HP Vectra XU 5/XX Manual de referencia

HP Vectra XU PC – Setting Up In This Manual •• 1

Setting Up Your HP Vulcan XU PC

Introduction

HP Vectra XU PC – Setting Up In This Manual •• 2

In This Manual

Installing Accessories

Overview

Removing the Cover

Converting from a Desktop to a Deskside Unit

Where to Install the Accessories

Installing Mass Storage Devices

Installing IDE Devices

Installing SCSI Devices

Software Installation

Installing a Front-Access Device in the Middle or Bottom shelf

Installing a Hard Disk Drive in the Rear Shelf

Installing a Hard Disk Drive in the Bottom Shelf

Remove the Power Supply

Installing Main Memory Modules

Installing an Upgrade Processor

Setting the System Board Switches

Replacing the Power Supply

Installing Accessory Boards

Video Adapter

Upgrading the Matrox Video Adapter Board Memory

VESA Pass-through Connector

Replacing the Cover

Completing the Installation Procedure

Configuring Your PC

Overview

Starting SETUP

Using SETUP to Configure the PC

Setting the Date and Time, and User Preferences

Viewing Processor and Main Memory Information

Configuring the Disk Drives

Configuring the Security Features

Configuring the Ports

Configuring the Network Interface

Configuring Accessory Boards

Configuring the Integrated Video Refresh Rates

Displaying the BIOS Version and PC Serial Number

What to do Next

Video Configuration

Configuring the Integrated Ultra VGA PCI Video Controller

Configuring the Matrox Video Adapter Board

HP Vectra XU PC – Setting Up In This Manual •• 3

Using the Matrox Video Software Tools

Using HP Utilities and HP User Tools

Using HP User Tools

Typical Icons You May Need to Use

HP Utilities (HPUtils)

The Master Diskette Creation Utility

The ShowSCSI Utility

Troubleshooting and Error Messages

Overview

If the Display Does Not Work

If the PC Does Not Work: No Error Messages

If the PC Does Not Work: Error Messages

If a POST Error Message Appears

BIOS and Operating System Error Messages

Hardware Problems

If You Lose the Key

If a Flexible Disk Drive Does Not Work

If a Hard Disk Does Not Work

If an IDE Hard Disk Does Not Work

If a SCSI Device Does Not Work

If all SCSI Devices Stop Working

If the Hard Disk Activity Light Does Not Work

If the Keyboard or Mouse Does Not Work

If the Printer Does Not Work

If an Accessory Board Does Not Work

Other Problems

If Your Application Software Does Not Work

If You Forget the Passwords

If You Can't Start SETUP

If You Can't Change the PC's Configuration in SETUP

If the Date and Time are Incorrect

If You Have Problems Running Your Backup Programs

Getting Support

Hewlett Packard Information Services

Getting Support from Hewlett-Packard

If You Need to Contact Hewlett-Packard

Recycling Your PC

Technical Information

Specifications

The PC's Memory Map

The PC's System Board Switches and Internal Connectors

Using Your PC's System Board Switches

The PC's Rear Connectors

HP Vectra XU PC – Setting Up Introduction •• 4

Introduction

In This Manual

Congratulations on the purchase of your new Hewlett-Packard Personal Computer with a

main processor and provision for an optional Dual Companion Processor.

This manual is intended for the person responsible for setting up this PC and installing

accessories in it.

This manual contains the following information:

Installing

Accessories explains how to install any hardware accessories you purchased.

Configuring Your PC explains how to configure the PC for the hardware accessories

you installed.

Using HP Utilities and

HP User Tools explains how to use HP Utilities and HP User Tools.

Troubleshooting and

Error Messages explains how to correct any problems with the PC.

Technical Information provides technical information.

Index gives an alphabetical list of the information in this manual.

NOTE If you need more information on:

•connecting the keyboard, mouse, display, and power cords, refer to the Getting

Started manual supplied with the PC

•using the PC, refer to the Getting Started manual supplied with the PC

•installing new software, refer to the application manuals

setting up a network, refer to the network manuals.

