business Server 2000 CD to begin the installation.

Automatic Installation – Using the HP Navigator CD

HP recommends that you follow this method to install Small Business Server 2000. This is the

easiest method because it requires less user intervention. Following are the steps to complete the

installation of Small Business Server 2000 using the HP Navigator CD.

1. Boot the system from the HP Navigator CD.

2. From the "NetServer Navigator Select a NOS" screen, select the operating system that you

will be installing. Then, select "Continue".

3. At the main menu, select "Configure the Server".

4. Then select "Guided Setup" and follow the instructions on the screen.

Manual Installation

Creating the Drivers Diskette

Before you begin, use one of the following two methods that can be used to create the drivers

diskette. One method is to create the drivers diskette using a system booted from the Navigator

CD. The other method is to create the drivers diskette using a system that is running Windows

NT, Small Business Server 2000, or Windows 95/98.

Creating the Drivers Diskette at the server after booting from the Navigator CD

1. Boot the system from the Navigator CD.

2. From the "NetServer Navigator Select a NOS" screen, select the operating system that you

will be installing. Then, select "Continue".

3. From the "Diskette Title" window, select the diskette that you want to create and then select

"Create Diskette(s)". Follow the on-screen instructions to create the desired diskette(s).

Create the Drivers Diskette using a system running Windows NT, Small Business Server

2000, or Windows 95/98

1. Insert the Navigator CD in the CD-ROM drive on the Windows-based system.

NOTE: The system's monitor must be set for at least 800 x 600 resolution.

2. Your system should auto-detect the presence of the CD and start the Navigator process. If

your system does not auto-start the Navigator process, start it by executing LAUNCH32.EXE

which can be found at the root level of the Navigator CD.

3. Once the Navigator process has started, select the target HP NetServer system from the drop-

down menu and select "Continue".

4. From the "NetServer Navigator Select a NOS" screen, select the operating system that you

will be installing. Then, select "Continue".

5. At the "NetServer Navigator Main Menu" screen, select "Diskette Library".

6. From the "Diskette Title" window, select the diskette that you want to create and then select

"Create Diskette(s)". Follow the on-screen instructions to create the desired diskette(s).

Selecting the Manual Installation Method

Before using this method of installation, decide whether you want to install Small Business

Server 2000 using Setup Diskettes, or by booting directly from the Small Business Server 2000

CD.

· If you wish to create Setup Diskettes (perhaps because you have other systems that do not

support booting from CD), proceed to the following section "Creating Setup Diskettes."

· If you want to start the setup by booting directly off the Small Business Server 2000 CD

(supported for all NetServers), proceed to the following section "Installing Small Business

Server 2000."

Creating Setup Diskettes

If you opt for starting the Small Business Server 2000 installation from Setup Diskettes, do the

following:

1. You need four blank, formatted diskettes. Label them as listed below:

Small Business Server 2000 Setup Boot.

Small Business Server 2000 Setup Disk #2.

Small Business Server 2000 Setup Disk #3.

Small Business Server 2000 Setup Disk#4

2. Place the Small Business Server 2000 CD on a system running Windows NT or Windows 95

or 98.

3. Open a command prompt and change to the d:\bootdisk directory (assuming that D: is your

CD-ROM drive).

4. At the command prompt type:

makebt a: (If using a DOS or a Windows 95 or 98 system)

makebt32 a: (If using an NT system)

5. Follow the on-screen instructions provided by the utility.

Starting the Installation Small Business Server 2000 Using Setup Diskettes

1. Boot from the "Small Business Server 2000 Setup Boot" diskette. Follow instructions

displayed, replacing diskettes as necessary.

2. When prompted for the Small Business Server 2000 CD-ROM, place the CD in the drive and

then proceed to Step 2 in the next section "Installing Small Business Server 2000" to

continue the installation.

Installing Small Business Server 2000

1. If you have opted not to use Setup Diskettes, place the Small Business Server 2000 CD in the

CD-ROM drive. Power off and on to reboot the system. You will see a message that reads

"Setup is inspecting your hardware configuration.". Then the setup screen will be displayed.

NOTE: If you experience any hang or issue during this time, consult the Tips/Tricks

section of this document for help.

2. If you have new drivers to add then press F6 to add OEM SCSI, DAC. Read the message

that shows at the bottom of the display indicating when to press F6.

