Honeywell Miller Revolution Harness Manual de usuario

90014448 ind F 27/07/2015I239 MFP9720160

Index

English........................................................................................................3

Français ..................................................................................................10

Deutsh.....................................................................................................17

Nederlands..........................................................................................24

Suomi.......................................................................................................31

Svenska ..................................................................................................38

Italiano....................................................................................................45

Česky ........................................................................................................52

Русский..................................................................................................59

INSTRUCTIONS FOR USE

Thank you for purchasing the Miller Revolution Harness. The Revolution is an all new and totally innovative

harness engineered with eight unique components and more than eleven key product features. Your Miller Revo-

lution harness was engineered to meet or exceed all applicable CE requirements and standards. Please carefully

read the new Miller Harness Instruction manual to help you identify all of the various general warnings, inspection

procedures and other helpful information.

Please carefully read this supplementary Revolution Instruction manual. It contains special instructions, inspec-

tions and maintenance procedures that are unique to the Revolution Harness product line. Should you have any

questions about your Miller Revolution Harness, please contact the Miller Customer Service at: +44 (0)1256 693200

Preparing your harness for use:

• Before you don (wear) the harness, you must read and understand the Miller Harness

Instruction manual.

• Although your harness is « ready-to-use », sizing it the rst time will require some adjustments

to ensure a proper, snug t. By taking the time to adjust the harness correctly the rst time, you

will eliminate the need for future readjustments.

A. Miller Revolution Key Features

A.1 A.2

A.3

A.4

A.5

A.1 PivotLink™ Connection

The PivotLink connection allows you a greater freedom of movement while wearing your harness than

was previously available. By pivoting at the hip or at the waist, there’s no pulling or tugging when you bend.

The PivotLink is designed to be « self-cleaning », but if dirt or debris begins to collect inside of the metal, use

compressed air, a soft brush and/or warm water with a mild detergent to clean it. Check for free movement and

make sure the PivotLink does not bind. Do not apply lubricants to the PivotLink mechanism.

A.2 Web Finials

Web Finials on all adjustable webbing ends provide a gripping surface for easier adjustment, in addition to

providing a way to secure and organize the loose webbing with the integrated clip.

A.3 Self-Contained Label Pack

The new self-contained label pack encapsulates labels minimizing damage and loss. It is conveniently located on

the chest for easy access, and it incorporates integrated pull-free lanyard rings for securing lanyards when not in

use.

A.4 ErgoAmor™Back Shield

Semi-Flexible ErgoAmor back shield minimizes impact from sharp/heavy snap hooks and self-retracting lifelines.

1.e The back shield also provides two locations for custom labels.

The left for a company label, and the right for a high visibility individual worker identication label. Both may

be purchased separately. Please contact your sales person or Miller customer service for more information on

company specic ID. Complete with integrated dorsal D-ring.

A.5 Integrated Accessory system

The integrated modular accessory system provides a wide variety of options for attaching belts, tools, and

accessories to your Revolution harness.

A.6 DualTech™ Webbing

Miller’s new DualTech Webbing makes donning easy with two-sided contrasting colours and textures. The

webbing is engineered with a shape-retention memory for a more comfortable t. In addition, the black outside

and grey coloured inside make identifying twisted straps when donning the harness easier. Also available with

DuraFlex webbing.

A.7 Cam Buckle

The Cam buckle allows easy one-hand adjustment and release of shoulder straps. Their non-slip design promotes

proper snug t of the harness, and allows for easy adjustment to accomodate seasonal clothing.

A.6 A.7

DONNING THE REVOLUTION WITHOUT BELT

B. Donning the Revolution without belt

B.1 Hold harness by back D-ring. Shake harness to allow all straps to fall in place.B.2 If leg or chest straps are

buckled, release straps and unbuckle at this time.

B.3 Slip straps over shoulder so D-ring is located in the middle of the back between shoulder blades.

B.4 Pull buckle portion of leg strap between legs and connect to opposite end of leg strap. Repeat with second

leg strap.

B.5 Connect chest strap. The shoulder strap retainer (chest strap) must be positioned in the mid-chest area 15 to 20

cm below the trachea but not below the sternum.Fasten securely to keep shoulder straps taut.

B.6 After all straps have been buckled, thighten webbing so that harness ts snug, but allows full range of

movement. To maximize comfort, be sure to adjust the harness so that the PivotLink centers are at waist level.

B.7 Front anchorage loops should be level with the sternum. When using this anchorage point, the intermediate

attachment should be connected to both loops.

B.8 To remove harness, release quick connect or tongue buckles.

B.1 B.2 B.3

B.4 B.5 B.6

DONNING THE REVOLUTION WITH BELT

C. Donning the Revolution with belt

C. 1 Hold harness by back D-ring. Shake harness to allow all straps to fall in place.

C.2 If leg or chest straps are buckled, release straps and unbuckle at this time.

C.3 Slip straps over shoulder so D-ring is located in the middle of the back between shoulder blades.

C.4 Pull buckle portion of leg strap between legs and connect to opposite end of leg strap. Repeat with second

leg strap.

C.5 Attach integral work-positioning belt. (Connecting belt rst ensures PivotLink is in the proper location.)

