Honeywell KI 209 Manual de usuario

INSTALLATION MANUAL

KI 208, KI 209

NAVIGATION INDICATORS

MANUAL NUMBER 006-00140-0004

Revision 4, August 2002

RELEASED FOR THE EXCLUSIVE USE BY: AIRCRAFT ELECTRONICS ASSOCIATION

UP536434

WARNING

PRIOR TO EXPORT OF THIS DOCUMENT, REVIEW FOR EXPORT LICENSE

REQUIREMENT IS NEEDED.

REPRODUCTION OF THIS PUBLICATION OR ANY PORTION THEREOF BY ANY

MEANS WITHOUT THE EXPRESS WRITTEN PERMISSION OF HONEYWELL IS

PROHIBITED. FOR FURTHER INFORMATION CONTACT THE MANAGER, TECHNICAL

PUBLICATIONS, HONEYWELL, ONE TECHNOLOGY CENTER, 23500 WEST 105TH

STREET OLATHE KS 66061 TELEPHONE: (913) 782-0400.

RELEASED FOR THE EXCLUSIVE USE BY: AIRCRAFT ELECTRONICS ASSOCIATION

UP536434

BENDIX/KING KI 208, KI 209

Rev 4, Aug 2002 IM 006-00140-0004 RH-1

REVISION HISTORY

INSTALLATION MANUAL

BENDIX/KING

KI 208, KI 209

Navigation Indicators

PART NUMBER REV DATE DESCRIPTION

---------------------------------------------------------------------------------------------------------------------

006-00140-0004 4 Aug/2002 Replaces P/N 006-00140-0003.

006-00140-0003 3 Oct/1996 Replaces P/N 006-00140-0002.

006-00140-0002 2 Mar/1988 Replaces P/N 006-00140-0001.

RELEASED FOR THE EXCLUSIVE USE BY: AIRCRAFT ELECTRONICS ASSOCIATION

UP536434

BENDIX/KING KI 208, KI 209

Rev 4, Aug 2002 IM 006-00140-0004 RH-2

THIS PAGE RESERVED

RELEASED FOR THE EXCLUSIVE USE BY: AIRCRAFT ELECTRONICS ASSOCIATION

UP536434

BENDIX/KING TABLE OF CONTENTS KI 208, KI 209

Rev 4, Aug 2002 IM 006-00140-0004 TOC-1

SECTION I

GENERAL INFORMATION

Paragraph Page

1.1 Introduction.............................................................................................1-1

1.2 Equipment Description.............................................................................1-1

1.3 Technical Characteristics.........................................................................1-1

1.4 Units and Accessories Supplied ..............................................................1-2

1.5 Accessories Required, But Not Supplied.................................................1-3

1.6 License Requirements.............................................................................1-3

1.7 Requirements for TSO’d VOR/ ILS/ GlideslopeSystem..........................1-3

LIST OF TABLES

Table Page

1-1Technical Characteristics KI 208, KI 209.................................................1-1

SECTION II

INSTALLATION

Paragraph Page

2.1 General....................................................................................................2-1

2.2 UnpackingandInspectingEquipment .....................................................2-1

2.3 Installation KI 208, KI 209.......................................................................2-1

2.4 Post Installation Checkout .......................................................................2-2

LIST OF TABLES

Table Page

2-1ILSDeflection..........................................................................................2-3

2-2GlideslopeDeflection...............................................................................2-3

LIST OF ILLUSTRATIONS

Figure Page

2-1KI 208 Pinout List.....................................................................................2-5

2-2KI 209 Pinout List.....................................................................................2-6

2-3Crimping Tool ..........................................................................................2-7

2-4KI 208, KI 209Connector Assembly .......................................................2-8

2-5KI 208, KI 209Outline and Mounting .....(Dwg 155-05235-0000)...........2-9

2-6KI 208, KI 209TypicalInterconnect ....... ..............................................2-11

2-7KI 208 Non-TSO’d SystemInterconnect.(Dwg 155-01223-0000).........2-13

2-8KI 209 System Interconnect....................(Dwg 155-01241-0000).........2-15

RELEASED FOR THE EXCLUSIVE USE BY: AIRCRAFT ELECTRONICS ASSOCIATION

UP536434

BENDIX/KING TABLE OF CONTENTS KI 208, KI 209

Rev 4, Aug 2002 IM 006-00140-0004 TOC-2

SECTION III

OPERATION

Paragraph Page

3.1 Equipment Operation ..............................................................................3-1

3.2 Indicator Control Functions KI 208, KI 209..............................................3-2

LIST OF ILLUSTRATIONS

Figure Page

3-1KI 208 ControlFunctions.........................................................................3-3

3-2KI 209 ControlFunctions.........................................................................3-4

RELEASED FOR THE EXCLUSIVE USE BY: AIRCRAFT ELECTRONICS ASSOCIATION

UP536434

BENDIX/KING KI 208, KI 209

Rev 4, Aug 2002 IM 006-00140-0004 Page 1-1

SECTION I

GENERAL INFORMATION

1.1 INTRODUCTION

This manual contains information relative to the physical, mechanical and electrical

characteristics of the Bendix/King Silver Crown KI 208 and KI 209.