NOTE: If the boot device driver is not included on the Small Business Server 2000 CD-

ROM, for example the "HP NetRAID-4M", then do the following steps after pressing F6

a) Press Sto select additional hardware.

b) Select Other and press Enter.

c) When prompted to insert driver diskette, please insert the target adapter driver's

diskette created with the HP Navigator CD-ROM. Press Enter to continue.

d) Select the target device driver from the list provided on the display. For example, if

you have the "HP NetRAID-4M", select "Hewlett Packard NetRAID-4M RAID

CONTROLLER".

e) If you have no other drivers that you need to install, press Enter to continue with the

installation.

3. Press Enter to continue at the "Small Business Server 2000 Server Setup. Setup

Notification…" screen.

4. Press Enter to continue at the "Small Business Server 2000 Server Setup. Welcome to

Setup…" screen.

5. Press Cto continue Setup at the "Setup has determined that your computer's startup hard disk

is new…" prompt.

6. Press F8 to accept the licensing agreement.

7. At the drives partitioning screen, select the target drive. If you want to use the entire drive to

install Small Business Server 2000 then press Enter. Otherwise, press Cto create a drive a

partition.

(In this example we will create a 2GB partition. Please note that Small Business Server 2000

does not have the 2GB partition size limitation present on NT 4.0.)

8. Type 2048 and press Enter at the Create partition size prompt.

9. HP recommends that you create all the partitions needed for each hard drive present on your

system at this time.

10. Select the target drive to be used to install Small Business Server 2000. Press Enter.

11. Select Format the partition using the NTFS file system and press Enter.

12. The installer will format and copy files to the hard drive. The system will then reboot.

13. Click Next to continue at the Setup Wizard first dialog box.

14. The Installing Devices screen will be shown with a progress bar on the display. This may

take 10 to 15 minutes.

15. Note: If you see a dialog box titled "Digital Signature Not Found".

Please click "Yes" to continue the installation and read Tip #4 in the troubleshooting section

of this guide.

16. Click Next at the regional Settings screen.

17. At the Personalize Your Software screen, enter a name and organization. Then click Next.

18. Enter the product license key.

19. At the Computer Name and Administrator Password type in your computer name,

administrator password and password confirmation. Then click Next.

20. Click Next at the Small Business Server 2000 Component screen to accept default values.

21. Enter the proper date and time and click Next .

22. The Networking Setting screen starts with a progress bar chart.

23. Click Next to accept the default Typical settings.

24. The Installing Components screen starts with a progress bar chart. It takes about 20 minutes

to complete this section. The wizard will then start the "Performing Final Tasks" section to

complete the installation.

25. Click Finish to complete the installation. Remove the CD from the drive. The system will

then reboot from the hard drive.

NOTE: There may be a period of time with no apparent activity after it displays a

message that reads "OS Loader Version 5.0". Be patient.

26. Follow screen instructions to logon. Enter user-id and password.

27. Click "CANCEL" to close the "Setup needs the location of the Small Business server

2000 Setup files…".

28. Small Business server 2000 has been installed successfully, additional applications can now

be added.

29. Read Tip #7 to install the Small Business Server 2000 Recovery Console to enhance the

system's configuration.

Hardware Status Check

In this section you will run the "Device Manager" tool to identify any issues with the installed

devices or resource conflicts.

1. Right click My Computer.

2. Click Properties. This brings up the "System Properties" panel.

3. Click the Hardware tab.

4. Click the Device Manager… button.

5. Verify that no devices have either a yellow band (!) or question mark (?) symbol next to it.

(See following note for pointer to exceptions)

Yellow (!) means that there is a resource issue with the device.

Question (?) means that the device is unknown.

6. If no (!) or (?) symbols are reported then you are done. Go to step 9. Otherwise, do the next

step.

7. Double click on each of the devices with (!) or (?). Note the "Device Status" message. Or if

a printer is available, use the View, Print from the menu to get a report.

8. See table 5 to verify any errors detected in steps 6 and 7.

9. Verify if the installed drivers are digitally signed.

A. In the Device Manager, click on the device (e.g HP NETRAID 1M/2M) that want to

verify.

B. Right click on that device.

C. Click Properties option.

D. Click on Driver Tab

E. Locate the"Digital Signer:" If the driver of that device is digitally signed then it will

display "MS Windows 2000 Publisher" or "Microsoft Windows Hardware

Compatibility Publisher"

If the driver of the device is not digitally signed we recommend that you check the HP

Website http://www.hp.com/. for the latest driver package. If available, install the new driver.

10. Check the Event viewer to make sure that there are no errors in the log.

Click on Start | Programs | Administrative tools | Event viewer.

