Hotpoint FFU00 Manual de usuario

User Instructions

for Model

FFU00

If you have damaged the existing lead or require a longer one a charge will be made. It is

strongly advised that this work is carried out by a qualified electrician.

CE marking certifies that this appliance conforms to the following EEC directives:-

Low Voltage Equipment - 72/23/EEC & 93/68 EEC

Electromagnetic Compatibility - 89/336/EEC, 92/31/EEC & 93/68/EEC

Electrical Supply

WARNING: This appliance must be earthed.

Fuses

Your appliance comes fitted with a plug and a 13A fuse.

If you need to replace the fuse, only those rated at 13A and ASTA

approved to BS1362 should be used.

WARNING: Do not use the plug unless the fuse cover is fitted.

Changing the Mains Lead

A special lead can be ordered from your Service Department:

UK: 08709 066 066 or

Republic of Ireland: 1850 302 200

Changing the plug

Cut off and dispose of the supplied plug if it does not fit your socket.

WARNING: To avoid a shock hazard do not insert the discarded plug into a socket anywhere

else.

IMPORTANT: WIRES IN THE MAINS LEAD ARE COLOURED IN ACCORDANCE WITH THE

FOLLOWING CODE:

Green and yellow (Earth) wire to

terminal marked ‘E’, symbol ,

or coloured green and yellow.

Blue (Neutral) wire to terminal

marked ‘N’ or coloured black. Cord

clamp

13A ASTA approved fuse

to BS1362.

Brown (Live) wire to

terminal marked ‘L’ or

coloured red.

Green / Yellow - Earth

Blue - Neutral

Brown - Live

If you change the plug, the colour of

the wires in the mains lead may not

correspond with the colour of the

markings identifying terminals in the

plug. You should therefore wire it as

shown.

Retention of the instruction Book

This instruction Book must be kept handy for reference as it contains important details on

the safe and proper use of the appliance.

If you sell or pass the appliance to someone else, or move house and leave it behind, make

sure this Book is also provided so the new owner can become familiar with the appliance

and safety warnings.

Contents Page

Electrical requirement 2

Safety advice 4

Installation 5-10

Get to know your Appliance 11-13

The controls 14-16

Storing food 17-18

Care & Cleaning 19

Troubleshooting 20-24

Guarantee 26

Recycling & Disposal information 26

After sales service 27

Key contacts back cover

* Please take time to read this booklet

before installing and switching on this

appliance.The manufacturer assumes

no responsibility for incorrect

installation and usage.

* If this appliance is to replace an old

refrigerator with a lock, break or remove

the lock as a safety measure to avoid the

danger of children playing with the

refrigerator and locking them inside.

* Old refrigerators and freezers contain

insulation gases and refrigerant that must

be disposed of properly. Please ensure that

none of the tubing at the back of the

appliance gets damaged.

* Do not twist and bend the mains lead and

keep it away from hot surfaces.

* Do not let children play with the appliance.

* Do not sit or stand on the appliance.

* Do not use sharp metal objects for

removing any ice build up in the freezer

compartment, as this could cause damage

to the refrigeration system.

* Do not put the plug into the power supply

with wet hands.

* Do not store poisonous, flammable or

dangerous substances in your freezer.

* Do not store carbonated (fizzy) drinks or

medicines in the freezer compartment.

* Do not eat iced lollipops or other such

things direct from the freezer

compartment as this could cause low

temperature skin burns, always leave

for a few minutes before eating.

* Do not touch the surfaces inside the

freezer compartment with wet hands as

this could cause low temperature skin

burns.

* Do not use aerosol sprays for defrosting or

cleaning your appliance.

Safety advice

Before Fitting:

Please read through this section before

starting any work.

Choosing a Location:

Do not install your appliance in a room where

the temperature goes below 5˚C, this will

affect the appliances performance.

The power socket should be in a readily

accessible position, adjacent to the appliance.

DO NOT connect to the electricity supply until

all installation is complete.

Place the appliance in a dry and regularly

ventilated room.

Never place the appliance near heat emitting

devices (eg. cooker, radiator, water heater or

similar devices) and do not expose it to direct

sunlight. In such a position your appliance

will have to work harder and will cost more to

run and could be damaged by the heat.

Ensure that you provide adequate air

circulation around the appliance, to prevent

condensation.

Leave at least 300mm free space above and

50mm or more from the wall.

Also, the appliance should be elevated 25mm

from the floor, especially if it is carpeted.

Providing you follow the recommended

ventilation requirements you will:

* Prolong the life of your appliance.

* Minimise the risk of condensation on the

outside of the appliance.

* Minimise the running costs.

* Minimise operating sounds caused by

vibration.

Door Removal:

If your access door is too narrow for the

appliance to pass through, you will need to

remove both doors - pass the appliance

through the access door, in its upright

position - then refit the doors on the other

side (see Door Removal instructions - pages 6

& 7).

