Honeywell Posi3 USB Manual de usuario

Page 1 of 11 P/N 13-395 11/4/20 Rev.05

OSI

3 USB Quick Start

Guide

Quick Start Guide Overview

This Quick Start Guide is designed to help you install

your Posi3 USB with basic options that apply to most

users for first time use using a Windows 32/64bit PC

(Windows XP to Windows 7 operating system). For

advanced installations please refer to either the included

Setup Guide or the help file by pressing F1 at any time

during installation.

Table of Contents

• Posi3 USB Components

• Software Installation

• Database Set Up

• Hardware Set Up

• User Set Up

• Adding SBCA Models

• Testing

Posi3 USB Components

Unpack the Posi3 USB and accessories and verify that

all parts are present. Do not discard the shipping

cartons and packing materials – they are necessary for

returning the Posi3 USB to Honeywell Analytics for its

annual calibration.

• Posi3 USB

• Head Assembly

• Tygon ฀ tube

• Low Pressure Manifold*

• High Pressure Manifold*

• First Stage Manifold*

• Head Gasket

 4 Standoffs

 4 Tightening Knobs

 CD-ROM

 Setup Guide

 Quick Start Guide

 USB Cable

 Power Cable

 3 High Pressure Manifold Replacement O-Rings*

 3 Low Pressure Manifold Replacement O-Rings*

 High Pressure Manifold Replacement Hex-Head

Screw*

 Spare Fuse (2)

*Not included with European model.

Basic Software Installation

All POSI3 USB software end users must have

permission to modify the following areas of the PC:

The registry section

HKEY_LOCAL_MACHINE\SOFTWARE\Sperian\Pos

USB and all its subsections.

The folder location C:\Program

Files\Sperian\Posi3USB and all its subfolders.

It may be necessary to contact your IT department so

they can provide you with the necessary access.

Note on Brand-Specific Software: If you are planning to service a

specific brand of SCBA, make sure you have the OEM Posi3 USB

software for that brand.

To install your POSI3 USB software, if having a

CD, insert the CD-ROM. If the software fails to

launch automatically, use Windows Explorer to

navigate to the CD-ROM drive and run

BATestSetup.exe. If having a downloaded file, be

sure to have the BATestSetup.exe and the

License.exe applications in the same folder.

It is recommended to exit any other Windows

programs that may be running and verify the

License information and End User License

Agreement.

Page 2 of 11 P/N 13-395 11/4/20 Rev.05

OSI

3 USB Quick Start

Guide

By default, the software is installed to

C:\Program Files

(x86)\Sperian\Posi3USB\Standard\BATest.

Follow the screen prompts to continue installation

with default settings.

Database Setup

The Database Installation Wizard is automatically

launched near the end of the software installation.

First time installation requires the installation

of the PostgreSQL Server.

(For advanced installation or connecting to an

existing server, please refer to the included Setup

Guide or Help File by pressing F1 at any time)

Note: Administrator-level system access is

required to install the PostgreSQL database

server.

In some versions of Windows, you may need to click

“OK” to proceed.

Choose the Basic Installation and click "Install"

The PostgreSQL installation will begin

automatically.

A separate application is used to install the server. F1

help is not available in the database installation

application.

Do not continue with the Database Installation

Wizard until the database server installation is

complete.

When you are back at the Database Installation

Wizard, click “Next” to install the model’s

database.

The Database Installation Wizard will

automatically choose the location, port to use, as

well the Server Owner Name and Password

(biosystems).

Select “Install a NEW test results database” and

click “Next”.

Page 3 of 11 P/N 13-395 11/4/20 Rev.05

OSI

3 USB Quick Start

Guide

Type in a name for the test results database (Special

characters and spaces are not allowed). Click OK.

Click the Finish button to exit the Database

Installation Wizard.

For Windows 7 or above, restarting the PC is

optional.

Advanced Software Installation

All POSI3 USB software end users must have

permission to modify the following areas of the PC:

The registry section

HKEY_LOCAL_MACHINE\SOFTWARE\Sperian\Pos

USB and all its subsections.

The folder location C:\Program

Files\Sperian\Posi3USB and all its subfolders.

It may be necessary to contact your IT department so

they can provide you with the necessary access.

Note on Brand-Specific Software: If you are planning to service a

specific brand of SCBA, make sure you have the OEM Posi3 USB

software for that brand.

To install your POSI3 USB software, if having a

CD, insert the CD-ROM. If the software fails to

launch automatically, use Windows Explorer to

navigate to the CD-ROM drive and run

BATestSetup.exe. If having a downloaded file, be

sure to have the BATestSetup.exe and the

License.exe applications in the same folder.

It is recommended to exit any other Windows

programs that may be running and verify the

License information and End User License

Agreement.

By default, the software is installed to

C:\Program Files

(x86)\Sperian\Posi3USB\Standard\BATest.

Follow the screen prompts to continue installation

with default settings.

Database Setup

The Database Installation Wizard is automatically

launched near the end of the software installation.