NOTE: A warning message with source "DHCP" and errors with sources "W3SVC" and

"SMTPSVC" may appear in the "System Log" of Event Viewer. These warning and

errors will go away after configure all IP addresses for all Ethernet adapters.

11. Exit event viewer.

Initialize Hard Drives

To start the disk administrator use the following procedure.

1. Click Start | Programs | Administrative Tools | Computer Management.

2. If necessary click the +sign next to Storage to open this folder.

3. Double click Disk Management.

4. The "Write signature and Upgrade" wizard will start if you have new hard drives with no

signatures on them.

5. Follow the instructions provided by the wizard to create the new hard drive signature.

6. Perform formatting and partitioning.

NOTE: There are two types of hard drive configuration: Dynamic and Basic. You can

select the appropriate type by right clicking on the drive icon on the screen. Dynamic

drives are used to create volumes which can contain more than one physical hard drive.

Basic drives are used to create primary or local partitioned drives.

Configure Server IP Address

During the installation process the system was configured to use DHCP. Also, when no DHCP

server is found on the network the system will auto-configure a random IP address to start

functioning. It is important that you configure the proper IP address to be able to communicate

with the clients.

Configuring IP Address Steps.

1. Right click My Network Places.

2. Click Properties.

3. Double click Local Area Connection. There is one "Local Area Connection" icon for each

Network Interface Card (NIC) present on the system. Identify the proper NIC by browsing

each one.

4. Click Properties at the Local Area Connection Status screen.

5. Click Internet Protocol(TCP/IP).

6. Click Properties.

7. Click Use the following IP address.

8. Enter appropriate IP address selected on the planning section listed above. For example

100.100.100.1.

9. Click the OK button to continue.

Otros manuales para P5389A - Intel Pentium III-S 1.4 GHz Processor...

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Servidor de HP

HP D7171A - NetServer - LPr Manual de operación y mantenimiento

HP ProLiant ML350e Gen8 Manual de usuario

HP ML350 - ProLiant - G2 Manual de usuario

HP 345646-001 - StorageWorks NAS 2000s External Storage... Manual de usuario

HP Compaq t5515 Manual de servicio

HP t5300 - Thin Client Manual de usuario

HP ProLiant DL380p Generation8 Instrucciones de uso

HP ProLiant BL465c Generation 7 (G7) Instrucciones de uso

HP ProLiant DL560 Gen11 Manual de usuario

HP ProLiant DL320e Instrucciones de uso

HP ProLiant DL165 Instrucciones de uso

HP 2533t - Compaq Mobile Thin Client Hoja de información del producto

HP ProLiant ML310 Generation 5p Manual de usuario

HP ProLiant DL980 G7 Cómo utilizar

HP A4500A - VMEbus Single Board Computer 744... Manual de usuario

HP t510 Manual de operación y mantenimiento

HP Integrity rx4640 Manual de usuario

HP ProLiant ML350p Manual de usuario

HP ProLiant BL660c Gen 9 Instrucciones de instalación

HP Cluster Platform Introduction v2010 Manual de referencia

HP DL320 - ProLiant - G3 Instrucciones de uso

HP Integrity BL870c Manual de usuario

HP D7171A - NetServer - LPr Manual de usuario

HP Blade bc1000 Manual

Manuales populares de Servidor de otras marcas

Dell

Dell PowerEdge R410 Manual de usuario

PowerNAS

PowerNAS CMA Manual de usuario

Supero

Supero FatTwin F617R3-FT Manual de usuario

MSI

MSI P1-109N-L70 Manual de usuario

Dell

Dell PowerEdge XE9640 Manual

Dell

Dell PS4100 Instrucciones de montaje

EtroVISION

EtroVISION EV3151 Manual de usuario

NEC

NEC Express5800/T110j Manual de usuario

Compaq

Compaq ProLiant 3000 Manual

Dell

Dell PowerEdge 3YPMN Manual de usuario

iRobo

iRobo IPC2U Manual de usuario

Nortel

Nortel 1000 Con?guration guide Manual de usuario

Asus

Asus AP7500 Manual de operación y mantenimiento

Avid Technology

Avid Technology AirSpeed 5000 Manual de usuario

Milestone

Milestone Husky IVO 350T Manual de usuario

Planet

Planet NAS-7410 Manual de usuario

Lenovo

Lenovo ThinkSystem SR635 V3 Manual de usuario

Dell

Dell PowerEdge HS5610 Manual