HP 86H1880 Manual de usuario

PCI Wake on LAN Token Ring Adapter

86H1880

Installation Guide

All manuals and user guides at all-guides.com

all-guides.com

Notice

The information contained in this document is subject to change without notice.

Hewlett-Packard makes no warranty of any kind with regard to this material,

including, but not limited to, the implied warranties of merchantability and

fitness for a particular purpose.

Hewlett-Packard shall not be liable for errors contained herein or for incidental

or consequential damages in connection with the furnishing, performance, or use

of this material.

Hewlett-Packard assumes no responsibility for the use or reliability of its

software on equipment that is not furnished by Hewlett-Packard.

This document contains proprietary information that is protected by copyright.

All rights are reserved. No part of this document may be photocopied,

reproduced, or translated to another language without the prior written consent

of Hewlett-Packard Company.

Microsoft®, Windows® and MS-DOS® are registered trademarks of Microsoft

Corporation.

MMXTM is a trademark of Intel Corporation.

Pentium® is a registered trademark of Intel Corporation.

Hewlett-Packard France

Commercial Desktop Computing Division

38053 Grenoble Cedex 9

France

All manuals and user guides at all-guides.com

1 Connecting to a Netware 3.12 Server

Windows for Workgroups

1 Connecting to a Netware 3.12 Server

Windows for

Workgroups

Requirements

• HP Vectra with DOS and MS-Windows for Workgroups 3.11 installed.

• IBM Token-Ring 16/4 PCI adapter and drivers CD ver 1.

• Driver Name: IBMTRPO.LAN Size: 65KB Date: 7/26/96

• Novell Netware server that supports Net BEUI, NWLink IPX/SPX, and

NWLink NetBIOS transfer protocols.

Device Configuration

Procedure

1Boot the Vectra to a DOS prompt, and insert the IBM Token-Ring 16/4 PCI

adapter and drivers CD ver 1.

2VE7/VE8: From the "IBMTRPCI\LANAID\" directory on your CD-ROM

type "LANAIDC/VIEW" to verify the deice configuration settings. VL8 and

VE7/VE8: From the “IBMWOL\IBMTRPCI\LANAID\” directory on your

CD-ROM run “LANAID.EXE.”

3Hit enter for “Software Installation” and verify the following options:

4DOS with Windows v3.1x

5Express Install LAN Client’s NetWare Client & 802.2

6Hit enter to continue, and at the “Express Install of IBM LAN Client”

window, hit enter to install.

7After file copy is complete, remove any diskettes, hit enter four times to

exit, then reboot the computer.

8After Windows loads, open the “Netware User Applications” window, and

Vectra VL8 Vectra VE7/VE8

Interrupt 11 10(11)

I/O Address C800-h DC00h

Card State - Enabled

All manuals and user guides at all-guides.com

1 Connecting to a Netware 3.12 Server

Windows for Workgroups

double-click the “NetWare User Login” icon.

9Login into the current server to verify connection.

(If you do not have the required information to Login, contact your system

administrator)

All manuals and user guides at all-guides.com

1 Connecting to a Netware 3.12 Server

Windows 95 SR2

Windows 95 SR2 Requirements

• HP Vectra with Windows 95SR2 installed.

• IBM Token-Ring 16/4 PCI adapter and drivers CD ver 1.2

• Driver Name for Vectra VL8: W95SETUP.INF Size: 8K Date: 10/18/96

• Driver Name for Vectra VE7/VE8: OEMSETUP.INF Size: 65K Date: 08/05/

97.

• Novell Netware server that supports Net BEUI, NWLink IPX/SPX, and

NWLink NetBIOS transfer protocols.

Device Configuration

Procedure

1With the HP Vectra turned off, install the IBM 16/4 PCI TR adapter card

into a PCI slot.

2Boot the machine to Windows 95, and the Token-Ring card will

automatically be recognized. Click on “Next.”

3When prompted, click on “Other Locations.”

4Insert drivers CD, set the path to “D:\WIN95\” (Where “D” is the drive

letter assigned to your CD-ROM) and click “OK.”

(If you have an HP preloaded HDD, set the path to “C:\MASTERS\LAN

\TRPCI.WOL\WIN95\”)

5Click on “OK” to continue the installation.

