Hoshizaki KM-2400SRH3 Manual de usuario

™

INSTRUCTION MANUAL

ISSUED: NOV. 14, 2000

KM-2400SRH3

STACKABLE CRESCENT CUBER

Reliability is a

beautiful thing

REVISED: DEC. 11, 2003

Only qualified service technicians should attempt to install, service or maintain this

icemaker. No installation, service or maintenance should be undertaken until the

technician has thoroughly read this Instruction Manual. Likewise, the owner/manager

should not proceed to operate the icemaker until the installer has instructed them on

its proper operation.

HOSHIZAKI AMERICA, INC.

618Highway74South

PeachtreeCity,GA 30269

Attn: HOSHIZAKITechnicalSupportDepartment

Phone: 1-800-233-1940TechnicalService

(770)487-2331

Fax: (770)487-3360

NOTE:NOTE:

NOTE: Toexpedite assistance, all correspondence/communication MUST include the

followinginformation:

• Model Number

• Serial Number

• Complete and detailed explanation of the problem

HOSHIZAKI provides this manual primarily to assist qualified service technicians in the

installation, maintenance and service of the icemaker.

Should the reader have any questions or concerns which have not been satisfactorily

addressed, please call or write to the HOSHIZAKI Technical Support Department for

assistance.

IMPORTANTIMPORTANT

IMPORTANT

CONTENTSCONTENTS

CONTENTS PAGE

I. SPECIFICATIONS ..................................................................................................4

1. NAMEPLATE RATING .........................................................................................4

2. DIMENSIONS/CONNECTIONS ...........................................................................5

II. INSTALLATION AND OPERATING INSTRUCTIONS...........................................6

1. CHECKS BEFORE INSTALLATION....................................................................6

2. HOW TO REMOVE PANELS ...............................................................................6

3. LOCATION ...........................................................................................................7

4. SET UP ................................................................................................................7

5. INSTALLATION OF THE SECOND UNIT..........................................................10

6. ELECTRICAL CONNECTION............................................................................12

7. INSTALLATION OF REMOTE CONDENSER UNIT ..........................................13

[a] CHECKS BEFORE INSTALLATION.............................................................13

[b] LOCATION ....................................................................................................13

[c] SET UP..........................................................................................................14

[d] ELECTRICAL CONNECTION.......................................................................16

8. WATER SUPPLY AND DRAIN CONNECTIONS ..............................................17

9. FINAL CHECK LIST ...........................................................................................19

10. START UP .........................................................................................................20

11. PREPARING THE ICEMAKER FOR LONG STORAGE....................................22

III. MAINTENANCE AND CLEANING INSTRUCTIONS..........................................23

1. CLEANING INSTRUCTIONS .............................................................................23

[a] CLEANING PROCEDURE.............................................................................24

[b] SANITIZING PROCEDURE...........................................................................25

2. MAINTENANCE INSTRUCTIONS .....................................................................26

• Please review this manual. It should be read carefully before the icemaker is installed

and operated. Only qualified service technicians should install, service and maintain

the icemaker. This manual should be made available to the technician prior to

installation, maintenance or service.

• Keep this manual with the icemaker for later reference.

See the Nameplate for electrical and refrigeration specifi-

cations. ThisNameplateislocatedontheupperrighthand

side of rear panel.

Since this Nameplate is located on the rear panel of the

icemaker,itcannotbereadwhenthebackoftheicemaker

is against a wall or against another piece of kitchen

equipment. Therefore,thenecessaryelectricalandrefrig-

erationinformationisalsoontheratinglabel,whichcanbe

easily seen by removing only the front panel of the ice-

maker.

We reserve the right to make changes in specifications and design without prior notice.

I.SPECIFICATIONSI.SPECIFICATIONS

I.SPECIFICATIONS

1. NAMEPLATE RATING1. NAMEPLATE RATING

1. NAMEPLATE RATING

NOT INTENDED FOR OUTDOOR USENOT INTENDED FOR OUTDOOR USE

NOT INTENDED FOR OUTDOOR USE

MAX. CIRC. BREAKER (CANADA ONLY)MAX. CIRC. BREAKER (CANADA ONLY)

MAX. CIRC. BREAKER (CANADA ONLY)

404A

30AMPS30AMPS

30AMPS

30AMPS30AMPS

30AMPS

KM-2400SRH3KM-2400SRH3

KM-2400SRH3

MAX. HACR BREAKER (USA ONLY) 30AMPSMAX. HACR BREAKER (USA ONLY) 30AMPS

MAX. HACR BREAKER (USA ONLY) 30AMPS

30AMPS30AMPS

30AMPS

HI-467PSI LO-230PSIHI-467PSI LO-230PSI

HI-467PSI LO-230PSI

115V115V

115V 0.3A0.3A

0.3A0.3A

0.3A

REMOTEREMOTE

REMOTE 208-230V208-230V

208-230V208-230V

208-230V 5A MAX5A MAX

5A MAX5A MAX

5A MAX

120V 1.2FLA 60W120V 1.2FLA 60W

120V 1.2FLA 60W

208-230/60/3208-230/60/3

208-230/60/3

200-230V 15.0RLA 125LRA200-230V 15.0RLA 125LRA

200-230V 15.0RLA 125LRA

2.DIMENSIONS/CONNECTIONS2.DIMENSIONS/CONNECTIONS

2.DIMENSIONS/CONNECTIONS

Note: When used with a storage bin not recommended by Hoshizaki, the icemaker needs

the space at the bottom opening as in the illustration.

