HP Intel EtherExpress PRO 10+ ISA Manual de usuario

Intel EtherExpress PRO 10+ ISA

Ethernet Adapter

Installation Guide

Notice

The information contained in this document is subject to change without notice.

Hewlett-Packard makes no warranty of any kind with regard to this

material, including, but not limited to, the implied warranties of

merchantability and fitness for a particular purpose.

Hewlett-Packard shall not be liable for errors contained herein or for incidental

or consequential damages in connection with the furnishing, performance, or use

of this material.

Hewlett-Packard assumes no responsibility for the use or reliability of its

software on equipment that is not furnished by Hewlett-Packard.

This document contains proprietary information that is protected by copyright.

All rights are reserved. No part of this document may be photocopied,

reproduced, or translated to another language without the prior written consent

of Hewlett-Packard Company.

Microsoft®, Windows® and MS-DOS® are registered trademarks of Microsoft

Corporation.

MMXTM is a trademark of Intel Corporation.

Pentium® is a registered trademark of Intel Corporation.

Hewlett-Packard France

Commercial Desktop Computing Division

38053 Grenoble Cedex 9

France

1 Installing the Intel EtherExpress PRO 10+ ISA Ethernet Adapter

Microsoft Windows 95 SR2.5

1 Installing the Intel EtherExpress PRO 10+ ISA Ethernet

Adapter

Microsoft Windows 95

SR2.5

Connecting to a

Windows NT 3.51 Server

Requirements

• HP Vectra with Windows 95 SR2.5.

• Intel EtherExpress PRO 10+ ISA Ethernet card and drivers disk.

• Microsoft Windows 95 SR2.5 media.

• Microsoft Windows NT Server 3.51 system that supports NetBEUI, TCP/

IP, NWLink IPX/SPX, and NWLink NetBIOS transfer protocols.

Device Configuration

Procedure

1With the HP Vectra turned off, install the Intel EtherExpress PRO 10+ ISA

adapter card into an ISA slot.

2Connect network cable media to the PRO 10+ card.

3Power on the machine and start Windows 95SR2.5 in MS-DOS mode.

4Insert the Intel drivers disk, “EtherExpress Ethernet Drivers” and

execute “SOFTSET2.EXE”.

5Select “CONFIGURE NIC” and verify the resource settings listed above

under the heading “Device Configuration”.

6If changes are required, save those changes and exit.

7Remove the Intel Software driver diskette and restart the system.

8When Windows 95 restarts, a message will appear to indicate that a new

hardware has been found.

Device Configuration Vectra Vli8 Vectra VEi7 Vectra VEi8

Interrupt 05 03 07

I/O Address 210 210 210

1 Installing the Intel EtherExpress PRO 10+ ISA Ethernet Adapter

Connecting to a Windows NT 3.51 Server

9Click on “Next” to continue installation then insert the Intel EtherExpress

drivers disk.

10 Click on “Other Locations…”, set the path to “A:\” and click on “Finish”.

11 When prompted for the file”EPRONDI.DLL” with the Intel EtherExpress

drivers disk inserted, set the path to “A:\” and click “OK”.

12 Click “OK” to the “Network dialog box to provide computer / workgroup

names.

13 Specify your Computer Name, Workgroup, and Computer Description. (If

you do not have the required information, contact your network

administrator).

14 Click on “Close” button, and files will copy.

15 When prompted for the file”NETAPI.DLL”, set the path to your Windows

95 files and click “OK”.

16 Click on the “Yes” button to finish the installation and restart your

computer.

2 Installing the Intel EtherExpress PRO 10+ ISA Ethernet Adapter

Microsoft Windows 95 SR2.5

2 Installing the Intel EtherExpress PRO 10+ ISA Ethernet

Adapter

Microsoft Windows 95

SR2.5

Connecting to a

Windows NT 4.0 Server

Requirements

• HP Vectra with Windows 95 SR2.5.

• Intel EtherExpress PRO 10+ ISA Ethernet card and drivers disk.

• Microsoft Windows 95 SR2.5 media.

• Microsoft Windows NT Server 4.0 system that supports NetBEUI, TCP/IP,

NWLink IPX/SPX, and NWLink NetBIOS transfer protocols.

Device Configuration

Procedure

1With the HP Vectra turned off, install the Intel EtherExpress PRO 10+ ISA

adapter card into an ISA slot.

2Connect network cable media to the PRO 10+ card.