HP Vectra XU PC – Setting Up Installing Accessories •• 5

Installing Accessories

Overview

This chapter describes how to install the following accessories in the PC:

•mass storage devices — check with your dealer for supported devices:

◊◊ drives with front access, such as:

∗3.5-inch flexible disk drive

∗5.25-inch flexible disk drive

∗SCSI-2 CD-ROM

◊◊ hard disk drives

∗SCSI-2 hard disk drives

∗IDE hard disk drives

•main memory modules (installed in identical pairs):

◊◊ 4 MB memory module

◊◊ 8 MB memory module

◊◊ 16 MB memory module

◊◊ 32 MB memory module

•Dual Companion Processor

•accessory boards, such as the Matrox Video Adapter board

•2 MB Video memory upgrade for Matrox Video Adapter board (Only for models that are

supplied with a Matrox Video Adapter).

For information on product numbers and other supported accessories, refer to the product

datasheet.

When installing accessories:

•You will need a "medium" tip flat-blade screwdriver. The tip should be 6 mm wide.

•Keep any parts you remove from the PC in a safe place, in case you need to install

them again later.

•If you have a PC with a SCSI hard disk drive and you wish to install an IDE hard disk

drive, refer to the section Installing IDE Devices in this chapter before installing the

drive.

•If you install non-supported disk drives, or you have two hard disk drives fitted, you may

have to set jumpers or switches on the drives, or change the drive data cable. (Refer to

the manual supplied with the accessory disk drive for more information.)

HP Vectra XU PC – Setting Up Installing Accessories •• 6

•Before installing accessory boards, check available system resources and change the

board's switch settings if necessary. (Refer to Installing Accessory Boards.)

•After installing accessories, check the PC's configuration by running SETUP. (Refer to

“Configuring Your PC”.) If you installed ISA accessory boards, run the ISA

Configuration Utility in the Plug and Play group, in Windows. (Refer to Installing

Accessory Boards, later in this chapter.)

WARNING For your safety, never remove the PC's cover without first removing the power

cord, and any connection to a telecommunications network.

Some large displays are heavier than one person can lift safely. Refer to the

display's documentation. If in doubt, never lift a large display without help.

Removing the Cover

1. Switch the PC and display OFF.

2. Disconnect the power cords from the power outlets. Disconnect the power cords from

the PC and display, then remove the display.

HP Vectra XU PC – Setting Up Installing Accessories •• 7

3. Unlock the cover using the key provided with the PC.

4. Unclip the tabs on each side of the cover, at the back of the PC.

5. Slide the cover forward 5 cm (2 inches), and lift it up and off the PC.

Converting from a Desktop to a Deskside Unit

Your PC can be used in either a desktop or a deskside position.

1. Remove the PC's cover as described earlier in this chapter.

2. Change the nameplate as follows:

a. From behind the front panel, push the nameplate's stem to release the locking tabs

from the cover.

b. Turn the nameplate into its deskside position. Align the key on the nameplate with

the hole in the cover. Then push the nameplate back into the cover.

HP Vectra XU PC – Setting Up Installing Accessories •• 8

3. Change the control panel as follows:

a. Ease the top of the control panel forward. Remove it from the PC, leaving its cable

attached.

b. Turn the control panel into its deskside position. Insert the plastic tabs into the frame.

Ensure the metal case around the panel is inside the frame. Gently push the control

panel back into place.

4. Install any other accessories before replacing the cover.

Where to Install the Accessories

Disk drives and accessory boards can be installed without moving the power supply. You will

need to move the power supply to install main memory or add an upgrade processor.

HP Vectra XU PC – Setting Up Installing Accessories •• 9

Accessory Boards Upgrade Processor

Memory Modules

Installing Mass Storage Devices

The PC uses flexible disk drives, IDE hard disk drives, and SCSI-2 drives. For other devices,

you may need to install a controller board or remove terminating resistors.

The PC is supplied with a 3.5-inch 1.44 MB flexible disk drive installed in the top shelf. Some

models have a hard disk drive already installed. The PC has four shelves for mass storage

devices — check with your dealer for supported devices:

•the top shelf has a 3.5-inch "slim" (1-inch high) 1.44 MB flexible disk drive.

•the middle shelf can be used for any 5.25-inch half-height front-access device, such as

a flexible disk drive or CD-ROM drive.

•the bottom shelf can be used for a secondary 3.5-inch or 5.25-inch hard disk drive, or

for any 5.25-inch half-height front-access device.

•the rear shelf is used for a primary 3.5-inch or 5.25-inch hard disk drive.