6Verify that “IBM PCI Token-Ring Adapter, NDIS2/3” is listed and click on

“Finish.”

7Click “OK” to provide your Computer and Workgroup names.

8Enter your Computer Name, Workgroup Name, Computer Description,

and click on “Close.”

Vectra VL8 Vectra VE7/VE8

Card State - Enabled

Interrupt 11 10(5)

I/O Address C800-h DC00-h

All manuals and user guides at all-guides.com

1 Connecting to a Netware 3.12 Server

Windows 95 SR2

9When prompted for the “IBM PCI Token-Ring Option Diskette” click on

“OK.”

10 In the “Copying Files…” dialogue box, set the path to “D:\DOS\” (Where

“D” is the drive letter assigned to your CD-ROM) and click “OK.”

(If you have an HP preloaded HDD, set the path to “C:\MASTERS\LAN

\TRPCI.WOL\DOS\”)

11 When prompted for the file “IBMTRP.VXD”, set the path to “D:\WIN95\”

(Where “D” is the drive letter assigned to your CD-ROM) and click “OK.”

(If you have an HP preloaded HDD, set the path to “C:\MASTERS\LAN

\TRPCI.WOL\WIN95\”)

12 When prompted to insert the Windows 95 CD-ROM, click on “OK.”

13 Set the path to your Windows 95 files and click on “OK.”

(If you have an HP pre-loaded HDD, set the path statement

C:\MASTERS\WIN95\SYSTEM\CABS\”).

14 Click on “Yes” to restart your computer and finish the installation.

All manuals and user guides at all-guides.com

all-guides.com

2 Connecting to a Netware 4.11 Server

Windows for Workgroups

2 Connecting to a Netware 4.11 Server

Windows for

Workgroups

Requirements

• HP Vectra with DOS and MS-Windows for Workgroups 3.11 installed.

• IBM Token-Ring 16/4 PCI adapter and drivers CD ver 1.

• Driver Name: IBMTRPO.LAN Size: 65KB Date: 7/26/96

• Novell Netware server 4.1 that supports Net BEUI, NWLink IPX/SPX, and

NWLink NetBIOS transfer protocols.

Device Configuration

Procedure

1Boot the Vectra to a DOS prompt, and insert the IBM Token-Ring 16/4 PCI

adapter and drivers CD ver 1.

2From the “IBMWOL\IBMTRPCI\LANAID\” directory on your CD-ROM run

“LANAID.EXE.”

3Hit enter for “Software Installation” and verify the following options:

4DOS with Windows v3.1x

5Express Install LAN Client’s NetWare Client & 802.2

6Hit enter to continue, and at the “Express Install of IBM LAN Client”

window, hit enter to install.

7After file copy is complete, remove any diskettes, hit enter four times to

exit, then reboot the computer.

8After Windows loads, open the “Netware User Applications” window, and

double-click the “NetWare User Login” icon.

9Login into the current server to verify connection.

Vectra VL8 Vectra VE7/VE8

Card State - Enabled

Interrupt 11 10(11)

I/O Address C800-h DC00-h

All manuals and user guides at all-guides.com

2 Connecting to a Netware 4.11 Server

Windows for Workgroups

(If you do not have the required information to Login, contact your system

administrator)

All manuals and user guides at all-guides.com

2 Connecting to a Netware 4.11 Server

Windows 95 SR2

Windows 95 SR2 Requirements

• HP Vectra with Windows 95SR2 installed.

• IBM Token-Ring 16/4 PCI adapter and drivers CD ver 1.2

• Driver Name: W95SETUP.INF Size: 8K Date: 10/18/96

• Novell Netware 4.1 server that supports Net BEUI, NWLink IPX/SPX, and

NWLink NetBIOS transfer protocols.

Device Configuration

Procedure

1With the HP Vectra turned off, install the IBM 16/4 PCI TR adapter card

into a PCI slot.

2Boot the machine to Windows 95, and the Token-Ring card will

automatically be recognized. Click on “Next.”

3When prompted, click on “Other Locations.”

4Insert drivers CD, set the path to “D:\WIN95\” (Where “D” is the drive

letter assigned to your CD-ROM) and click “OK.”