Water Supply:

Your appliance has an ice maker and cool

water dispenser function and therefore needs

to be connected to a cold water supply before

use (see Feed Water Tube / Plumbing

Installation instructions - page 8 and 9).

Levelling

Level both doors by adjusting the left and

right hand height adjusting screws.

With the doors aligned they will close

correctly and this helps the appliance to run

efficiently (see Height Adjustment instructions

- page 10)

Installation

WARNING: THE APPLIANCE SHOULD

ONLY BE INSTALLED BY A QUALIFIED

PERSONNEL IN COMPLIANCE WITH THESE

INSTRUCTIONS, CURRENT STANDARDS

AND REGULATIONS.

You may need to remove both doors for the

appliance to fit through access doors -

follow the instructions below:

Feed Water Tube:

* Remove the lower cover by lifting upwards.

* Pull out the feed water tube, while pressing

area (1) indicated in Fig.1

Remove the Freezer Compartment Door:

* Loosen the screws in the upper hinge

cover and remove. Separate all connection

wires, except for the earth line (Fig.2).

* Remove the retainer by rotating it anti-

clockwise (a- Fig.3), then remove the

upper hinge by lifting up.

* Remove the freezer compartment door by

lifting it up off the lower hinge.

Lift enough so that the feed water tube is

completely pulled out (Fig.4)

Installation

WARNING: ENSURE THE APPLIANCE IS NOT

CONNECTED TO THE ELECTRICITY SUPPLY

BEFORE INSTALLING.

WARNING: YOU MAY NEED ASSISTANCE TO

DO THIS - THE DOORS ARE HEAVY AND

SHOULD BE SUPPORTED AT ALL TIMES TO

AVOID DAMAGE AND INJURY.

NOTE: Cut away any tube end which is

misshapen or worn

NOTE: Support the door when removing

the upper hinge.

NOTE: Carry the freezer compartment

door through the access door and lay it

down on suitable material eg. the original

packaging.

Take care not to bend or damage the feed

water tube.

Fig.1

Fig.2

Fig.3

Fig.4

Remove the Fridge Compartment Door:

* Loosen the upper hinge cover screws and

remove the cover (Fig.5).

* Remove the retainer by rotating it

clockwise (b- Fig.6), then remove the

upper hinge by lifting up.

* Remove the fridge compartment door by

lifting it up, off the lower hinge (Fig.7).

Pass the appliance through the access door,

in its upright position (Fig.8)

Door Replacement:

* Replace both doors by following the

removal instruction in reverse order.

Installation

NOTE: Support the door when removing

the upper hinge.

NOTE: Carry the fridge compartment door

through the access door and lay it down

on suitable material eg. the original

packaging.

Fig.5

Fig.6

Fig.7

Fig.8

●

FIRST CHECK YOU HAVE THE CORRECT

ITEMS:

- Pipe / Filter Kit comprises:

* 1 x Water Filter

* 2 x Self-Adhesive Fixing Plates

* 2 x Cable Ties

* 1 x 10m Water Pipe

- Adaptor Kit comprises:

* Plastic Pipe Connector

* Rubber Washer

* Threaded Tap Connector

●

NEXT, HAVE A LOOK AT THE DIAGRAM

BELOW TO VISUALISE HOW THE

APPLIANCE SHOULD BE CONNECTED:

Installation

Fridge

Filter

Water Pipe Water Pipe Tap

●

Connection to the Appliance:

* At the back of the

appliance you will see

the water inlet valve

(Fig.A)

* You now need to cut the water pipe to the right length for the

connection of the water filter.

It is suggested that approximately 1.5m of pipe is used - this

should allow the filter to be located in an easily accessible

position (as the water filter should be replaced approximately

every 6 months, according to use and conditions) and also allow

some slack in the pipe behind the appliance, so that it can be

pulled out for cleaning or servicing purposes.

You must also ensure that the cut is square and not at any

sort of angle as this could cause a leak.

* Unscrew the metal

threaded collar and

place it over one end of

the water pipe (Fig.B)

* Push the water pipe

onto the water inlet

valve firmly, tighten up

the metal collar (Fig.C)

✓

✗

Installation

●

FINALLY: Plug in and switch on the electricity supply. Turn on the water supply tap.

Check for any leaks. Ensure selection is set to ‘water’ (see page 15) push a cup under

the dispenser to verify that water is flowing. When all working OK, move the appliance

into its final location - your appliance is heavy and care should be taken when moving

it, also do not trap or kink hoses at the back of the appliance. Replace the lower cover.

Mount the water filter in an accessible position using the self-adhesive fixing plates

and cable ties supplied.

