HP D7171A - NetServer - LPr Manual de instalación y operación

HP NetServer

LH 3000/3000r and

LH 6000/6000r

Power Supply Upgrade Guide

HP Part Number 5969-2160

Printed in November 1999

Notice

The information contained in this document is subject to change without notice.

Hewlett-Packard makes no warranty of any kind with regard to this material,

including, but not limited to, the implied warranties of merchantability and fitness

for a particular purpose. Hewlett-Packard shall not be liable for errors contained

herein or for incidental or consequential damages in connection with the

furnishing, performance, or use of this material. Hewlett-Packard assumes no

responsibility for the use or reliability of its software on equipment that is not

furnished by Hewlett-Packard.

This document contains proprietary information that is protected by copyright. All

rights are reserved. No part of this document may be photocopied, reproduced, or

translated to another language without the prior written consent of

Hewlett-Packard Company.

3M®is a registered trademark of Minnesota Mining and Manufacturing Company.

Hewlett-Packard Company

Network Server Division

Technical Communications / MS 45SLE

10955 Tantau Avenue

Cupertino, CA 95104 USA

Audience Assumptions

This guide is intended for the person who installs, administers, and troubleshoots

network servers. Hewlett-Packard Company assumes you are qualified in the

servicing of computer equipment and trained in recognizing hazards in products

with hazardous energy levels.

iii

Contents

1 Introduction ................................................................................................. 1

Accessory Kit Contents.................................................................................. 1

Tools and Related Documentation................................................................. 2

Contents of This Guide.................................................................................. 2

Precautions................................................................................................... 2

2 HP NetServer LH 3000: Installing a Power Supply and Fan....................... 5

Remove NetServer Covers........................................................................ 5

Install Power Supply Fan Module............................................................... 6

Install Power Supply.................................................................................. 8

Finishing the Installation.......................................................................... 10

3 HP NetServer LH 6000: Installing a Power Supply and Fan..................... 11

Remove NetServer Covers...................................................................... 11

Install Power Supply Fan Module............................................................. 12

Install Power Supply................................................................................ 14

Finishing the Installation.......................................................................... 16

4 Warranty and Support............................................................................... 17

HP Repair and Telephone Support .............................................................. 17

5 Regulatory Information ............................................................................. 19

Index............................................................................................................... 21

1 Introduction

This guide describes how to install a power supply upgrade kit, HP Product

Number D8551A, in an HP NetServer LH 3000/3000r or an HP NetServer

LH 6000/LH 6000r.

The power supply upgrade kit provides a redundant power supply that allows the

NetServer to keep operating should one of the original power supplies fail. The

redundant power supply fan module, also shipped with the upgrade kit, provides

additional cooling and allows the NetServer to keep operating in case the original

fan module fails.

After installing the power supply upgrade kit, you can remove and replace a failed

power supply without powering down the NetServer.

CAUTION If you remove a power supply on a hot-swap basis, you must

immediately install a replacement power supply or a power

supply filler panel to prevent overheating problems.

Removing a power supply on a hot-swap basis bypasses the

cooling air around the adjacent power supply. Leaving a

power supply bay empty for too long can cause the remaining

power supplies to overheat and may cause a system shutdown.

Accessory Kit Contents

The contents of the shipping box include:

Power supply module

Power supply fan module

Power cord for power supplies 3 and 4 (required for LH 3000/3000r only)

•HP NetServer LH 3000/3000r and LH 6000/6000r Power Supply Upgrade

Guide (this guide)

Chapter 1 Introduction

Tools and Related Documentation

To install a redundant power supply, you need an anti-static service kit

(3M8501/8502/8503 or equivalent). This kit includes a static-dissipating mat.

The following documents describe the HP NetServer LH 3000/3000r or

LH 6000/6000r:

•HP NetServer Installation Guide

•HP NetServer Online Documentation CD-ROM

Contents of This Guide

This guide includes the following chapters:

•Installing a power supply and fan in an HP NetServer LH 3000/3000r

Installing a power supply and fan in an HP NetServer LH 6000/6000r

•Warranty and support information

Precautions

CAUTION Components of this accessory kit are sensitive to static

electricity and can be damaged by improper handling. Read

the following information carefully before you handle the

accessory components:

•Leave the components in the anti-static container until you

are ready to install them.

•Use an anti-static wrist strap and a grounding mat. Read

and follow the instructions included with the wrist strap

and mat.

•Before you remove a component from its anti-static

container, touch a grounded, unpainted metal surface on

the NetServer to discharge static electricity.

Chapter 1 Introduction

WARNING Before removing the cover, always disconnect the power cord

and unplug telephone cables. Disconnect the power cord to

avoid exposure to high energy levels that may cause burns

when parts are short-circuited by metal objects, such as tools

or jewelry. Disconnect telephone cables to avoid exposure to

shock hazard from telephone ringing voltages.

