HP StorageWorks MSA2000 3.5 Manual de usuario

Otros manuales de Recinto de HP

HP

HP STORAGEWORKS ALL-IN-ONE STORAGE SYSTEM Manual de usuario

HP

HP BladeSystem c3000 Manual de usuario

HP

HP StorageWorks 2000fc - G2 Modular Smart Array Manual de usuario

HP

HP TeemTalk Terminal Emulator 7.0 Guía

HP

HP V-class Series Instrucciones de montaje

HP

HP 418800-B21 - StorageWorks Modular Smart Array 70 Storage... Manual de usuario

HP

HP D3600 Manual

HP

HP StorageWorks 50 Instrucciones de uso

HP

HP HPE D6020 Manual de usuario

HP

HP D6000 Disk Enclosure Manual de usuario

HP

HP BladeSystem c7000 Instrucciones de funcionamiento y seguridad

HP

HP P9K37A Manual de usuario

HP

HP A1896A Manual de usuario

HP

HP StorageWorks 50 Manual de usuario

HP

HP MSA 1050 Manual de usuario

HP

HP A3765A Manual de usuario

HP

HP BladeSystem c3000 Manual de usuario

HP

HP Clemco 60 Guía

HP

HP d3000 Instrucciones de montaje

HP

HP BladeSystem c-Class Infrastructure Instrucciones de uso

HP

HP HPE D6020 Manual

HP

HP BladeSystem c3000 Manual de usuario

HP

HP NonStop G16SE Manual de usuario

HP

HP StorageWorks MSA50 Instrucciones de uso

Manuales populares de Recinto de otras marcas

SilentiumPC

SilentiumPC Armis AR5 Manual

Pulsar

Pulsar 17/TRP80/DSPR Manual de usuario

Thermaltake

Thermaltake V150 TG Manual de usuario

MSI

MSI MPG SEKIRA 500X Manual de usuario

Antec

Antec Dark fleet DF-10 Manual de usuario

Nexans

Nexans WTC05 Manual de usuario

Peavey

Peavey DS 1502 Manual de usuario

D-Link

D-Link ShareCenter Pro DNS-1550-04 Manual de usuario

Rosewill

Rosewill RX82-U(JBOD) Manual de usuario

QNAP

QNAP SAS JBOD CLI 1.0 Manual de usuario

GAMDIAS

GAMDIAS Talos P1 Manual de usuario

Auvs

Auvs KR615 Manual de usuario

Digitus

Digitus DA-71114 Manual de usuario

CommScope

CommScope FDH 3000 Manual de usuario

FS

FS FHD-FWME4 Manual de usuario

JBL

JBL CS1215T Manual de usuario

Pulsar

Pulsar ARAD-S4 Manual de usuario

Pulsar

Pulsar AWO454 Manual de usuario

Page 1

481603-002

About this document

This document describes the procedure for installing an I/O module

into an HP StorageWorks MSA2000 3.5 12-drive enclosure.

IMPORTANT: Install this module only into an MSA2000 3.5

12- d r iv e e n c l o s u r e .

CAUTION: Parts can be damaged by electrostatic discharge.

Use proper anti-static protection.

•Keep the replacement component in the ESD bag until needed.

•Wear an ESD wrist strap grounded to an unpainted surface of

the chassis.

•If an ESD wrist strap is unavailable, touch an unpainted surface

of the chassis before handling the component.

•Never touch connector pins.

Removing the air management blank

CAUTION: When upgrading an existing operational system

with an I/O module, removing the blank impacts the airflow and

cooling ability of the device. To avoid possible overheating, insert

the I/O module as quickly as possible. If the internal temperature

exceeds acceptable limits, the enclosure may overheat and

automatically shut down or restart.

NOTE: For clarity, only relevant details are shown in these

illustrations.

1. Turn the thumbscrews until the screws disengage from the blank.

2. Press both latches downward.

3. Pull the blank straight out of the enclosure.

1Latch 2Thumbscrew

12 12

Printed on at least 50% total recycled fiber with at least 10%

post-consumer paper

© Copyright 2008 Hewlett-Packard Development Company, L.P.

Second edition: November, 2008

Product names mentioned herein may be trademarks of their

respective companies as reflected by an associated footnote. The

information in this document is subject to change without notice.

Printed in China.

www.hp.com

HP StorageWorks

MSA2000 3.5 12-Drive

Enclosure

I/O module installation

instructions

Page 2

Installing the I/O module

1. Loosen the thumbscrews; press the latches downward.

2. Slide the I/O module into the enclosure as far as it will go (1).

3. Press the latches upward to engage the I/O module (2); turn the

thumbscrews finger-tight.

4. Connect cables according to a supported configuration. See the

user guide.

Verifying I/O module status

In an operational system, once the I/O module is installed and

cabled:

•Verify that the heartbeat LED on the front of the enclosure is

green.

•Verify that the OK LED on the back of the new I/O module is

green.

Additional information

See the MSA web site: http://www.hp.com/go/msa.

2

1

2