HP Vectra XU PC – Setting Up Installing Accessories •• 10

Hard

Disk Flexible

Disk

Drive

CD-

ROM

Drive

Hard Disk

Installing IDE Devices

If you have a PC with a SCSI hard disk drive and you install an unformatted IDE hard disk

drive with no operating system on it, the PC will not boot. This is because after installing an

IDE hard disk drive it will always be the bootable drive.

NOTE In this case, before installing an IDE hard disk drive, make bootable copies of the

operating system.

•For PCs with the DOS/Windows operating system, use the Master Diskette Creation

Utility, located in the HP Utils Group in Windows. Refer to the operating system

documentation for information on formatting a drive and installing the operating system.

•For non-DOS/Windows operating systems, refer to the operating system documentation

for information on how to create a bootable diskette, formatting a drive, and installing

the operating system.

The first IDE hard disk drive you install must then be connected to the longer IDE data

cable. This is the Drive 1 position, as defined in the SETUP program.

When installing an IDE device other than a hard disk drive, connect it as follows:

•use the longer IDE data cable for a device installed in the middle shelf

•use the shorter IDE data cable for a device installed in the lower shelf.

Installing SCSI Devices

You can install up to seven SCSI devices. Up to three can be installed internally, the rest

can be installed externally. Set a unique address on each device, from 0 to 6. Make sure

addresses of internal and external devices are different. The operating system loads from

the hard disk drive with the lowest address.

A bootable SCSI hard disk is always configured with default SCSI address 0. Additional

SCSI drives may also be delivered pre-set to SCSI address 0. These drives must be

reconfigured to another SCSI address number, usually with a jumper on the drive. This must

be done to avoid addressing conflicts, as two SCSI devices cannot share the same SCSI

address number.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de De oficina de HP

HP rp5800 Manual de usuario

HP EX470 - MediaSmart Server - 512 MB RAM Cómo utilizar

HP Pavilion t600 - Desktop PC Manual de usuario

HP Compaq dx6100 Series Manual de uso y cuidado

HP Vectra VEi 7 Manual de usuario

HP Compaq D315 Manual del propietario

HP Pavilion t368 Manual de usuario

HP Z1 Manual

HP Slate21 Pro Manual de usuario

HP Pavilion d4600 - Desktop PC Hoja de especificaciones

HP Elite 7000 Microtower Manual de usuario

HP 8000f - Elite Ultra-slim Desktop PC Manual de uso y cuidado

HP Compaq Business PC dc7600 Series Instrucciones de montaje

HP DC7600 - HP Manual de usuario

HP Vectra VL6 6 Manual de usuario

HP Visualize J5000 Manual de usuario

HP 280 Pro G3 Instrucciones de instalación

HP Pavilion a1000 - Desktop PC Manual de usuario

HP 175753-002 - iPAQ - 64 MB RAM Guía de referencia rápida

HP Xw4300 - Workstation - 2 GB RAM Manual de instrucciones

HP Pavilion t227k Manual de usuario

HP 290 G2 MT Business Instrucciones de montaje

HP Spectre x360 Manual

HP Compaq Presario Manual

Manuales populares de De oficina de otras marcas

Asus

Asus E210 Series Manual de usuario

Dell

Dell Inspiron 600m Manual de usuario

Dell

Dell Inspiron 3662 Manual de usuario

TotalFlow

TotalFlow uFLO Manual de usuario

Logitech

Logitech MK320 Manual de usuario

Dell

Dell XPS 730 H2C Manual de usuario

Sony

Sony Vaio Series Manual de usuario

Sony

Sony VGC-LT32E - Vaio All-in-one Desktop Computer Manual de usuario

Alto

Alto MD 250 Manual de usuario

Lenovo

Lenovo ThinkCentre Edge 72 Manual

Lenovo

Lenovo ThinkStation D20 Manual

Arbor Technology

Arbor Technology FPC-7800 Series Manual de usuario

Sony

Sony VAIO VGX-TP1 Series Manual de usuario

Asus

Asus Eee Box B204 Manual de usuario

Dell

Dell Optiplex 9010 All In One Manual de usuario

Everex

Everex eXplora Manual de usuario

Lenovo

Lenovo ThinkCentre M75e Manual de usuario

Dell

Dell Alienware Area-51 R4 Manual de usuario