HP Compaq Business Desktop dc7100 Series Instrucciones de montaje

HP-00007-01, Appendix 3 18-Aug-2005

HP Restricted

Page 1

Appendix 3 Product End-of-Life Disassembly instructions – rev a

Product Identification:

Marketing Name / Model Description

HP Compaq Business Desktop dc7100 Series - SFF HP business desktop PC – Small Form Factor

chassis

Purpose: The document is intended for use by end-of-life recyclers or treatment facilities. It provides the

basic instructions for the disassembly of HP products to remove components and materials requiring

selective treatment.

1.0 Items Requiring Selective Treatment

1.1 Items listed below are classified as requiring selective treatment.

1.2 Enter the quantity of items contained within the product which require selective treatment in

the right column, as applicable.

Item Description

Notes

Qty items in

product.

Printed Circuit Boards (PCB) or Printed

Circuit Assemblies (PCA)

With a surface greater than 10

square cm

2 (sys bd, power

supply PCA)

Batteries All types including standard

alkaline and lithium coin or button

style batteries

Mercury containing components For example, mercury in lamps,

display backlights, scanner lamps,

switches, batteries

Liquid Crystal Displays (LCD) with a

surface greater than 100 square cm

Includes background illuminated

displays with gas discharge lamps

Cathode Ray Tubes (CRT)

Capacitors / condensers (Containing

PCB / PCT)

Electrolytic Capacitors / Condensers

measuring greater than 2.5 cm in

diameter or height

External electrical cables and cords PSU, IDE, SATA cables.

Gas Discharge Lamps

Plastics containing Brominated Flame

Retardants

1 – power

supply fan

Components and parts containing toner

and ink, including liquids, semi-liquids

(gel/paste) and toner

Include the cartridges, print

heads, tubes, vent chambers, and

service stations.

Components and waste containing

asbestos

Components, parts and materials

containing refractory ceramic fibers

Components, parts and materials

containing radioactive substances

HP-00007-01, Appendix 3 18-Aug-2005

HP Restricted

Page 2

2.0 Tools Required

List the type and size of the tools that would typically be used to disassemble the product to a

point where components and materials requiring selective treatment can be removed.

Tool Description Tool Size (if applicable)

Flat blade screwdriver

Phillips screwdriver

Diagonal cutters (dikes)

3.0 Product Disassembly Process

3.1 List the basic steps that should typically be followed to remove components and materials

requiring selective treatment:

SYSTEM BOARD

1 To remove the computer cover (see Figure 1 below):

a) Press the buttons on the left and right sides of the computer.

b) Slide the computer cover toward the front of the computer until it stops, and then lift the

cover up and off the chassis.

2 Remove all expansion cards from the system board.

3 Lift up on the fan shroud to remove it from the chassis (see Figure 2 below).

4 Slide the drive tray forward and disconnect the drive and power cables from the system

board (see Figure 3 below).

5 If applicable, remove the security clip (see Figure 4 below).

NOTE: The security clip is an optional feature and is not installed on all computers.

6 Rotate the power supply to its upright position (see Figure 5 below).

7 Disconnect the serial port from the system board (see Figure 6 below).

8 Disconnect any remaining cables from the system board.

9 Remove the long mounting screw that secures the system board tray to the chassis

(see Figure 7 below).

10 Slide the system board tray assembly towards the front of the chassis, about 1/4 inch, and

then lift the system board up and out of the chassis (see Figure 8 below).

BATTERY

Locate the battery and battery holder on the system board. Depending on the type of battery

holder on the system board, complete the following instructions to remove the battery:

TYPE 1 BATTERY HOLDER (see Figure 9 below)

Lift the battery out of the holder.

HP-00007-01, Appendix 3 18-Aug-2005

HP Restricted

Page 3

TYPE 2 BATTERY HOLDER (see Figure 10 below)

To release the battery from its holder, squeeze the metal clamp that extends above one edge of

the battery. When the battery pops up, lift it out.

TYPE 3 BATTERY HOLDER (see Figure 11 below)

Pull back on the clip that holds the battery in place, and then remove the battery.

POWER SUPPLY

1 Remove the security clip (see Figure 4 below).

NOTE: The security clip is an optional feature and is not installed on all computers.

2 Rotate the power supply to its upright position.

3 Pull the drive cage forward and disconnect the power cables from all of the drives.

4 Release the power supply cable from the cable retaining clip at the front of the chassis

below the drive cage and from the clip on the side of the chassis in front of the hard drive.

5 If required, remove the sensor from the power supply by sliding the hood sensor switch

mounted on the power supply toward the outside of the computer and lowering it through

the slot (see Figure 12 below).

NOTE: The hood sensor is an optional feature and is not installed on all computers.

6 Lift the power supply up and out of the chassis (see Figure 13 below).

POWER SUPPLY PRINTED CIRCUIT ASSEMBLY

1 Remove all screws that secure the covers to the power supply chassis. Depending on the

power supply, you must remove either two or three separate pieces

(see Figures 14 & 15 below).

NOTE: Power supply screw quantity and location may vary.

2 Snip the plastic cable clamp that secures the main wires to the power supply chassis

(see Figure 16 below).

