Hotpoint HTDX100GM Manual de usuario
HTDX100GM – Hotpoint®6.0 cu. ft. capacity DuraDrum™gas dryer
Dryer Dimensions (in inches)
36
24
42-3/4
51
Side View
24
Rear View
36 42
27
25-1/2
2-1/2
25-1/2*
Side View Rear View
4-3/4
25-3/4
23-1/2
11-3/4
HTPWasher/Dryess LC QSart
*24-1/2” from the edge of the side panel to the front.
25-1/2” from front to edge of end caps.
Specification Created 7/10
470158
Exhaust Options:
3-way via rear, left and bottom. Dryer is shipped exhausted to the rear. Alternate exhausting
knockouts are supplied.
Circuit Requirements:
An individual properly-grounded branch circuit, with a three-prong grounding-type receptacle,
protected by a 15- or 20-amp circuit breaker or a time-delay fuse is required.
Gas Dryer Electric Rating:
120V, 60Hz, 6 Amp
Gas (BTU/HR): 22,000. Factory-equipped for natural gas. Tested for LP gas. LP gas supply
requires an optional conversion kit. Check installation instructions for correct kit and have a
qualified gas technician install a conversion kit. See dryer ducting information for proper
installation.
Installation Information: For complete information, see installation
instructions packed with product for current dimensional data.
Special Installation Requirements
Alcove or Closet Installation:
• If your dryer is approved for installation in an alcove or closet, it will be stated on a
label on the dryer back.
• The dryer MUST be exhausted to the outside.
• Minimum clearances between dryer cabinet and adjacent walls or other surfaces are:
0" either side
3" front and rear
• Minimum vertical space from floor to overhead cabinets, ceilings, etc. is 52".
• Closet doors must be louvered or otherwise ventilated and must contain a minimum of
60 sq. in. of open area equally distributed. If this closet contains both a washer and a
dryer, doors must contain a minimum of 120 sq. in. of open area equally distributed.
• No other fuel-burning appliance shall be installed in the same closet with a gas dryer.
Bathroom or Bedroom Installation:
• The dryer MUST be exhausted to the outdoors.
• The installation must conform with the local codes, or in the absence of local codes,
with the National Electric Code and National Fuel Gas Code, ANSI Z223 for gas dryers.
Minimum Clearances other than Alcove or Closet Installation:
• Minimum clearances to combustible surfaces
0" both sides
3" rear
HTDX100GM – Hotpoint®6.0 cu. ft. capacity DuraDrum™gas dryer
Dryer Exhausting Information – Use Metal Duct Only
Vertical and Horizontal Ducting
0 90 ft. 60 ft.
1 60 ft. 45 ft.
6.0 and 5.8 cu. ft. 2 45 ft. 35 ft.
Capacity Models 3 35 ft. 25 ft.
all Electric Dryers 4 25 ft. 15 ft.
0 90 ft. 60 ft.
6.0 and 5.8 cu. ft. 1 60 ft. 45 ft.
Capacity Models 2 45 ft. 35 ft.
all Gas Dryers 3 30 ft. 25 ft.
Portable/StationaryModels
DSKS433EB 0 46 ft. 37 ft.
DSKS333EC 1 38 ft. 30 ft.
DSKP333EC 2 31 ft. 22 ft.
WSM2780H 3 24 ft. 15 ft.
0 56 ft. 42 ft.
1 46 ft. 36 ft.
Unitized Model 2 34 ft. 28 ft.
WSM2700H 3 32 ft. 18 ft.
Unitized Models 0 43 ft. 36 ft.
WSM2420D 1 33 ft. 26 ft.
WSM2480D 2 23 ft. 16 ft.
Number
of
90°
Turns
Maximum Length of
4"-Dia.Rigid MetalDuct
Exhaust Hood Type
Domestic
Dryer Models
A
4" Opening
B
2-1/2"
Opening
Best Performance
B
2-1/2
4
A
A
For complete information, see installation instructions packed with your dryer.
Ducting Materials:
For best performance, this dryer should be vented with 4" diameter all rigid metal exhaust duct.