1.2 EQUIPMENT DESCRIPTION

The Bendix/King KI 208 VOR Indicator is designed to operate with VHF navigational

equipment (such as the KX 155, KX 155A, KX 165A) to provide OMNI (VOR) or LO-

CALIZER (LOC) information. The VHF navigational receiver receives and detects the

omni or localizer information. The KI 208 converts this information to DC signals which

drive the LEFT-RIGHT needle and the TO-OFF-FROM flag of the visual indicator.

The KI 209 ILS Indicator performs the same functions as the KI 208. In addition, it

contains an UP-DOWN glideslope needle with an OFF warning flag.

An anti reflective lens coating is also available on some models of the KI 208 and

KI 209.

1.3 TECHNICAL CHARACTERISTICS

TABLE 1-1 Technical Characteristics KI 208, KI 209

SPECIFICATION CHARACTERISTIC

KI208, KI209 TSO COMPLIANCE: C40a, C36c Class C Cat 2.

DO-138 Environmental Cat. DAPAAAXXXXXX.

ADDITIONAL TSO COMPLIANCE

FOR KI 209 ONLY:

C34c Class D Cat 2.

SIZE: See Figure 2-5 (P/N 155-05235-0000).

WEIGHT:See Figure 2-5(P/N 155-05235-0000).

POWER REQUIREMENTS:

KI 208, KI 209 Indicator

KI 208 Lighting

KI 209 Lighting

KI 208, KI 209 Lighting

14 Vdc at 50 mA, 28 Vdc at 50 mA.

14 Vdc at 80 ±20 mA.

14 Vdc at 160 ±45 mA.

28 Vdc at 80 ±20 mA.

RELEASED FOR THE EXCLUSIVE USE BY: AIRCRAFT ELECTRONICS ASSOCIATION

UP536434

BENDIX/KING KI 208, KI 209

Rev 4, Aug 2002 IM 006-00140-0004 Page 1-2

1.4 UNITS AND ACCESSORIES SUPPLIED

1.4.1 KI 208 VOR Indicator

066-3056-00

066-3056-02 Antireflective lens

1.4.2 KI 209 ILS Indicator

066-3056-01

066-3056-03 Antireflective lens

1.4.3 Bendix/King Equipment Installation Kit (P/N 050-01550-0000) which includes

mating connectors, mounting hardware, etc., is as follows:

VOR/LOC:

Input Impedance:

Nominal Composite Input Level:

Localizer Sensitivity:

OMNI Accuracy:

OMNI Sensitivity:

External Load:

50 k ohms, nominal.

LOC: 0.33 ±10% Vrms.

VOR: 0.50 ±10% Vrms ARINC phased.

4 dB tone ratio will give 3 dot scale deflection.

±2° max error, ±1° typical.

±10° off course gives full scale deflection.

ARINC autopilot deviation (two 1 k loads).

GLIDESLOPE DEVIATION

METER:

Input Impedance:

Deflection Sensitivity:

1 k ±5% ohms.

150 ±5% uA for full scale deflection.

GLIDESLOPE FLAG:

Input Impedance:

Deflection Sensitivity:

1 k ±5% ohms minimum.

125 uA for flag to leave stop.

260 uA maximum for fully concealed flag.

TABLE 1-1 Technical Characteristics KI 208, KI 209

SPECIFICATION CHARACTERISTIC

RELEASED FOR THE EXCLUSIVE USE BY: AIRCRAFT ELECTRONICS ASSOCIATION

UP536434

BENDIX/KING KI 208, KI 209

Rev 4, Aug 2002 IM 006-00140-0004 Page 1-3

PART NUMBER DESCRIPTION QTY VENDOR PART NUMBER

030-02227-0005 Shell, Connector Plug 1 Burndy SMS12P-1

030-02227-0009 Hood, Conn (2 pieces) 1 Burndy SMS12H1

030-02227-0023 Pin, Female Crimp 12 Burndy SC20M-6TK6

088-00706-0000 Tool, Adjustment 1

1.5 ACCESSORIES REQUIRED, BUT NOT SUPPLIED

1.5.1 Antenna.

1.5.2 Interconnecting Cables.

1.5.3 Receiver.

1.5.4 Mooring Plate P/N 073-00044-0001.

1.5.5 Adapter Plate P/N 073-00045-0000 (Front mounting only).

1.5.6Punch Refer to Figure2-5(P/N 155-05235-0000) orother

appropriate drawing.

1.5.7Filing TemplateRefer to Figure2-5(P/N 155-05235-0000) orother

appropriate drawing.

1.5.8 Crimp Tool Burndy Hytool M8ND

1.5.9 Extraction Tool Handle P/N 005-02012-0012, Burndy RXT20-4P3

1.5.10 Extraction Tool Tip P/N 005-02012-0013, Burndy RXK20-25

1.6 LICENSE REQUIREMENTS

None.

