HP 9000 EPS20 Manual de usuario

Installation Guide

K Class

HP 9000 Enterprise Servers

Part No. A2375-90006

Edition 7

June 1998

E0698

Legal Notices

The information contained in this document is subject to change without notice.

Hewlett-Packard makes no warranty of any kind with regard to this material, including, but not limited

to, the implied warranties of merchantability and fitness for a particular purpose. Hewlett-Packard shall

not be liable for errors contained herein or direct, indirect, special, incidental or consequential damages

in connection with the furnishing, performance, or use of this material.

Restricted Rights Legend. Use, duplication or disclosure by the U.S. Government is subject to

restrictions as set forth in subparagraph (c) (1) (ii) of the Rights in Technical Data and Computer

Software clause at DFARS 252.227-7013 for DOD agencies, and subparagraphs (c) (1) and (c) (2) of the

Commercial Computer Software Restricted Rights clause at FAR 52.227-19 for other agencies.

HEWLETT-PACKARD COMPANY 3000 Hanover Street Palo Alto, California 94304 U.S.A.

Reproduction, adaptation, or translation of this document without prior written permission is prohibited,

except as allowed under the copyright laws.

Trademark Notices. UNIX is a registered trademark in the United States and other countries, licensed

exclusively through X/Open Company Limited.

iii

Printing History

New editions of this manual incorporate all material updated since the previous edition. The manual

printing date and part number indicate its current edition. The printing date changes when a new edition

is printed. (Minor corrections and updates which are incorporated at reprint do not cause the date to

change.) The manual part number changes when extensive technical changes are incorporated.

February 1995..................................................................................................................... Edition 1

September 1995.................................................................................................................. Edition 2

January 1996 ....................................................................................................................... Edition 3

June 1996 ............................................................................................................................ Edition 4

July 1997 ............................................................................................................................ Edition 5

January 1998 ....................................................................................................................... Edition 6

June 1998 ............................................................................................................................ Edition 7

Change Narrative

• Edition 7 technical changes include:

a. The addition of HP9000/K360 information throughout the manual

b. Minor changes and updates as required.

• Edition 6 technical changes include:

a. The addition of HP9000/K380/K580 information throughout the manual.

b. Minor changes and updates throughout the manual.

NOTE Reader Comments. We welcome your comments about our documentation. If you have

editorial suggestions or recommend improvements for this document, please write to us.

You can reach us through e-mail at: hardwa[email protected]p.com or by sending your letter

to: Documentation Manager, M/S 5657, Hewlett-Packard Company, 8000 Foothills Blvd.,

Roseville, CA 95747-5657 USA. Please include the following information in your

message:

• Title of the manual you are referencing.

• Manual part number (from the title page).

• Edition number or publication date (from the title page).

• Your name.

• Your company’s name.

SERIOUS ERRORS, such as technical inaccuracies that may render a program or a

hardware device inoperative, should be reported to your HP Response Center or directly

to a Support Engineer.

Preface

This edition of the HP 9000/Kxx0 Installation Guide contains technical information about HP 9000

Computers. The HP 9000/Kxxo family of computers includes the following models:

HP9000/Kxx0

Servers HP9000 Workstations

K100 HP VISUALIZE K260-EG

K200

K210 HP VISUALIZE K460-XP

K220

K250

K260

K270

K360

K370

K380

K400

K410

K450

K460

K470

K570

K580

Introduction

This Installation Guide illustrates the procedures for installing the HP 9000 K Class computers. The

contents of this guide include:

1. Overview of System Installation - a brief description of the installation procedure.

2. Overview of System Power/Data Cabling - A reference figure showing the basic power and data

connections for the core system (Computer and Console).

3. Installation Steps - A series of figures showing each step in the installation process. Brief

explanations below each figure provide additional information.

Introduction

Overview of System Installation

1. Standard Console, Keyboard, and Optional Uninterruptible Power System (UPS):

a. Connect the console data cable to the "Console" port on the core I/O card of the computer.

b. Plug the standard console power cable into a UPS power receptacle.

c. Connect the keyboard cable to the keyboard connector on the console.

d. Connect the UPS data cable between the "UPS" connector on the core I/O and the appropriate

data connector on the UPS.

2. Local Area Network (LAN), Fast/Wide Differential SCSI, and Parallel Device Cabling:

a. Connect the LAN to either the "10BASE-T" or "AUI" connector on the core I/O card.

b. Connect a Fast/Wide Differential SCSI cable or terminator to the "F/W DIFF. SCSI" connector on

the core I/O card.

c. Connect a Fast/Wide Differential SCSI cable or terminator to the "F/W DIFF. SCSI" connector on

the core I/O card.

d. Connect an optional parallel device (such as a printer) to the connector labeled "PARALLEL" on

the core I/O card.

3. Internal or External Modem, and MDP:

a. Connect a line access module (LAM) to the "INTERNAL MODEM" connector on the core I/O

card. If using the internal modem, do not connect an external modem. Skip to Step C below.

b. If not using the internal modem, connect the external modem to the "EXTERNAL MODEM"

connector on the core I/O card.

c. Connect the Modem Distribution Panel (MDP) to the "MDP" connector on the core I/O card.

4. Power Connections:

a. If you are using an Uninterruptible Power System (UPS), plug the computer power cable into the

receptacle at the upper-left corner of the UPS, then plug the UPS power cable into wall power.

b. If not using the UPS, connect the computer power cable directly to wall power.

5. Stabilizer Block (Chock Block):

a. Roll the computer cabinet onto the stabilizer block in the desired location to prevent the cabinet

from being inadvertently moved around.

