HP NetServer LH 3r Manual de usuario
HP NetServer LH 3r
Installation Guide
for
Compaq®4000/7000 Racks
HP Part Number 5967-5208
Printed in July 1998
ii
Notice
The information contained in this document is subject to change without notice.
Hewlett-Packard makes no warranty of any kind with regard to this
material, including, but not limited to, the implied warranties of
merchantability and fitness for a particular purpose. Hewlett-Packard shall
not be liable for errors contained herein or for incidental or consequential
damages in connection with the furnishing, performance, or use of this material.
Hewlett-Packard assumes no responsibility for the use or reliability of its software
on equipment that is not furnished by Hewlett-Packard.
This document contains proprietary information that is protected by copyright.
All rights are reserved. No part of this document may be photocopied,
reproduced, or translated to another language without the prior written consent of
Hewlett-Packard Company.
Compaq is a registered trademark of Compaq Computer Corporation.
APC is a registered trademark of American Power Conversion Corp.
Hewlett-Packard Company
Network Server Division
Technical Marketing / MS 49EU-FQ
5301 Stevens Creek Boulevard
P.O. Box 58059
Santa Clara, CA 95052-8059 USA
© Copyright 1998, Hewlett-Packard Company.
Audience Assumptions
The user guide is for the person who installs, administers, and troubleshoots
network servers. Hewlett-Packard Company assumes you are qualified in the
servicing of computer equipment and trained in recognizing hazards in products
with hazardous energy levels.
iii
Contents
1 Introduction ................................................................................................. 1
HP NetServer LH 3r – Compaq Rack Precautions......................................... 4
2 Overview ...................................................................................................... 5
3 Installation ................................................................................................... 7
Preparation.................................................................................................... 7
Marking the Installation Holes.................................................................... 7
Installing the Bar Nuts, Screws, and Rack Nuts......................................... 9
Mounting the Slides................................................................................. 10
Installing the NetServer............................................................................... 11
Installing the Recessed Mounting Brackets.................................................. 14
4 Warranty and Support............................................................................... 17
HP Repair and Telephone Support.............................................................. 18
Index............................................................................................................... 19
1
1 Introduction
This document describes how to mount an HP NetServer LH 3r into a Compaq®
model 4000- or 7000-series rack enclosure. Refer to the HP NetServer LH 3r
Road Map and the HP NetServer LH 3/3r User Guide that came with the
NetServer for instructions on adding accessories to and configuring the
NetServer.
The HP NetServer LH 3 (the pedestal version of this NetServer) cannot be
installed in a rack enclosure. If you want to convert an LH 3 to an LH 3r for
installation in a rack enclosure, contact your HP Reseller for information about
the available conversion kit (HP NetServer LH 3 Pedestal-to-Rack Conversion
Kit). The HP NetServer LH 3 and LH 3r are shown in Figure 1-1.
LH 3r (Rack-Optimized)LH 3 (Pedestal)
Figure 1-1. Versions of the NetServer LH 3
Chapter 1 Introduction
2
WARNING To prevent the rack from tipping over and causing equipment
damage or bodily injury, be sure that the stabilizing, anti-tip
feature is installed on this rack enclosure (see Figure 1-2).
WARNING To prevent the rack from tipping over and causing equipment
damage or bodily injury, do not extend more than one piece
of equipment at a time out of the front of the rack enclosure.
Be sure that the stabilizing, anti-tip feature is installed on the rack enclosure in
which you are installing the HP NetServer LH 3r. This option consists of two
"feet" at the front of the base of the enclosure and, if you are installing this
NetServer in a single rack enclosure, two "feet" each on the left and right sides of
the enclosure (see Figure 1-2).
Chapter 1 Introduction
3
Figure 1-2. Single Rack Enclosure With the Anti-Tip Stabilizing
Feature Installed
Chapter 1 Introduction
4
HP NetServer LH 3r – Compaq Rack Precautions
CAUTION If this NetServer is not installed according to these
instructions, damage to the NetServer or accessories may
result. Damage due to improper installation is not covered by
the HP Warranty. Observe the precautions listed in this
section to maintain the NetServer’s reliability.
When the HP NetServer LH 3r is installed in a Compaq rack enclosure, certain
requirements must be addressed to assure that the needs of the NetServer are met.