3Power on the machine and start Windows 95SR2.5 in MS-DOS mode.

4Insert the Intel drivers disk, “EtherExpress Ethernet Drivers” and

execute “SOFTSET2.EXE”.

5Select “CONFIGURE NIC” and verify the resource settings listed above

under the heading “Device Configuration”.

6If changes are required, save those changes and exit.

7Remove the Intel Software driver diskette and restart the system.

8When Windows 95 restarts, a message will appear to indicate that a new

hardware has been found.

Device Configuration Vectra Vli8 Vectra VEi7 Vectra VEi8

Interrupt 05 03 07

I/O Address 210 210 210

2 Installing the Intel EtherExpress PRO 10+ ISA Ethernet Adapter

Connecting to a Windows NT 4.0 Server

9Click on “Next” to continue installation then insert the Intel EtherExpress

drivers disk.

10 Click on “Other Locations…”, set the path to “A:\” and click on “Finish”.

11 When prompted for the file”EPRONDI.DLL” with the Intel EtherExpress

drivers disk inserted, set the path to “A:\” and click “OK”.

12 Click “OK” to the “Network dialog box to provide computer / workgroup

names.

13 Specify your Computer Name, Workgroup, and Computer Description. (If

you do not have the required information, contact your network

administrator).

14 Click on “Close” button, and files will copy.

15 When prompted for the file”NETAPI.DLL”, set the path to your Windows

95 files and click “OK”.

16 Click on the “Yes” button to finish the installation and restart your

computer.

3 Installing the Intel EtherExpress PRO 10+ ISA Ethernet Adapter

Microsoft Windows 95 SR2.5

3 Installing the Intel EtherExpress PRO 10+ ISA Ethernet

Adapter

Microsoft Windows 95

SR2.5

Connecting to a Novell

Netware 3.12 Server

Requirements

• HP Vectra with Windows 95 SR2.5.

• Intel EtherExpress PRO 10+ ISA Ethernet card and drivers disk.

• Microsoft Windows 95 SR2.5 media.

• Novell NetWare 3.12 Server that supports NetBEUI, TCP/IP, NWLink IPX/

SPX, and NWLink NetBIOS transfer protocols.

Device Configuration

Procedure

1With the HP Vectra turned off, install the Intel EtherExpress PRO 10+ ISA

adapter card into an ISA slot.

2Connect network cable media to the PRO 10+ card.

3Power on the machine and start Windows 95SR2.5 in MS-DOS mode.

4Insert the Intel drivers disk, “EtherExpress Ethernet Drivers” and

execute “SOFTSET2.EXE”.

5Select “CONFIGURE NIC” and verify the resource settings listed above

under the heading “Device Configuration”.

6If changes are required, save those changes and exit.

7Remove the Intel Software driver diskette and restart the system.

8When Windows 95 restarts, a message will appear to indicate that a new

hardware has been found.

Device Configuration Vectra Vli8 Vectra VEi7 Vectra VEi8

Interrupt 05 03 07

I/O Address 210 210 210

3 Installing the Intel EtherExpress PRO 10+ ISA Ethernet Adapter

Connecting to a Novell Netware 3.12 Server

9Click on “Next” to continue installation then insert the Intel EtherExpress

drivers disk.

10 Click on “Other Locations…”, set the path to “A:\” and click on “Finish”.

11 When prompted for the file”EPRONDI.DLL” with the Intel EtherExpress

drivers disk inserted, set the path to “A:\” and click “OK”.

12 Click “OK” to the “Network dialog box to provide computer / workgroup

names.

13 Specify your Computer Name, Workgroup, and Computer Description. (If

you do not have the required information, contact your network

administrator).

14 Click on “Close” button, and files will copy.

15 When prompted for the file”NETAPI.DLL”, set the path to your Windows

95 files and click “OK”.

16 Click on the “Yes” button to finish the installation and restart your

computer.

4 Installing the Intel EtherExpress PRO 10+ ISA Ethernet Adapter

Microsoft Windows 95 SR2.5

4 Installing the Intel EtherExpress PRO 10+ ISA Ethernet

Adapter

Microsoft Windows 95

SR2.5

Connecting to a Novell

Netware 4.11 Server

Requirements

• HP Vectra with Windows 95 SR2.5.

• Intel EtherExpress PRO 10+ ISA Ethernet card and drivers disk.

• Microsoft Windows 95 SR2.5 media.