●

Connection of Water Filter:

●

Connection to the Water Tap:

* Unscrew the threaded connector and

place it over the end of the cut

section of pipe coming away from

the appliance. Push the pipe over the

end of the water filter that the arrow

points to and tighten the threaded

connector (Fig.D)

* Cut the pipe that is connected to the water filter to the

correct length. Again, make sure that the cut is nice and

square to avoid leaks.

* Push the pipe into the smaller hole of the connector

supplied in the adaptor kit. The pipe should be held

firm (Fig.F)

* Place the threaded tap connector over the long part of

the brass flange. Firmly push the flange into the other

end of the water connector (Fig.G)

* Place the rubber washer inside the threaded tap

connector and screw onto the water tap.

* Repeat on the other end of the water

filter, using the remainder of water

pipe (Fig.E)

* Run this section of water pipe from

the water filter to the water supply

tap, making sure it is not trapped or

kinked at all.

Note the direction markings on the filter

* Now you have to cut the pipe to the length it needs to be to run from the back of the

appliance and attach to the water filter.

NOTE: The water filter is marked with an arrow to show the direction of water flow (ie. from

supply tap to appliance).

Remember however, that the connection process is being done FROM the appliance TO the

tap (ie.in reverse of the water flow when in use).

Height Adjustment:

Levelling both doors using the height

adjustment screws. With the doors level they

will close smoothly.

If the doors do not close correctly it will affect

the performance of your appliance.

* If the freezer compartment door is lower

than the fridge compartment door, adjust

the left hand adjustment screw (Fig.10).

Level the door by inserting a flat (- type)

driver into the groove of the left hand

adjustment screw and rotate it clockwise.

* If the freezer compartment door is higher

than the fridge compartment door, adjust

the right hand adjustment screw (Fig.11).

Level the door by inserting a flat (- type)

driver into the groove of the right hand

adjustment screw and rotate it clockwise.

Installation

Fig.10

Fig.11

Tabla de contenidos

Otros manuales de Refrigerador de Hotpoint

Hotpoint

Hotpoint HMB312AAI Manual de usuario

Hotpoint

Hotpoint ENTMH 19 FW Series Manual de usuario

Hotpoint

Hotpoint HTS16BBS - 15.7 cu. Ft. Top-Freezer... Manual de usuario

Hotpoint

Hotpoint FFA45W Manual de usuario

Hotpoint

Hotpoint HTR16BBSL Manual

Hotpoint

Hotpoint ENXTYH 19 FW Series Manual de usuario

Hotpoint

Hotpoint XEX95 Series Manual de usuario

Hotpoint

Hotpoint HM 3x AA Manual de usuario

Hotpoint

Hotpoint FF200LG Manual de usuario

Hotpoint

Hotpoint HTR15BBM Instrucciones de uso

Hotpoint

Hotpoint HTR17BBSL Manual

Hotpoint

Hotpoint 16 Instrucciones de funcionamiento

Hotpoint

Hotpoint HTS22GBP Manual de usuario

Hotpoint

Hotpoint FF Series Manual de usuario

Hotpoint

Hotpoint HTS18BBPRCC Instrucciones de montaje

Hotpoint

Hotpoint Quadrio 4D Series Manual de usuario

Hotpoint

Hotpoint FFA97 Manual de usuario

Hotpoint

Hotpoint NCD 191 I Manual de usuario

Hotpoint

Hotpoint RSAV21T Manual de usuario

Hotpoint

Hotpoint HTH17CBDLWW Instrucciones de montaje

Hotpoint

Hotpoint ENERGY STAR HTJ17CBB Manual

Hotpoint

Hotpoint FFB6200AP Manual de usuario

Hotpoint

Hotpoint RLB20 Manual de usuario

Hotpoint

Hotpoint HTN16BBXWW Manual de usuario

Manuales populares de Refrigerador de otras marcas

Bonnet Neve

Bonnet Neve SKYVIEW PLUS Manual de usuario

Zanussi Electrolux

Zanussi Electrolux ZERB 8441 Manual de usuario

Sharp

Sharp SJ-BA31IEXW2-EU Manual de usuario

CORBERO

CORBERO CC2300MCW Manual de usuario

KitchenAid

KitchenAid 2205264 Manual de usuario

Stengel

Stengel KU 1101 A++ Manual de usuario

NEFF

NEFF KI181 Series Manual de usuario

Hoshizaki

Hoshizaki Reach-In Manual de usuario

Amana

Amana ASD2524VES00 Manual de usuario

BOMANN

BOMANN KGC 213 Manual de usuario

Danby

Danby DAR044A1SLDD Instrucciones de montaje

Samsung

Samsung RF323TE Manual de usuario

Beko

Beko CSA31022 Manual de usuario

IKEA

IKEA FROSTIG C 185 E Manual de usuario

Electrolux

Electrolux ER 6821 D Manual de usuario

True

True TS-28 Manual de usuario

Frigidaire

Frigidaire FSC23R5DW9 Manual de usuario

Beko

Beko LSP4579W Manual de usuario