II. INSTALLATION AND OPERATING INSTRUCTIONSII. INSTALLATION AND OPERATING INSTRUCTIONS

II. INSTALLATION AND OPERATING INSTRUCTIONS

1. CHECKS BEFORE INSTALLATION1. CHECKS BEFORE INSTALLATION

1. CHECKS BEFORE INSTALLATION

IMPORTANTIMPORTANT

IMPORTANT

1. Remove shipping carton, tape(s) and packing. If packing material is left in the

icemaker,it will notwork properly.

2. Ensure all components, fasteners and thumbscrews are securely in place.

1) Remove the panels to prevent damage when installing the icemaker. (See “2. HOW TO

REMOVE PANELS.”)

2) Remove the package containing the accessories from the compressor compartment.

3)Remove the protective plasticfilm from the panels. Ifthe icemaker has beenexposedto the

sun or to heat, remove the film after the icemaker cools.

4) Check that the refrigerant lines do not rub or touch lines or other surfaces.

5) Check that the Compressor is snug on all mounting pads.

6) See the Nameplate on the Rear Panel, and check that your voltage supplied corresponds

with the voltage specified on the Nameplate.

7) This icemaker needs a storage bin. The recommended storage bin is HOSHIZAKI ICE

STORAGE BIN, Model B-800 series.

8) On remote air-cooled models, a remote condenser unit is needed. The recommended

remote condenser unit is HOSHIZAKI CONDENSER UNIT, Model URC-24F.

2. HOW TO REMOVE PANELS - See Fig. 12. HOW TO REMOVE PANELS - See Fig. 1

2. HOW TO REMOVE PANELS - See Fig. 1

a) Front Panel.......... Remove the two screws.

Lift up and pull toward you.

b) Top Panel............ Remove the two screws,

and then lift off.

c) Side Panel (R)..... Remove the screw.

Pull slightly toward you,

and take off.

d) Insulation Panel .. Remove the Thumbscrew.

Lift up slightly, and pull toward

you. Fig. 1Fig. 1

Fig. 1Fig. 1

Fig. 1

3. LOCATION3. LOCATION

3. LOCATION

CAUTIONCAUTION

CAUTION

This icemaker is not intended for outdoor use. Normal operating ambient

temperature should be within +45°F to +100°F; Normal operating water

temperature should be within +45°F to +90°F. Operation of the icemaker, for

extended periods, outside of these normal temperature ranges may affect

production capacity.

For best operating results:

•Icemaker should not belocated next to ovens,grills or other highheat producing equipment.

• Location should provide a firm and level foundation for the equipment.

• Allow 6" clearance at rear, sides and top for proper air circulation and ease of maintenance

and/or service should they be required.

4. SET UP4. SET UP

4. SET UP

1)Unpackthe Storage Bin, and attachthefouradjustablelegsprovided(bin accessory) to the

bottom of the Storage Bin.

2) Position the Storage Bin in the selected permanent position.

3) Stack the icemaker on top of the Storage Bin.

4) Secure the icemaker to the Storage Bin by using the two Universal Braces and two of the

bolts provided. See Fig. 2.

Fig. 2Fig. 2

Fig. 2

IMPORTANTIMPORTANT

IMPORTANT

Before operating the icemaker, the Bin Control Thermostat must be installed

correctly.

5) Install the Bin Control Thermostat as follows. See Figures 3a, b and c.

(a)RemovetheTiesecuringtheBulbHolder. RemovetheThermostatBracket(A)fromthe

Shipping Hook by lifting up the Bracket (A) and shifting it to the right.

(b) Lower the Thermostat Bracket through the hole located at the bottom of the icemaker.

Thermostat Bracket (B).

(d) Hook the Thermostat Bracket (A).

(e) Insert the Plug into the Receptacle on the Bracket until it locks in place.

Fig. 3aFig. 3a

Fig. 3a

(f) Secure the Thermostat Bracket in place with the thumbscrew.

(g) Remove the Bin Control Bracket Extension from the accessory bag.

(h) Remove the Baffle from the Bin.

(i) Remove the two screws holding the Bulb Holder (C) to the Thermostat Bracket (B).

If a Hoshizaki Bin is being used:If a Hoshizaki Bin is being used:

If a Hoshizaki Bin is being used:

(j)

Remove the two screws holding the Bulb Holder (C) and the Thermostat Bulb

Attachmenttogether. PutasidetheBulbHolder(C);itisnotneededwiththeHoshizaki

Bin.

(k) Use two of the screws to attach the Bin Control Bracket Extension to the Thermostat

Bracket (B).

(l) Usethetwo4x10stainlesssteelscrewsintheaccessorybagtoattachtheThermostat

Bulb Attachment to the Bin Control Bracket Extension. See Fig. 3b.