First time installation requires the installation

of the PostgreSQL Server.

(For advanced installation or connecting to an

existing server, please refer to the included Setup

Guide or Help File by pressing F1 at any time)

Note: Administrator-level system access is

required to install the PostgreSQL database

server.

In some versions of Windows, you may need to

click “OK” to proceed.

Page 4 of 11 P/N 13-395 11/4/20 Rev.05

OSI

3 USB Quick Start

Guide

Choose the Advanced Installation and click "Install"

The PostgreSQL installation will begin

automatically.

A separate application is used to install the server. F1

help is not available in the database installation

application.

Do not continue with the Database Installation

Wizard until the database server installation is

complete.

PostgreSQL Welcome screen will be shown;

click Next.

Select the Install directory. By default,

C:\Program Files\PostgreSQL\10. Click Next.

Select all components to be installed

Select the Data directory. By default,

C:\Program Files\PostgreSQL\10\data. Click

Next.

Note: If for any reason the Data is needed in a

different path, contact Honeywell Tech Support

for assistance.

Page 5 of 11 P/N 13-395 11/4/20 Rev.05

OSI

3 USB Quick Start

Guide

Assign a User and Password for the

PostgreSQL Server. By recommendation use

a. User: postgres

b. Password: postgres

Click Next.

By default, the Port to be used will be

configured to 5432. Click Next.

Note: If you need to change and it is blocked by

your company; contact your local IT to ensure

the port to be assigned is usable.

10.

For Advanced Options, select the [Default

locale] configuration. Click Next.

11.

Review the Installation Summary and if all

configurations are correct click Next. Correct if

necessary.

Page 6 of 11 P/N 13-395 11/4/20 Rev.05

OSI

3 USB Quick Start

Guide

12.

Installation will require a confirmation then will

proceed without interference

13.

When the installation is done, uncheck Launch

Stack Builder at exit. Click Finish.

14.

When you are back at the Database Installation

Wizard, click Next to configure the PostgreSQL

Server into the POSI Software.

15.

Follow the below default configuration. Click

Logon.

16.

When you are back at the Database Installation

Wizard, click Next to install the model’s

database.

17.

The Database Installation Wizard will use the

configured location, port to use, as well the Server

Owner Name and Password. Click Next.

18.

Select Install a NEW test results database and

click “Next”.

Page 7 of 11 P/N 13-395 11/4/20 Rev.05

OSI

3 USB Quick Start

Guide

19.

Type in a name for the test results database (Special

characters and spaces are not allowed). Click OK.

20.

Click the Finish button to exit the Database

Installation Wizard.

21.

For Windows 7 or above, restarting the PC is

optional.

Hardware Setup

Installing the Test Head

(No tools are necessary for installation)

1. Screw the four standoffs into place at the top of the

chassis until they are hand tight.

2. Place the head gasket into position on the bellows

chamber inlet.

3. Connect the Tygon™ tube from the hose barb on the

bottom of the head to the hose barb at the bottom

front of the inside of the bellows.

4. 4. Slide the head onto the standoffs. Make sure the

Tygon™ tube is not caught or pinched between the

head and the chassis.

5. 5. Hand tighten the four knobs on top of the

threaded standoffs. No tools are necessary. Do not

over tighten!

Install the Microphone (optional)

Plug the microphone into the port located on the Posi3

USB’s left front panel over the medium pressure inlet.

Connect the PC to the Posi3 USB

The software must be installed before connecting the

USB cable and turning on the Posi3 USB.

Connect the unit using the supplied power and USB

cables.

Turn on the Unit

Note: Honeywell Analytics recommends the Posi3 USB

be plugged into a surge protector.

Do not mount an SCBA facepiece on the test head prior

to turning the Posi3 USB on.

Install the USB Drivers

A "Found New Hardware" wizard is shown the first time

you connect the Posi3 USB to the PC and turn it on.

Page 8 of 11 P/N 13-395 11/4/20 Rev.05

OSI

3 USB Quick Start

Guide

Follow the directions and wait until it is complete.

Automatic installation is recommended. If you are given

the option to connect to Windows Update to search for

software, select No.

Launch the Software

The Posi3 USB should be connected to the PC and

turned on prior to launching the software the first time.

Double-click the desktop icon or click the Start button / All

Programs / Sperian / Biosystems Posi3 USB / Standard

Edition / SCBA Test

Overview of Initial Software Set Up

1. Log in to the software

2. Set up a new user account

3. Create an apparatus model (Standard version only)

4. Create a serial number

Initial Login

1. The initial User ID and password are both “Setup”

2. Log on then click “Done”.

3. Click “Open” to open the test results database

4. Click “Done” on the Notifications screen

5. Click the "Initialize PosiChek" checkbox. The Posi3

USB must be connected by the USB cable to

establish communication.

User Set Up

The Setup User has the ability to create new users, but

does not have the ability perform tests or add/modify

models.