WARNING The power switch does not turn off the standby power.

Disconnect the power cord to turn off standby power. If the

backlight on the LCD display is still on, standby power is still

on.

2 HP NetServer LH 3000/3000r:

Installing a Power Supply and Fan

To install a redundant power supply into an HP NetServer LH 3000/3000r, you

will follow these steps:

Remove NetServer covers.

Install power supply fan module.

Install power supply.

Finish the installation.

NOTE For instructions on installing a power supply and fan into an

HP NetServer LH 6000/6000r, see Chapter 3.

Remove NetServer Covers

1. Close all applications, log off all users, and power down the NetServer.

2. Disconnect all power and telephone cords.

WARNING Before removing the cover, always disconnect the power cord

and unplug telephone cables.

3. Remove appropriate covers as follows:

a. For the pedestal version of your NetServer, remove the front bezel and

the left cover as described in the HP NetServer LH 3000/3000r

Installation Guide.

b. For the rack-mounted version of your NetServer, follow these steps.

See the HP NetServer LH 3000/3000r Installation Guide for further

details.

1. Extend the anti-tip foot.

2. Remove the front bezel.

3. Remove the screws that secure the front of the NetServer to the

rack.

Chapter 2 HP NetServer LH 3000/3000r: Installing a Power Supply and Fan

4. From the front of the NetServer, pull the NetServer forward until

you hear the locking device engage with a click.

5. Remove the top cover by loosening the thumbscrew and lifting the

cover away from the NetServer.

Install Power Supply Fan Module

The redundant power supply fan module allows the NetServer to keep operating in

case the original fan fails.

1. Locate the power supply fan module, and press down on the tab to unlock

the hinged handle. As shown in Figure 2-1, this tab locks the handle in the

closed position.

Press down on the tab

to unlock the hinged handle.

Figure 2-1. Unlock the Hinged Handle on the Power Supply Fan Module

2. Locate the panel where you will insert the redundant power supply fan

module shipped with this upgrade kit. See Figure 2-2. As you insert the fan

module, this hinged panel rotates up and out of the way.

3. With the hinged handle open, insert the power supply fan module as shown

in Figure 2-2.

Otros manuales para D7171A - NetServer - LPr

117

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Fuente de alimentación de HP

HP 6034A Manual de usuario

HP StorageWorks 1000 - Modular Smart Array Instrucciones de funcionamiento

HP 59501A Manual de usuario

HP Entry-Level Instrucciones de uso

HP 711A Manual de servicio

HP E3633A Manual de usuario

HP 66312A Instrucciones de funcionamiento

HP 6259B Manual de servicio

HP xw8600 - Workstation Instrucciones de funcionamiento

HP HVB Series Manual de usuario

HP procurve switch zl Manual de usuario

HP SCR-1P Series Manual de servicio

HP 6200B Manual de servicio

HP D7171A - NetServer - LPr Manual de usuario

HP SCR-1P Series Manual de servicio

HP E3610A Manual de servicio

HP 11900 Manual de usuario

HP E3631A Guía

HP FlexFabric 11900 2500W AC Manual de usuario

HP BENCH Series Manual de servicio

HP 654A Manual de usuario

HP 640 RPS/EPS Manual de usuario

HP PSR750-A Manual de usuario

HP HPE Synergy 12000 Frame Manual de usuario

Manuales populares de Fuente de alimentación de otras marcas

Monacor

Monacor PS-12CCD Manual de usuario

VOLTIMA

VOLTIMA MagicBox 15 Manual de usuario

Agilent Technologies

Agilent Technologies 6032A Manual de usuario

Miller

Miller Auto Deltaweld 452 Manual de usuario

BCP

BCP PUOUBK Hoja de instrucciones

HC 2210 Manual de usuario

Puls

Puls CT5.241 Manual de usuario

OCZ

OCZ ZX1250W Manual de usuario

iseg

iseg ECH 238 Manual de usuario

Power

Power XXL A Series Manual de usuario

Agilent Technologies

Agilent Technologies 6631B Manual de usuario

Renogy

Renogy PHOENIX 300 Manual de usuario

Epson

Epson Stylus Scan 2500 Manual de funcionamiento

Pulsar

Pulsar GREEN POWER CCTV PoE POE044816 Manual de usuario

Puls

Puls MiniLine ML50.100 Manual de usuario

Puls

Puls AS-Interface SLA4.100 Manual de usuario

Kenwood

Kenwood PS-60 Manual de usuario

Elmdene

Elmdene G1380xN-y-s Series Manual de usuario