(m) Reinstall the Baffle in the Bin.

If a non-Hoshizaki Bin is being used:If a non-Hoshizaki Bin is being used:

If a non-Hoshizaki Bin is being used:

(j) Use the two screws from (i) to attach the Bin Control Bracket Extension to the

Thermostat Bracket (B).

(k) Usethetwo4x10stainlesssteelscrewsintheaccessorybagtoattachtheBulbHolder

See Fig. 3c.

(l)

Reinstall the Baffle in the Bin.

Fig. 3cFig. 3c

Fig. 3c

Fig. 3bFig. 3b

Fig. 3b

4) Remove the panels of the second icemaker.

5) Stack the upper unit on the top of the lower unit.

6)SecuretheupperunittothelowerunitbyusingthetwoUniversalBracesandthefourbolts

provided.

7) Remove the Thermostat Bulb Attachment of the upper unit from the Thermostat Bracket.

8)RoutetheBinControlThermostatCapillaryTubingoftheupperunitthroughthebottomhole

oftheupperunitandtheThermostatBracketofthelowerunit. SecuretheThermostatBulb

of the upper unit to the Thermostat Bulb Attachment of the lower unit with the Thermostat

Bulb Attachment and the screws of the upper unit.

6) Level the icemaker/Storage Bin in both the left-to-right and front-to-rear directions. Adjust

the Ice Bin Legs to make the icemaker level.

7) Place the panels in position.

5. INSTALLATION OF THE SECOND UNIT - See Figures 4 and 55. INSTALLATION OF THE SECOND UNIT - See Figures 4 and 5

5. INSTALLATION OF THE SECOND UNIT - See Figures 4 and 5

1) See “4. SET UP” for the lower unit installation.

2) Remove the Top Panel and the Top Insulation of the lower unit. The Top Panel and the

Top Insulation of the lower unit are not required when installing the second icemaker.

3) Unpack the second icemaker (upper unit), and remove all shipping cartons, tape(s) and

packing.

Fig. 4Fig. 4

Fig. 4

Tabla de contenidos

Otros manuales de Máquina de hielo de Hoshizaki

Hoshizaki

Hoshizaki KML-351MWH Manual de usuario

Hoshizaki

Hoshizaki F-1001MAH Manual de usuario

Hoshizaki

Hoshizaki F-250BAE Manual de usuario

Hoshizaki

Hoshizaki DT-400BAH-OS Manual de usuario

Hoshizaki

Hoshizaki KML-325MWJ Manual de usuario

Hoshizaki

Hoshizaki IM-200BAC Manual de usuario

Hoshizaki

Hoshizaki KM-630MAH Manual de usuario

Hoshizaki

Hoshizaki HS-5245 Manual de usuario

Hoshizaki

Hoshizaki FM-150KE Manual de usuario

Hoshizaki

Hoshizaki KM-1200MAB Manual de usuario

Hoshizaki

Hoshizaki KM-1600SRH Manual de usuario

Hoshizaki

Hoshizaki F-800MAH Manual de usuario

Hoshizaki

Hoshizaki FD-650MAH-C Manual de usuario

Hoshizaki

Hoshizaki DCM-270BAH-OS Manual de usuario

Hoshizaki

Hoshizaki KM-1601SAH Manual de usuario

Hoshizaki

Hoshizaki KM-1600MRB Manual de usuario

Hoshizaki

Hoshizaki DCM-701U Manual de usuario

Hoshizaki

Hoshizaki C-100BAE-AD Manual de usuario

Hoshizaki

Hoshizaki KM-901MAH Manual de usuario

Hoshizaki

Hoshizaki KM-1300SAH-E Manual de usuario

Hoshizaki

Hoshizaki IM-30M Manual de usuario

Hoshizaki

Hoshizaki DCM-300BAH Manual de usuario

Hoshizaki

Hoshizaki IM-45NE Manual de usuario

Hoshizaki

Hoshizaki F-650M Manual de usuario

Manuales populares de Máquina de hielo de otras marcas

Sub-Zero

Sub-Zero 315I Instrucciones de uso

Unold

Unold 48945 Manual de usuario

Kenmore

Kenmore 2217402A Manual de usuario

Cornelius

Cornelius WM600 Instrucciones de funcionamiento

GE XPIO43SCSS Manual de usuario

Whynter

Whynter FIM-450HA Manual de usuario

U-Line

U-Line UMCR014-SC01A Manual de instalación

Andrew James

Andrew James AJ000522 Manual de usuario

Scotsman

Scotsman CME1356 Manual de usuario

Scotsman

Scotsman ACM 25 Manual de usuario

Kärcher

Kärcher IP 120 Manual de usuario

U-Line

U-Line SS1095 Manual de usuario

Maytag

Maytag MIM1554WRS - Ice Maker Manual de usuario

Princess

Princess Yonanas Manual de usuario

Unold

Unold 48946 Manual de usuario

Electrolux

Electrolux E15IM60GP Manual de usuario

Cornelius

Cornelius UC150 ICE ONLY Manual de usuario

Bunn

Bunn BUNN-O-MATIC ULTRA-1 Manual del propietario