This NetServer will meet the requirements designed for the NetServer if:
•The NetServer is installed in a Compaq model 4000- or 7000-series rack
enclosure. This NetServer is not supported in any other non-HP rack
enclosure.
•If you choose to use a door on this enclosure, only a Compaq model 4000-
or 7000-series door may be used. No other door may be used. The
enclosure may be used with the door open, closed, or removed.
•Mass storage devices listed in the Tested Products List (located on the
HP NetServer Navigator CD-ROM) are used exclusively in the NetServer.
•Use HP rack accessories. (Note that HP rack accessories are not optimized
for Compaq rack enclosures.)
Compaq rack accessories have not been tested with HP NetServer
products, but components such as monitors, keyboards, switchboxes, and
PDUs often work.
•Use APC®uninterruptible power supplies (UPS) with HP NetServers.
APC offers mounting kits for Compaq rack enclosures.
This NetServer is not supported in a rack enclosure under circumstances other
than those listed above.
See the "Warranty and Support" section of this document for additional support
considerations.
5
2Overview
The steps required to install the NetServer in the rack are summarized below:
NOTE This is only a summary; detailed instructions are provided on the
following pages.
•Measure and mark the appropriate holes on all four rack columns
•Install one bar nut on each of the four rack columns
•Insert two rack nuts on each of the two front columns only
•Attach the slides to the columns
•Extend the slides
•Remove power supply modules and hot-swap drives from theNetServer
•Lift the NetServer onto the slides
•Secure the NetServer to the slides
•Remove the lifting handles from the NetServer
•Install the power supply modules and hot-swap drives in the NetServer
•Push the NetServer back into the chassis
•Install the recessed mounting brackets on the two front columns only
Chapter 2 Overview
6
Terms used in this document are defined in the table below.
Term Definition
Bar nut Short, threaded bar used behind slide mounting flanges.
Used in place of individual nuts to mate with slide
mounting screws.
Rack nut Single nut designed to clip behind the rack column and
accept a screw through the hole in the column.
Slide Extendible side bracket which is attached to the rack
chassis columns on which the NetServer is mounted.
Consists of stationary component, and an extendible
member (see Figure 3-3). Allows access to the NetServer
after it is installed in the rack chassis.
Slide mounting flange Mounting flange located at either end of the slide (see
Figure 3-3).
Rack (rack chassis,
rack enclosure) The equipment enclosure in which the NetServer will be
installed.
Recessed mounting
brackets Two brackets (one tall, one short) that attach to the front of
the NetServer and the front rack columns to hold the
NetServer in the closed position.
EIA unit Industry standard measurement (1.75 inches / 44.45 mm),
consisting of four vertical mounting holes in a rack
column.
Otros manuales para NetServer LH 3r
2
Este manual sirve para los siguientes modelos
5
Tabla de contenidos
Otros manuales de Servidor de HP
HP
HP Integrity BL870c Manual de usuario
HP
HP Tc4100 - Server - 256 MB RAM Manual técnico
HP
HP D5970A - NetServer - LCII Manual de usuario
HP
HP ProLiant ML370 G5 Instrucciones de uso
HP
HP ProLiant ML350p Gen8 Manual de usuario
HP
HP ProLiant ML350 Generation 4p Manual de usuario
HP
HP ProLiant DL180 Gen9 Manual de usuario
HP
HP ProLiant SL165z - G6 Server Manual
HP
HP 3000 - 37XE System Manual de servicio
HP
HP ProLiant BL20p Instrucciones de uso
HP
HP ProLiant SL2500 Gen8 Manual de usuario
HP
HP ProLiant DL370 Manual de referencia
HP
HP Integrity rx1600 Manual de usuario
HP
HP D7171A - NetServer - LPr Manual de usuario
HP
HP 124708-001 - ProLiant Cluster - 1850 Manual de usuario
HP
HP Integrity BL890c - i2 Server Guía de inicio rápido
HP
HP ProLiant XL730f Gen9 Server Instrucciones de uso
HP
HP AB464-9003F Manual de usuario
HP
HP Integrity BL860c i4 Manual de usuario
HP
HP ML150 - ProLiant - G6 Instrucciones de uso