(If you have an HP preloaded HDD, set the path to “C:\MASTERS\LAN

\TRPCI.WOL\WIN95\”)

5Click on “OK” to continue the installation.

6Verify that “IBM PCI Token-Ring Adapter, (NDIS2/3)” is listed and click

on “Finish.”

7Click “OK” to provide your Computer and Workgroup names.

8Enter your Computer Name, Workgroup Name, Computer Description,

and click on “Close.”

9When prompted for the “IBM PCI Token-Ring Option Diskette” click on

“OK.”

Vectra VL8 Vectra VE7/VE8

Card State - Enabled

Interrupt 11 10(5)

I/O Address C800-h DC00-h

All manuals and user guides at all-guides.com

2 Connecting to a Netware 4.11 Server

Windows 95 SR2

10 In the “Copying Files…” dialogue box, set the path to “D:\DOS\” (Where

“D” is the drive letter assigned to your CD-ROM) and click “OK.”

(If you have an HP preloaded HDD, set the path to “C:\MASTERS\LAN

\TRPCI.WOL\DOS\”)

11 When prompted for the file “IBMTRP.VXD”, set the path to “D:\WIN95\”

(Where “D” is the drive letter assigned to your CD-ROM) and click “OK.”

(If you have an HP preloaded HDD, set the path to “C:\MASTERS\LAN

\TRPCI.WOL\WIN95\”)

12 When prompted to insert the Windows 95 CD-ROM, click on “OK.”

13 Set the path to your Windows 95 files and click on “OK.”

(If you have an HP pre-loaded HDD, set the path statement

C:\MASTERS\WIN95\SYSTEM\CABS\”).

14 Click on “Yes” to restart your computer and finish the installation.

All manuals and user guides at all-guides.com

Tabla de contenidos

Otros manuales de Adaptador de HP

HP A6826A Manual de usuario

HP 366T Manual de usuario

HP 70590A Manual

HP XP Manual de usuario

HP 652503-B21 Manual de usuario

HP P3410A - NetRAID 1M RAID Controller Hoja de instrucciones

HP ScanJet 100 Manual de usuario

HP StorageWorks A7298A Manual de usuario

HP NC364m Instrucciones de uso

HP 41802A Guía de inicio rápido

HP 570FLR-SFP Manual de usuario

HP Model 744 - VME Workstation Instrucciones de instalación y mantenimiento

HP 665240-B21 Manual de usuario

HP Ethernet 10Gb 2-port 530T Adapter Manual de usuario

HP StoreFabric CN1100R Manual de usuario

HP NC370F Manual de usuario

HP 629135-B21 Manual de usuario

HP NC7170 Manual de usuario

HP A4800A Manual de usuario

HP Nc551m Instrucciones de uso

HP VL600 - Vectra - 128 MB RAM Manual de usuario

HP 90W Manual de usuario

HP 728987-B21 Manual de usuario

HP NC373F Instrucciones de uso

Manuales populares de Adaptador de otras marcas

PCB Piezotronics

PCB Piezotronics 090B274 Manual de usuario

Auvidea

Auvidea J20 Manual del producto

Gossen MetraWatt

Gossen MetraWatt AT3-III E Manual de usuario

Akribis

Akribis ITF-21-BISS-MIT Manual de usuario

Tenda

Tenda W54U Manual de usuario

ROHO

ROHO AGILITY Manual de usuario

PROLiNK

PROLiNK WN2001 Manual de usuario

Hawking

Hawking HUF2 Manual de usuario

Airlink101

Airlink101 AWLC4030 Manual de usuario

NETGEAR

NETGEAR XAV101v1 - Powerline AV Ethernet Adapter Manual de usuario

Philips

Philips SWA4554S/10 Manual de usuario

JVC

JVC TS-C9D2B Manual de instrucciones

NETGEAR

NETGEAR A6100 Manual de usuario

D-Link

D-Link DWA-121 Manual de usuario

Philips

Philips SWA2037 Manual de usuario

Basalte

Basalte 0610-20 Manual de usuario

Yealink

Yealink EHS40 Manual de usuario

Balluff

Balluff BIC 1B0-IT1A7-Q40KFU-SM4A4A Manual de usuario