Hoshizaki KM-40B Manual de usuario
(1/13)
Models : KM-40B, KM-55B, KM-80B
- Don't pull the gasket extremely while attach
- If the length of gasket is long, please cut it properly to adjust
No. Figure Note
1
*Open the Door and Remove the shipping
tapes for taking off the Water Tank
2
*Remove the Drain Pipe
3
*Take off the Water Tank by snapping off and
lifting off
4
*To take off the Water Tank, it should be slid
towards you and lifted down
5
*Disconnect the Hose to the Pump Motor
outlet
*Cut the cable tie to disconnect the Hose
*Don't cut the Hose
HOW TO REPLACE THE GASKETS
Rework Time : Approx. 35min
(2/13)
Models : KM-40B, KM-55B, KM-80B
- Don't pull the gasket extremely while attach
- If the length of gasket is long, please cut it properly to adjust
No. Figure Note
HOW TO REPLACE THE GASKETS
Rework Time : Approx. 35min
6
*Disconnect the Hose to the Pump Motor
outlet
7
*Take off the Bin Control Sw to slide it
towards you
*Bin Control Sw is snapped in on both sides
8
*Put the Bin Control Sw in the Bin
temporarily
9
*Close the Door
*Loosen the 2 screws to take off the Top
Panel
10
*Remove the 5 screws to take off the Rear
Top Panel
(3/13)
Models : KM-40B, KM-55B, KM-80B
- Don't pull the gasket extremely while attach
- If the length of gasket is long, please cut it properly to adjust
No. Figure Note
HOW TO REPLACE THE GASKETS
Rework Time : Approx. 35min
11
*Remove the 1 screw securing the Pipe Cover
12
*Remove the Pipe Cover
*Top side is secured by snapping in
*The tab of left bottom side is behind the
front sheet metal
13
*Take off the Grommet to the Pipe Cover for
Water Supply Tube
14
*Disconnect the connector of Pump Motor
15
*Cut the cable tie bundling the wires
(4/13)
Models : KM-40B, KM-55B, KM-80B
- Don't pull the gasket extremely while attach
- If the length of gasket is long, please cut it properly to adjust
No. Figure Note
HOW TO REPLACE THE GASKETS
Rework Time : Approx. 35min
16
*Cut the cable tie bundling the wires
17
*Disconnect the connector of Bin Control Sw
18
*Remove the 1 screw securing the Pump
Motor
*To access the screw, move the refrigeration
pipe above it towards you
19
*After removing the screw, slide the Pump
Motor in the right side, then lift it up towards
you to take off
20
*Remove the 2 screws securing the Water
Valve
*To access the bottom screw, the elbow of
the Water Supply Pipe should be slightly
rotated towards you
*Too much rotation would cause water leak
(5/13)
Models : KM-40B, KM-55B, KM-80B
- Don't pull the gasket extremely while attach
- If the length of gasket is long, please cut it properly to adjust
No. Figure Note
HOW TO REPLACE THE GASKETS
Rework Time : Approx. 35min
21
*Remove the 2 screws securing the Back Side
L shaped Wall
22
*Remove the 2 screws securing the
Evaporator Brackets
23
*Snap off the Back Side L shaped Wall on the
top of both sides
24
*Move the whole Back Side L shaped Wall
towards you
25
*Remove the lead wire of Bin Control Sw
from the rubber Grommet
(6/13)
Models : KM-40B, KM-55B, KM-80B
- Don't pull the gasket extremely while attach
- If the length of gasket is long, please cut it properly to adjust
No. Figure Note
HOW TO REPLACE THE GASKETS
Rework Time : Approx. 35min
26
*Remove the Spray Tube
27
*Move the Water Supply Tube
28
*Slide off the Evaporator Brackets from the
Back Side L shaped Wall
29
*Lift up the whole Evaporator Assembly to
reach the Back Side L shaped Wall
30
*Holding the whole Evaporator Assembly,
then slide up and take off the Back Side L
shaped Wall completely
(7/13)
Models : KM-40B, KM-55B, KM-80B
- Don't pull the gasket extremely while attach