1.7 REQUIREMENTS FOR TSO’D VOR/ILS/GLIDESLOPE SYSTEM

Units used in conjunction with the KI 208, KI 209 must meet the specifications listed

below to comprise a completely TSO’d navigation system.

1.7.1 Navigation Receiver Requirements For Use with KI 208, KI 209.

1.7.1.1 The navigation receiver shall be authorized to the standards of TSO C40a,

C40b, C40c, and/or TSO C36c, C36d, C36e.

1.7.1.2 VOR phase error shall not exceed 1.5°.

1.7.1.3 Variation in VOR composite output to not exceed ±3 dB from 0.500 Vrms as

the RF input level of a Standard VOR Test Signal to the receiver is varied from

10 uV to 10,000 uV.

RELEASED FOR THE EXCLUSIVE USE BY: AIRCRAFT ELECTRONICS ASSOCIATION

UP536434

BENDIX/KING KI 208, KI 209

Rev 4, Aug 2002 IM 006-00140-0004 Page 1-4

1.7.1.4 Variation in the LOC composite output shall not exceed ±2 dB from 0.333

Vrms as the RF input level of a Standard Localizer Centering Signal is varied

from 50 uV to 10,000 uV.

1.7.1.5 A control line (ILS Energize) must be provided as a low impedance to ground

when an ILS frequency is selected.

1.7.2 Glideslope Receiver/Converter Requirements For Use with KI 209.

1.7.2.1 The glideslope receiver/converter shall be authorized to the standards of TSO

C34c, C34d, C34e.

1.7.2.2 Centering current to be 0 ±7 uA into a 1000 ohm load with a 95% probability

under all combinations of the service conditions listed in RTCA Paper DO-132,

Minimum Performance Standards - Airborne ILS Glideslope Receiving Equip-

ment paragraph 2.1 sub-paragraph b, Centering Accuracy.

1.7.2.3 Deviation current with a 700 uV Standard Glideslope Deviation Signal (0.091

±0.001 ddm tone ratio) applied to the receiver input shall be 78 ±10% uA into

a 1000 ohm load. Deviation current shall not change more than 15% as the

RF input level of a Standard Glideslope Deviation Signal is varied from 100 to

10,000 uV. Deviation current shall be proportional within 5% to the difference

in depth of modulation of the 90 Hz and 150 Hz tones.

1.7.2.4 Warning signal output shall be a DC current less than 125 uA into a 1000 ohm

load for a warning flag to be fully visible. Warning signal for a fully concealed

warning flag shall be a DC current of 260 uA minimum into a 1000 ohm load.

1.7.3 Fully TSO’D Systems

The following navigation systems will meet all TSO system requirements when

used in conjunction with the KI 208, KI 209:

KX 155

KX 155A

KX 165A

RELEASED FOR THE EXCLUSIVE USE BY: AIRCRAFT ELECTRONICS ASSOCIATION

UP536434

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Panel táctil de Honeywell

Honeywell

Honeywell Tuxedo Touch Series Instrucciones de montaje

Honeywell

Honeywell SmartLine RMA801 Manual de instrucciones

Honeywell

Honeywell Gent Vigilon A3 Mimic Manual de instrucciones

Honeywell

Honeywell VPX Series Manual de usuario

Honeywell

Honeywell CENTRA LINE WEB-HMI Series Manual de usuario

Honeywell

Honeywell XS712 Manual de usuario

Honeywell

Honeywell SmartLine RMA801 Manual de instrucciones

Honeywell

Honeywell UDC 2300 Manual de usuario

Honeywell

Honeywell ADEMCO 6271CV Manual de usuario

Honeywell

Honeywell OmniAssure Manual de usuario

Honeywell

Honeywell 012577 Manual de instrucciones

Honeywell

Honeywell Galaxy TouchCenter Plus Manual de usuario

Honeywell

Honeywell S7999B Manual de operación

Honeywell

Honeywell QXe Recorder Manual de usuario

Manuales populares de Panel táctil de otras marcas

FlowLine

FlowLine Data loop Manual de usuario

ALPEX

ALPEX AEx-8 P Series Manual de usuario

Ltech

Ltech E5S Manual de usuario

Harman

Harman AMX MODERO S MSD-701-L2 Manual de usuario

Acnodes

Acnodes PC 1150 Manual de usuario

AIS

AIS IP10IA99 series Manual de usuario

IBASE Technology

IBASE Technology ASTUT-152-RE1S Manual de usuario

YASKAWA

YASKAWA TP 610C Manual de usuario

B&R

B&R Power Panel C Series Manual de usuario

Beijer Electronics

Beijer Electronics X2 control Manual de usuario

AXIOMTEK

AXIOMTEK GOT321W-521 Manual de usuario

TRIDONIC.ATCO

TRIDONIC.ATCO x-touchBOX Manual de usuario

Qomo

Qomo QIT1386 Manual de usuario

DFI

DFI KS104-CD Manual de usuario

AMX

AMX AXP-PPC Guía

Sartorius

Sartorius X3 PR 5410 Manual de usuario

AMX

AMX Modero X Series Manual de usuario

Advantech

Advantech TPC-30 Series Manual de usuario