HP ProCurve 1600M Manual de usuario

1

HP ProCurve 8-Port Power Supply Clip

Installation and Removal

HP ProCurve 8-Port Power Supply Clip (5184-5887) is supported for use on the following switches:

■HP ProCurve 2615-8-PoE Switch (J9565A)

■HP ProCurve 2915-8G-PoE Switch (J9562A)

Note Prior to installing or removing the Power Supply clip assembly, be sure the power adapter and all cables

have been disconnected and removed.

Installation

1.Align the clip with the switch

in the orientation shown.

A

B

C

2.First, insert two alignment

pins on one side of the clip into

the appropriate holes on the

switch (A).

3. Then, align the two

thumbscrews on the other side

of the clip (B), and secure the

clip onto the switch (C).

CAUTION:

Use caution when tightening the thumbscrews to the switch. Using excessive force may damage the thumbscrew

or hole threads.

4. Slide the power adapter into the

retention clip from the side as illustrated.

CAUTION:

Do not install or remove the adapter

by lifting the clip and forcing the

adapter directly into, or out of, the

housing area.

© Copyright 2010 Hewlett-Packard Development Company, L.P.

The information contained herein is subject to change without notice.

The only warranties for HP products and services are set forth in the express

warranty statements accompanying such products and services. Nothing

herein should be construed as constituting an additional warranty. HP will

not be liable for technical or editorial errors or omissions contained herein.

Printed in China

March 2010

Manual Part Number: 5998-0408

*5998-0408*

5998-0408 PS Clip QSG-Mar10.fm Page 1 Tuesday, February 23, 2010 1:44 PM

2

Removal

Note Before removing the power supply clip assembly from the switch:

1. First, unfasten the two

thumbscrews that attach the clip

assembly to the switch (A).

Carefully slide this side off first.

A

B

2. Then disengage the alignment

pins on the other side of the clip

assembly (B), and slide the entire

assembly away from the switch.

• Disconnect and remove the power adapter and cables.

• If a cable tie is used to secure the adapter power cord, it must be removed.

• Be sure to remove the power adapter by sliding it out from the side of the clip assembly.

5998-0408 PS Clip QSG-Mar10.fm Page 2 Tuesday, February 23, 2010 1:44 PM

Otros manuales para ProCurve 1600M

25

Tabla de contenidos

Otros manuales de Fuente de alimentación de HP

Manuales populares de Fuente de alimentación de otras marcas

Monacor

Monacor PS-12CCD Manual de usuario

VOLTIMA

VOLTIMA MagicBox 15 Manual de usuario

Agilent Technologies

Agilent Technologies 6032A Manual de usuario

Miller

Miller Auto Deltaweld 452 Manual de usuario

BCP

BCP PUOUBK Hoja de instrucciones

HC

HC 2210 Manual de usuario

Puls

Puls CT5.241 Manual de usuario

OCZ

OCZ ZX1250W Manual de usuario

iseg

iseg ECH 238 Manual de usuario

Power

Power XXL A Series Manual de usuario

Agilent Technologies

Agilent Technologies 6631B Manual de usuario

Renogy

Renogy PHOENIX 300 Manual de usuario

Epson

Epson Stylus Scan 2500 Manual de funcionamiento

Pulsar

Pulsar GREEN POWER CCTV PoE POE044816 Manual de usuario

Puls

Puls MiniLine ML50.100 Manual de usuario

Puls

Puls AS-Interface SLA4.100 Manual de usuario

Kenwood

Kenwood PS-60 Manual de usuario

Elmdene

Elmdene G1380xN-y-s Series Manual de usuario