- If the length of gasket is long, please cut it properly to adjust
No. Figure Note
HOW TO REPLACE THE GASKETS
Rework Time : Approx. 35min
31
GASKETS on the Back Side L shaped Wall
2 pieces
32
GASKETS on the Bin
1 piece
33
*Put the whole Evaporator Assembly into the
Bin temporarily
34
*Remove the Gaskets from the Back Side L
shaped Wall and attach the new Gaskets on
the Back Side L shaped Wall in their original
correct position firmly
*Before removing the gaskets, better to apply
and measure the new gaskets length for
p
ro
p
er installation
35
*Remove the aluminum tape around the top
of the Pipe Cover
(8/13)
Models : KM-40B, KM-55B, KM-80B
- Don't pull the gasket extremely while attach
- If the length of gasket is long, please cut it properly to adjust
No. Figure Note
HOW TO REPLACE THE GASKETS
Rework Time : Approx. 35min
36
*Remove the Gasket on the Bin and attach
the new Gasket on the Bin in its original
correct position firmly
37
*Holding the whole Evaporator Assembly,
then slide in and install the Back Side L
shaped Wall in its correct original position
38
*Move and Place the whole Evaporator
Assembly at the front of the Back Side L
shaped Wall
39
*Place the top tabs of the both side of the
Back Side L shaped Wall to the Bin
40
*Secure the 2 screws to install the Back Side
L shaped Wall
(9/13)
Models : KM-40B, KM-55B, KM-80B
- Don't pull the gasket extremely while attach
- If the length of gasket is long, please cut it properly to adjust
No. Figure Note
HOW TO REPLACE THE GASKETS
Rework Time : Approx. 35min
41
*Install the Pump Motor with the 1 screw in
its original correct position in the reverse
order of the removal procedure
42
*Put the rubber Grommet under the Pipe
43
*Install and slide in the Evaporator Brackets
to the Back Side L shaped Wall in its original
correct position in the reverse order of the
removal procedure
44
*Secure the 2 screws to secure the
Evaporator Brackets
45
*Relocate the rubber Grommet for Pipe and
lead wire on both side
(10/13)
Models : KM-40B, KM-55B, KM-80B
- Don't pull the gasket extremely while attach
- If the length of gasket is long, please cut it properly to adjust
No. Figure Note
HOW TO REPLACE THE GASKETS
Rework Time : Approx. 35min
46
*Relocate the Water Supply Tube in its
original correct position
47
*Reroute the lead wires of Float Sw & Bin
Control Sw
48
*Connect the connectors of Bin Control Sw &
Pump motor
49
*Install the Water Valve in its original correct
position in the reverse order of the removal
procedure
50
*Bundle the lead wires of Bin Control Sw &
Pump Motor
Otros manuales para KM-40B
3
Este manual sirve para los siguientes modelos
2
Otros manuales de Máquina de hielo de Hoshizaki
Hoshizaki
Hoshizaki DCM-300BAH Manual de usuario
Hoshizaki
Hoshizaki KMD-460MWJ Manual de usuario
Hoshizaki
Hoshizaki DCM-450BAB Manual de usuario
Hoshizaki
Hoshizaki FM-120EE Guía
Hoshizaki
Hoshizaki DCM-240BAF Manual de usuario
Hoshizaki
Hoshizaki FM-480AKE-HCN Manual de usuario
Hoshizaki
Hoshizaki KM-800MAB Manual de usuario
Hoshizaki
Hoshizaki KM-320MAH Manual de usuario
Hoshizaki
Hoshizaki DCM-500BAF Manual de usuario
Hoshizaki
Hoshizaki FM-120KE Manual de usuario
Hoshizaki
Hoshizaki FM-150KE-50 Manual de usuario
Hoshizaki
Hoshizaki F-650M Manual de usuario
Hoshizaki
Hoshizaki F-300BAF Manual de usuario
Hoshizaki
Hoshizaki KM-80BAJ Manual de usuario
Hoshizaki
Hoshizaki IM-240AWNE-23 Manual de usuario
Hoshizaki
Hoshizaki F-1500MAH Manual de usuario
Hoshizaki
Hoshizaki FM-481AGE-HC Manual de usuario
Hoshizaki
Hoshizaki KM-601DU Manual de usuario
Hoshizaki
Hoshizaki DCM-230HE-UK Manual de usuario
Hoshizaki
Hoshizaki F-251B Manual de usuario