6. Power On:

a. Turn on the UPS

b. Turn on all peripherals

c. Turn on the computer by setting the key switch to the "ON" position.

d. Refer to the Owner’s Guide that came with your computer for operator information.

Introduction

Overview of System Installation

Optional Graphics Console

If desired, a graphics console and mouse can be connected to the SPU instead of the standard console.

To install the graphics console, substitute the following Step 1 for the standard Step 1 in the installation

procedure listed above:

Optional Graphics Console: A4032A/A4033A/A4331A Graphics Display with Keyboard and

Mouse:

1. Connect the graphics console data cable to the "OPTIONAL I/O" port on the system core I/O card.

2. Plug the graphics console power cable into a UPS power receptacle.

3. Plug the graphics console power cable into a UPS power receptacle.

4. Connect the keyboard cable to the keyboard connector on the core I/O card.

5. Connect the mouse cable to the connector labeled "MOUSE" on the system core I/O card.

6. Connect the UPS data cable between the "UPS" connector on the system and the appropriate data

connector on the UPS.

Overview of System Power/Data Cabling

CAUTION UPS Requirements

The 1.8kVA (A2997A), 3kVA (A2998A), and 5.5kVA (A3589A) Power Trust UPSs

are the only UPSs supported on PA8000-based systems: HP9000

K250/K260/K370/K380 and HP9000 K450/K460/K570/K580. The 1.3kVA and

1.6kVA Power Trust UPSs do not have a 20amp receptacle and cannot provide

sufficient current.

Rackmount Requirements

Ensure that the PDU (cabinet power strip) has a 20 amp receptacle. Upgrade kits for the

PDU strip are available if required.

Introduction

Overview of System Installation

The figure below shows an overview of the power and data cabling for the system, console, and the

optional UPS, and is intended for reference only. Cable part numbers may not be the same for all

systems.

To proceed with actual installation of the system, start at the page titled "Standard Console, Keyboard,

and Optional UPS".

Introduction

Standard Console, Keyboard, and Optional UPS

(K100/K200/K210/K220/K400/K410/K420)

1. Connect the standard console data cable to the "Console" port on the core I/O board of the system.

2. Plug the standard console power cable into a UPS power receptacle.

3. Connect the keyboard cable to the keyboard connector on the console.

4. Connect the UPS data cable between the "UPS" connector on the system and the appropriate data

connector on the UPS.

NOTE Do not plug the UPS into a power receptacle at this time.

Introduction

Optional Graphics Console: A4032A/A4033A/A4331A Graphics Display with Keyboard and Mouse

Optional Graphics Console: A4032A/A4033A/A4331A

Graphics Display with Keyboard and Mouse

NOTE An A4032A or A4033A Graphics Console may be connected to the system instead of the

standard console.

Otros manuales para 9000 EPS20

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Servidor de HP

HP PROLIANT 580554-001 Manual de usuario

HP Rx2620-2 - Integrity - 0 MB RAM Manual de usuario

HP ProLiant DL160 Gen9 Manual

HP ProLiant DL38 Instrucciones de funcionamiento y seguridad

HP HPE ProLiant ML30 Gen9 Manual de usuario

HP Integrity rx1600 Manual de instrucciones

HP ProLiant DL580 Generation 3 Manual de usuario

HP DL590/64 Manual de usuario

HP A4500A - VMEbus Single Board Computer 744... Manual del propietario

HP 2533t - Compaq Mobile Thin Client Manual de usuario

HP BladeSystem bc2000 - Blade PC Instrucciones de funcionamiento y seguridad

HP D7171A - NetServer - LPr Manual de usuario

HP ProLiant DL320G5p/X3075 Instrucciones de instalación

HP cc2300 Manual de usuario

HP ProLiant PC2-6400 Instrucciones de uso

HP Integrity Superdome X Instrucciones de uso

HP D7171A - NetServer - LPr Manual de lista de piezas

HP t5710 - Thin Client Manual de usuario

HP Rp3440-4 - 9000 - 0 MB RAM Guía de inicio rápido

HP DesignJet T610 Manual de usuario

HP StorageWorks FC4-16 Manual de usuario

HP ProLiant DL385p Manual de usuario

HP ProLiant DL380p Manual de usuario

HP Integrity rx1620 Guía de inicio rápido

Manuales populares de Servidor de otras marcas

Dell

Dell PowerEdge R410 Manual de usuario

PowerNAS

PowerNAS CMA Manual de usuario

Supero

Supero FatTwin F617R3-FT Manual de usuario

MSI

MSI P1-109N-L70 Manual de usuario

Dell

Dell PowerEdge XE9640 Manual

Dell

Dell PS4100 Instrucciones de montaje

EtroVISION

EtroVISION EV3151 Manual de usuario

NEC

NEC Express5800/T110j Manual de usuario

Compaq

Compaq ProLiant 3000 Manual

Dell

Dell PowerEdge 3YPMN Manual de usuario

iRobo

iRobo IPC2U Manual de usuario

Nortel

Nortel 1000 Con?guration guide Manual de usuario

Asus

Asus AP7500 Manual de operación y mantenimiento

Avid Technology

Avid Technology AirSpeed 5000 Manual de usuario

Milestone

Milestone Husky IVO 350T Manual de usuario

Planet

Planet NAS-7410 Manual de usuario

Lenovo

Lenovo ThinkSystem SR635 V3 Manual de usuario

Dell

Dell PowerEdge HS5610 Manual