HP 24wd Manual de usuario

HP 24wd LED Backlit Monitor

User Guide

Microsoft, Windows, and Windows Vista are either trademarks or registered trademarks of Microsoft

Corporation in the United States and/or other countries.

The only warranties for HP products and services are set forth in the express warranty statements

accompanying such products and services. Nothing herein should be construed as constituting an

additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein.

This document contains proprietary information that is protected by copyright. No part of this document

may be photocopied, reproduced, or translated to another language without the prior written consent of

Hewlett-Packard Company.

First Edition (October 2012)

Document Part Number: 715991-001

Chapter I. Introduction

1.1 Features

Multilingual OSD adjustment

Compatible with IBM VGA, extended VGA, VESAVGA, SVGA, XGA, and SXGA modes

Wide range of applicable voltages (AC 100-240V 50/60Hz ) enables direct use without any

setting.

Plug-and-play VESA DDC1/ 2B Standard. Compatible with Windows 9x / 2000 / XP / 7 / Vista

operation systems

1.2 Check list

Please make sure the following items are included with your LCD monitor;

The monitor (and the pedestal)

Lower stand

Power cord

Adapter

VGA cable

DVI cable (Optional)

Documentation and software CD

Setup poster

Warranty certificate (Optional)

If any of these items are missing, please contact your dealer for technical support and custom

service.

Note: Be sure to save original box and all packing materials for future transport.

Chapter II. Installation

2.1 Install the pedestal

Please follow the steps illustrated below to install the pedestal.

2.2 Connect your monitor to your computer

1. Power off and unplug your computer.

2. Connect the 15-Pin ends of the signal cable to the VGA port of your monitor and the VGA OUT jack

on the back of your computer. Secure the screws on both ends of the signal cable.

3. Connect the round end of power adapter to the monitor, then connect one end of the power cords to

the power adapter and the other end to the nearest electrical outlet.

4. Power on your computer and monitor. If your monitor displays an image, the installation has been

successfully done. If the monitor does not display any image, check all the connections.

Cautions: 1. For installation, please complete signal cord connection before plugging the power cord

into the electrical outlet to avoid damaging the monitor.

2. During installation, please support the front frame with your hand at its center of gravity to

avoid dropping and damaging the monitor.

Overview of the ports of the monitor:

1. DC power supply input

2. DVI signal input

3. VGA signal input

2.3 Disconnect the pedestal for shipping

Press the clip button on the pedestal and remove the pedestal from the stand.

Chapter III.Monitor overview

Overview of front panel controls

Chapter IV. Operational Instruction

4.1Power ON/OFF Switch

Press this button to power on/off your monitor. Note: The ON/OFF switch does not disconnect your

monitor from the main voltage. To completely disconnect the main voltage, please remove the

power plug from the socket.

4.2 Power indicator

The power LED is blue when the monitor operates normally. If the monitor runs in power-saving

mode, this indicator changes to amber. When the monitor is turned off, this indicator is unlit.

4.3 Menu features

All the following features of your monitor can be accessed and adjusted by using the on screen

display (menu) system.

1. If your monitor is not powered on, press the "Power” button to turn it on.

2. Press the "Menu” button to activate the OSD menu. The OSD main menu will be displayed.

3. To view the main menu or submenu, press the “+” on the front panel of your monitor to scroll up

or the “-” to scroll down. Then press the "OK” button to select a highlighted function.

When the highlight scrolls down to the bottom of the menu, it returns to top of the menu. When the

highlight scrolls up to the top of the menu, it returns to bottom of the menu."

4. To adjust the selected option, press the “+” or “-” button.

5. Select “Save” and return. If you do not want to save the setting, select “Cancel” from the

submenu or “Exit” from the main menu.

6. Press the “Menu” button to exit from the OSD menu.

4.4 OSD operational instructions

Icon Main menu

option

Submenu option Note

Brightness To adjust the brightness level of the

screen. The factory default range is

90.

Contrast To adjust the contrast level of the

screen.The factory default range is

80.

Color Selects the screen color.The

factory is 6500K or Custom

color,depending on the mode.

Warm- 5000K Changes color to slightly reddish

white.

Standard- 6500K Uses standard colors (default).

Cool- 9300K Change color to slightly blueish

white.

Custom (RGB)

Selects and adjusts your own color

scales:

Red Color – sets your own red color

levels.

Green Color – sets your own green

color levels.

Blue Color – sets your own blue

color levels.

Image control

To adjust the image on the screen.

The ambient brightness sensor can

also be enabled or disabled (only

applicable to some models)

Auto-adjustment To automatically adjust the image

on the screen (only applicable to

VGA input).

Clock and Phase

To adjust the clock phase of the

screen.

This adjustment eliminates all

horizontal noises to enable clearer

and more lifelike images and

characters (only applicable to VGA

input)

Horizontal position To adjust the horizontal position of

an image (only applicable to VGA

input).

Vertical position To adjust the vertical position of an

image (only applicable to VGA

input).

Custom Scaling

Selects the method on how

displayed information on the

monitor will be formatted.Select

Fill to Screen – image fills the entire

screen and may look distorted or

elongated because of

non-proportional scaling of height

and width.

Fill to Aspect Ration – image is

sized to fit the screen and maintains

proportional image.

Sharppness Adjusts the screen imageto look

sharper or soft.

Dynamic Contrast Turns Dynamic Contrast Ratio On

or Off.The factory default is Off.

OSD Control Provides a menu for adjusting the

on-screen display(OSD)control.

OSD position To adjust OSD position for your

monitor.

Horizontal OSD

Position

To adjust the visual position of the

OSD menu to the right or left of the

screen. The factory default

horizontal position value is 97.

Vertical OSD

Position

To adjust the visual position of the

OSD menu up or down the screen.

The factory default vertical position

value is 13.

OSD Transparency To adjust the transparency to

enable transparent background

information under the OSD.

OSD Timeout To set the OSD display time (in

seconds) after the last pressing the

button. The factory default setting is

Tabla de contenidos

Manuales populares de Monitor de otras marcas

Linear Acoustic

Linear Acoustic LQ-1000 Manual de usuario

AOC

AOC I2579V Manual de usuario

Gateway

Gateway FPD1520 Manual de usuario

Furuno

Furuno Mu 120c Manual de usuario

Asus

Asus VB171D - 17" LCD Monitor Manual de usuario

Dell

Dell S2230MX Instrucciones de uso

Philips

Philips 107C64 Manual de usuario

Dell

Dell S2409WFP Manual de usuario

EverFocus

EverFocus EN-7517E Manual de usuario

Panasonic

Panasonic TH152UX1 - 152" PLASMA TV Manual de usuario

Dell

Dell Precision 7680 Manual de instrucciones

LG 50PM1M - - 50" Plasma Panel Manual de usuario

Bosch

Bosch DDU 9 Manual de usuario

Acer

Acer A231HL Manual de usuario

Philips

Philips 86BDL4152T Manual de usuario

NEC

NEC AccuSync LCD5V Manual de usuario

Emay

Emay SleepO2 Manual de usuario

IBM

IBM 6360 Instrucciones de instalación