If rigid metal duct cannot be used, then UL-listed flexible metal (semi-rigid) ducting can be used
(Kit WX08X10077). In special installations, it may be necessary to connect the dryer to the
house vent using a flexible metal (foil-type) duct. A UL-listed flexible metal (foil-type) duct may
be used ONLY in installations where rigid metal or flexible metal (semi-rigid) ducting cannot be
used AND where a 4” diameter can be maintained throughout the entire length of the transition
duct. Please see installation instruction packed with your dryer for complete instructions when
using flexible metal (foil type) ducting.
Exhaust Length Calculation:
1. Determine the number of 90° turns needed for your installation. If you exhaust to the side or
bottom of dryer, add one turn.
2. The maximum length of 4' rigid (aluminum or galvanized) duct which can be tolerated is
shown in the table.
A turn of 45° or less may be ignored. Two 45° turns within the duct length should be treated
as a 90° elbow. A turn over 45° should be treated as a 90° elbow.
Dryers must be exhausted to the outside.
Caution: For personal safety do not terminate exhaust into a chimney, under any enclosed
house floor (crawl space), or into an attic, since the accumulated lint could create a fire hazard or
moisture could cause damage. Never terminate the exhaust into a common duct or plenum with
a kitchen exhaust, since the combination of lint and grease could create a fire hazard.
Exhaust ducts should be terminated in a dampered wall cap to prevent back drafts, bird nesting,
etc. The wall cap must also be located at least 12" above the ground or any other obstruction
with the opening pointed down.
Specification Created 7/10
470158
HTDX100GM – Hotpoint®6.0 cu. ft. capacity DuraDrum™gas dryer
Features and Benefits
• Auto Dry - Monitors air temperature with an automatic thermostat and ends the cycle
when clothes are properly dried
• Rotary electromechanical controls - Easy-to-use controls make it simple to set cycles
• 3 heat selections - Provide the right temperatures for your clothes-drying needs
• Reverse-a-Door - Door opening can be reversed to meet laundry room needs
• Upfront lint filter - With placement of the lint filter in the front of the dryer, air flow
is optimized through the drum, and access to the filter simplifies cleaning
• Cottons cycle - Heat and time are pre-set to take great care of cotton fabrics
• Up to 90 ft. venting capability - Has long equivalent ducting performance for more
flexible installation
• Model HTDX100GWW – White on white
NVLR223E-G
Start
Push to Start
Cottons
Automatic
Medium Heat
80 Min
Optimum Dry
OFF
OFF
70
60
50
40
30
20
Time Dry
Specification Created 7/10
470158
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Secadora de Hotpoint
Hotpoint
Hotpoint AQUALTIS AQC9 BF5 Manual de usuario
Hotpoint
Hotpoint TCD975 Manual de usuario
Hotpoint
Hotpoint TVFS 73B Manual de usuario
Hotpoint
Hotpoint FTCL 87 Manual de usuario
Hotpoint
Hotpoint TVAL 73 Manual de usuario
Hotpoint
Hotpoint TCFS 73B Manual de usuario
Hotpoint
Hotpoint Aquarius VTD20 Manual de usuario
Hotpoint
Hotpoint TVFG 65C Futura Manual de usuario
Hotpoint
Hotpoint DLB2900M Instrucciones de instalación
Hotpoint
Hotpoint FETC 70C Manual de usuario
Hotpoint
Hotpoint DSH 725 H Manual de usuario
Hotpoint
Hotpoint Dm2650R Instrucciones de instalación
Hotpoint
Hotpoint DuraDrum HTDX100EM Instrucciones de uso
Hotpoint
Hotpoint TVFS 83C Manual de usuario
Hotpoint
Hotpoint NJSR453EWWW Manual de servicio
Hotpoint
Hotpoint FTVF XT 75B Manual de usuario
Hotpoint
Hotpoint FTCL 87 Manual de usuario
Hotpoint
Hotpoint NWSR483GBWW Instrucciones de uso
Hotpoint
Hotpoint TFA34 Manual de instrucciones
Hotpoint
Hotpoint TVFS 83 Manual de usuario
Manuales populares de Secadora de otras marcas
Indesit
Indesit IDV 75 Manual de usuario
Infiniton
Infiniton SD-DG85C Manual de usuario
BOMANN
BOMANN WT 5019 Manual de usuario
Alliance Laundry Systems
Alliance Laundry Systems TMB795C Manual de usuario
Asko
Asko T793C Manual de usuario
Kenmore
Kenmore 8041 - 5.8 cu. Ft. Capacity Electric Dryer Manual de usuario