1. Click the menu item Setup / Users / User List.

2. Click the + button to add a new user.

Page 9 of 11 P/N 13-395 11/4/20 Rev.05

OSI

3 USB Quick Start

Guide

3. Enter the user’s information (as needed). The

User ID field and the Password field must be

completed.

4. Set the Permissions level to 4.

5. Click the Check button to save the information.

6. Click the Log on button at the lower left, and log on

with the User ID and password of the user you just

created.

Adding SCBA Models

Note: This step is only necessary in Standard Version

Posi3 USB software. Brand-specific versions of software

come with pre-installed models and do not allow end

users to configure models.

1. Click the menu item Setup / Apparatus / Add New

Model.

2. Click “New” to enter the Model Configuration window

3. Enter the Manufacturer and Model

4. Select the supply pressure of the cylinder (2216 PSI,

3000 PSI or 4500 PSI)

5. Select the type of apparatus (SCBA, Airline

Apparatus, SCBA/Airline or Facepiece)

6. Click “Next” to start selecting the components of the

model

7. You will be prompted to select a first stage. Double-

click or drag and drop a component from the left pane

so that it appears in the right pane.

Page 10 of 11

P/N 13-395 11/4/20 Rev.05

OSI

3 USB Quick Start

Guide

Note: "MP" stands for Medium Pressure. For models

with a Medium Pressure connection in the Standard

Software, the medium pressure readings will be

shown on appropriate tests. The Standard Software

does not contain tolerances for the medium pressure

tests, so there will be no indication whether the

medium pressure portion of the tests passes or fails.

8. Click “Next” to continue to the next component of the

breathing apparatus. You will be prompted to select a

second stage, facepiece, alarm(s), and gauge(s).

9. When selected, the components of the model will be

shown in the right pane of the Choose Model screen.

Adding Serial Numbers

Note - Serial Numbers can be imported from your

PosiChek3 software by using the File / Import menu item.

See Setup Guide for more information.

1. Click the menu item Setup / Apparatus / Add New

Serial Number

2. Select the model for the serial number and click “OK”

3. Enter the serial number and other specific information

about the apparatus.

4. Click “Accept” to save.

Testing

Attaching the Facepiece

Position the facepiece squarely on the test head, and

tighten the straps evenly. Make sure the nose cup is

positioned over and across the test head nose.

Do Not connect the second stage regulator to the

facepiece until the software instructs you to do so. The

facepiece must be open to ambient air pressure when the

facepiece leak test is started.

Attaching the High or Low Pressure Manifold

1. Turn off the cylinder valve on the SCBA to be tested

and depressurize it by using the bypass.

2. Disconnect the SCBA from the cylinder. If the

cylinder will not be used as the pressure source for

testing, it can be removed during testing.

Otros manuales para Posi3 USB

Tabla de contenidos

Otros manuales de Equipo de prueba de Honeywell

Honeywell

Honeywell POL-200-TS Manual de usuario

Honeywell

Honeywell S300RPTU Manual de usuario

Honeywell

Honeywell Posi3 USB Manual de usuario

Honeywell

Honeywell IQ Force Dock Manual de usuario

Honeywell

Honeywell TKA295 Manual de usuario

Honeywell

Honeywell MicroDock II Manual de usuario

Honeywell

Honeywell Posi 3 Manual de usuario

Honeywell

Honeywell TESTAIR 4 Manual de usuario

Honeywell

Honeywell TB7200 Series Manual de usuario

Honeywell

Honeywell Vibrex 2000 Manual de usuario

Honeywell

Honeywell BW MicroDock II Manual de usuario

Honeywell

Honeywell Enraf VITO 762 Manual de usuario

Honeywell

Honeywell FG701 Manual de usuario

Honeywell

Honeywell HPBLT Manual técnico

Manuales populares de Equipo de prueba de otras marcas

SMART

SMART KANAAD SBT XTREME 3G Series Manual de usuario

Agilent Technologies

Agilent Technologies BERT Serial Manual de usuario

Agilent Technologies

Agilent Technologies N3280A Manual de usuario

Vernier

Vernier Go Direct Voltage Manual de usuario

Lifeloc

Lifeloc R.A.D.A.R. Manual de usuario

Fluke

Fluke T5-600 Instrucciones de funcionamiento e instalación

Mercury

Mercury TSL01 Manual de usuario

MAHA

MAHA MBT Series Manual de usuario

Fuji Electric

Fuji Electric P-61 Manual de usuario

ETC

ETC SealerAtor Manual de usuario

Skyfine

Skyfine ETHYWAY V2 Manual de usuario

Appion

Appion G5 Twin Manual de usuario

PCB Piezotronics

PCB Piezotronics 8159-0112A Manual de usuario

BW Technologies

BW Technologies MicroDock II Manual de usuario

Sun Nuclear

Sun Nuclear 1027 Manual de usuario

Biomark

Biomark HPR LITE READER Manual de usuario

Hioki

Hioki 3169-20 Manual de usuario

Ashcroft

Ashcroft ATE-100 Manual de usuario