3 Lift the top cover off the power supply. Note that there either may be tabs on the back of

the cover that hinge into the power supply chassis, or tabs on the top of the cover that you

must depress to release the cover.

4 Remove the back panel. Note that there may be tabs that hinge into the power supply

chassis.

5 If applicable, remove the side panel.

6 Using a pair of diagonal cutters (dikes), cut the following wires (see Figure 17 below):

•black power connector wire

•thick black fan wire (Note: You can unplug this wire instead of cutting it).

•main collection of wires – to gain access to the capacitors

HP-00007-01, Appendix 3 18-Aug-2005

HP Restricted

Page 4

POWER SUPPLY PRINTED CIRCUIT ASSEMBLY cont

7 Remove the screws that secure the printed circuit assembly to the power supply chassis

(see Figure 18 below), and then lift the PCA out of the chassis.

NOTE: Screw quantity and location may vary.

POWER SUPPLY FAN

1 Remove the four screws that secure the fan to the power supply (see Figure 19 below).

2 Lift the fan out of the power supply.

3.2 ILLUSTRATIONS

FIGURE 1: Removing the computer cover

FIGURE 2: Removing the fan shroud

FIGURE 3: Disconnecting the drive and power

cables from the system board

FIGURE 4: Removing the security clip

HP-00007-01, Appendix 3 18-Aug-2005

HP Restricted

Page 5

FIGURE 5: Rotating the power supply to its

upright position

FIGURE 6: Disconnecting the serial port from

the system board

FIGURE 7: Removing the mounting screw

from the system board

FIGURE 8: Removing the system board from

the chassis

HP-00007-01, Appendix 3 18-Aug-2005

HP Restricted

Page 6

FIGURE 9: Type 1 battery holder

FIGURE 10: Type 2 battery holder

FIGURE 11: Type 3 battery holder

FIGURE 12: Removing the hood sensor

HP-00007-01, Appendix 3 18-Aug-2005

HP Restricted

Page 7

FIGURE 13: Removing the power supply

FIGURE 14: Power supply screw locations

(may vary)

FIGURE 15: Power supply screw locations

(may vary)

FIGURE 16: Cut plastic cable clamp

HP-00007-01, Appendix 3 18-Aug-2005

HP Restricted

Page 8

FIGURE 17: Cut wires (may vary)

FIGURE 18 PCA screw locations (may vary)

FIGURE 19: Power supply fan screw locations

Otros manuales para Compaq Business Desktop dc7100 Series

Tabla de contenidos

Otros manuales de De oficina de HP

HP Compaq dx2818 Microtower Manual de operación y mantenimiento

HP Pavilion a200 - Desktop PC Manual de usuario

HP EliteDesk 800 G5 Instrucciones de instalación

HP Kayak XU04 Manual de usuario

HP Evo D510 e-pc Manual del producto

HP ProDesk 405 G2 Manual de usuario

HP Z800 - Workstation - 6 GB RAM Manual de usuario

HP Compaq 6000 Pro SFF Manual de operación y mantenimiento

HP Compaq Presario Manual de usuario

HP Z200 - Small Form Factor Workstation Manual de usuario

HP Pavilion t600 - Desktop PC Manual de usuario

HP Pavilion 525 Instrucciones de instalación

HP Pavilion a700 - Desktop PC Instrucciones de instalación

HP Neoware e370 - Thin Client Manual de usuario

HP Rp3000 - Point of Sale System Guía de configuración

HP EliteDesk 705 G5 Manual

HP A1210n - Pavilion - 512 MB RAM Guía de inicio rápido

HP Pavilion xg900 - Desktop PC Manual

HP Pavilion v400 - Desktop PC Manual de usuario

HP Pavilion t482k Manual de usuario

HP 9000 Series 319C+ Cómo utilizar

HP Compaq Presario CQ5000 PC Series Instrucciones de instalación

HP Compaq Presario Manual de usuario

HP M9402f - pavilion - elite Manual de usuario

Manuales populares de De oficina de otras marcas

Asus

Asus E210 Series Manual de usuario

Dell

Dell Inspiron 600m Manual de usuario

Dell

Dell Inspiron 3662 Manual de usuario

TotalFlow

TotalFlow uFLO Manual de usuario

Logitech

Logitech MK320 Manual de usuario

Dell

Dell XPS 730 H2C Manual de usuario

Sony

Sony Vaio Series Manual de usuario

Sony

Sony VGC-LT32E - Vaio All-in-one Desktop Computer Manual de usuario

Alto

Alto MD 250 Manual de usuario

Lenovo

Lenovo ThinkCentre Edge 72 Manual

Lenovo

Lenovo ThinkStation D20 Manual

Arbor Technology

Arbor Technology FPC-7800 Series Manual de usuario

Sony

Sony VAIO VGX-TP1 Series Manual de usuario

Asus

Asus Eee Box B204 Manual de usuario

Dell

Dell Optiplex 9010 All In One Manual de usuario

Everex

Everex eXplora Manual de usuario

Lenovo

Lenovo ThinkCentre M75e Manual de usuario

Dell

Dell Alienware Area-51 R4 Manual de usuario