• Novell NetWare 4.11 Server that supports NetBEUI, TCP/IP, NWLink IPX/

SPX, and NWLink NetBIOS transfer protocols.

Device Configuration

Procedure

1With the HP Vectra turned off, install the Intel EtherExpress PRO 10+ ISA

adapter card into an ISA slot.

2Connect network cable media to the PRO 10+ card.

3Power on the machine and start Windows 95SR2.5 in MS-DOS mode.

4Insert the Intel drivers disk, “EtherExpress Ethernet Drivers” and

execute “SOFTSET2.EXE”.

5Select “CONFIGURE NIC” and verify the resource settings listed above

under the heading “Device Configuration”.

6If changes are required, save those changes and exit.

7Remove the Intel Software driver diskette and restart the system.

8When Windows 95 restarts, a message will appear to indicate that a new

hardware has been found.

Device Configuration Vectra Vli8 Vectra VEi7 Vectra VEi8

Interrupt 5 03 07

I/O Address 210 210 210

4 Installing the Intel EtherExpress PRO 10+ ISA Ethernet Adapter

Connecting to a Novell Netware 4.11 Server

9Click on “Next” to continue installation then insert the Intel EtherExpress

drivers disk.

10 Click on “Other Locations…”, set the path to “A:\” and click on “Finish”.

11 When prompted for the file”EPRONDI.DLL” with the Intel EtherExpress

drivers disk inserted, set the path to “A:\” and click “OK”.

12 Click “OK” to the “Network dialog box to provide computer / workgroup

names.

13 Specify your Computer Name, Workgroup, and Computer Description. (If

you do not have the required information, contact your network

administrator).

14 Click on “Close” button, and files will copy.

15 When prompted for the file”NETAPI.DLL”, set the path to your Windows

95 files and click “OK”.

16 Click on the “Yes” button to finish the installation and restart your

computer.

Este manual sirve para los siguientes modelos

Otros manuales de De oficina de HP

HP Z230 SFF Workstation Manual

HP EliteDesk 705 G2 Small Form Factor Manual

HP Deskpro 4000 Documento técnico

HP i2000 Manual

HP Compaq CQ2009F Manual de usuario

HP IQ524 - TouchSmart - 4 GB RAM Manual de usuario

HP TouchSmart Elite 7320 Manual de usuario

HP Z420 Series Manual de usuario

HP P6240f - Pavilion - 8 GB RAM Manual de usuario

HP 744 Manual de usuario

HP Vectra VL410 Manual de usuario

HP dx7380 - Microtower PC Instrucciones de uso

HP Media Center m7200 - Desktop PC Guía de inicio rápido

HP Vectra VL410 Manual de usuario

HP TouchSmart IQ700 - Desktop PC Instrucciones de funcionamiento

HP Compaq dc7900 Business PC Manual de usuario

HP Brio BAx Manual

HP Net Vectra Manual de usuario

HP Compaq Presario Hoja de especificaciones

HP dc5100 - Microtower PC Manual de uso y mantenimiento

HP EliteDesk 800 G3 Manual de usuario

HP Workstation x1100 Manual de usuario

HP Media Center Instrucciones de montaje

HP Visualize c3600 Guía de inicio rápido

Manuales populares de De oficina de otras marcas

Asus

Asus E210 Series Manual de usuario

Dell

Dell Inspiron 600m Manual de usuario

Dell

Dell Inspiron 3662 Manual de usuario

TotalFlow

TotalFlow uFLO Manual de usuario

Logitech

Logitech MK320 Manual de usuario

Dell

Dell XPS 730 H2C Manual de usuario

Sony

Sony Vaio Series Manual de usuario

Sony

Sony VGC-LT32E - Vaio All-in-one Desktop Computer Manual de usuario

Alto

Alto MD 250 Manual de usuario

Lenovo

Lenovo ThinkCentre Edge 72 Manual

Lenovo

Lenovo ThinkStation D20 Manual

Arbor Technology

Arbor Technology FPC-7800 Series Manual de usuario

Sony

Sony VAIO VGX-TP1 Series Manual de usuario

Asus

Asus Eee Box B204 Manual de usuario

Dell

Dell Optiplex 9010 All In One Manual de usuario

Everex

Everex eXplora Manual de usuario

Lenovo

Lenovo ThinkCentre M75e Manual de usuario

Dell

Dell Alienware Area-51 R4 Manual de usuario