C.6 Connect chest strap. The shoulder strap retainer (chest strap) must be positioned in the mid-chest area 15 to

20 cm below the trachea but not below the sternum. Fasten securely to keep shoulder straps taut. After all straps

have been buckled, tighten webbing so that harness ts snug, but allows full range of movement. To maximize

comfort, be sure to adjust the harness so that the PivotLink centers are in the right position:

C.7 Construction Harness With belt:The PivotLink centres are positioned at waist level

C.8 Utilities & Telecom Harness : The PivotLink centres are on the outside of the hips

C.9 To remove harness, reverse procedure.

C.1 C.2 C.3

C.4 C.5 C.6

C.7 C.8

STEPS FOR ENSURING A SNUG FIT

D. Adjusting Cam Buckles

D.1 Unclip the web end nial from the webbing.

D.2 Pull webbing downwards to adjust tighter

D.3 Reposition web end nial.

INSTALLING OPTIONAL ACCESSORIES

E. Connecting Accessories

E.1 Locate the gure « 8 » shaped composite attachement clip on the back of the accessory.

E.2 Identify the green button attachement point on the belt or harness that will be used.

E.3 Place the widest end of the gure « 8 » over the green connection button.

E.4 Push the accessory downward until you feel it snap into place.

E.5 To remove, reverse procedure by gripping 1 loop and pulling upward. Miller integrated accessories have a

weight limit of 11kg, when connected via the composite link. For loads heavier than 11kg, connecting to a belt

via the tunnel loop is recommanded for more even weight distribution. The combined weight of the harness

user, and all attached tools and accessories should not exceed the maximum capacity of the fall protection

system being used.

D.1 D.2 D.3

E.1 E.2 E.3 E.4

INSTALLING SHOULDERS PADS

F. Optional Shoulder Pads

Optional harness shoulder pads are available.

Please contact your sales person or Miller customer service for more information.

G. Installing shoulder pads

G.1 Turn the harness, so that the D-ring is laying up on a at surface.

G.2 Take one of the shoulder pads and place your nger over the Velcro® .

G.3 Lift up the webbing shoulder strap and carefully slide the Velcro portion of the shoulder pad into the pocket.

G.4 Remove your nger and press the two Velcro strips together.

G.5 Finish by wrapping the other two sets of Velcro around the shoulder strap webbing.

G.1 G.2 G.3

G.4 G.5

AVAILABLE ACCESSORIES

H. Available accessories

H.1 Cell Phone Holders (two sizes)

H.2 Water Bottle Holder

H.3 2 Pocket Nail & Tool Pouch

H.4 Open Bolt Bull Pin Bags

I. Materials specic to the Revolution harness

I.1 PivotLink: Aluminium, Polypropylene, Stainless steel

I.2 TechWeb: Polyester, Nylon

I.3 Label Pack: Polypropylene, Santoprene

I.4 Pads (Belt, Shoulder, Back): Polyester, Nylon

I.5 D-Ring Assembly: Stainless steel, Santoprene and Polyethylene Blend, Nylon.

I.6 Cam-Buckle: Aluminium, Stainless steel, Nylon

H.1 H.2 H.3

H.4

I.1 I.2 I.3

I.4 I5 I6

Instructions générales

Nous vous remercions d’avoir acheté le Harnais Révolution Miller. Il s’agit d’un harnais totalement nouveau et

innovant dont la conception comprend huit composants uniques et plus de onze équipements clés. Votre harnais

Révolution Miller a été conçu pour atteindre, voir dépasser les exigences et les standards de toutes les normes eu-

ropéennes. Veuillez lire attentivement le nouveau manuel d’Utilisation du Harnais Miller comprenant les instruc-

tions spéciques, ainsi que les procédures de surveillance et d’entretien qui sont propres à la gamme de produits

du Harnais Révolution. Il vous aidera à identier les diérentes mises en garde, les procédures de surveillance et

autres informations utiles.

Si vous avez des questions concernant votre Harnais Révolution Miller, veuillez vous adresser au Service Clientèle

Miller au : +33 (0)2 48 52 40 42

Préparation préalable à l’utilisation du harnais:

• Avant de porter votre harnais, vous devez lire et comprendre le manuel d’Utilisation du

Harnais Miller.

• Bien que votre harnais soit“prêt-à-l’emploi”, la première utilisation nécessitera quelques

réglages an qu’il soit ajusté à votre taille. En prenant le temps d’ajuster correctement le

harnais la première fois, vous éviterez de futurs réglages.

A. Les équipements clés du harnais Révolution Miller

A.1 A.2

A.3

A.4

A.5

Tabla de contenidos

Idiomas:

Otros manuales de Sensor de seguridad de Honeywell

Honeywell

Honeywell FG8M Manual de usuario

Honeywell

Honeywell V-Plex IS3050A-SN Manual de usuario

Honeywell

Honeywell 5800COMBO Manual de usuario

Honeywell

Honeywell HS3PIR1X Manual de usuario

Honeywell

Honeywell 5800PIR-OD Manual de instrucciones

Honeywell

Honeywell FG-730 Manual de usuario

Honeywell

Honeywell OMV-VX Series Manual de usuario

Honeywell

Honeywell MDA Scientific MIDAS Manual de usuario

Honeywell

Honeywell Miller Stopfall 7700A/YL/GP-1 Manual del operador

Honeywell

Honeywell NOTIFIER IRX-751CTEM Manual de usuario

Honeywell

Honeywell FF-SPS4 Series Manual de usuario

Honeywell

Honeywell RAELink3 2.4GHz Manual de usuario

Honeywell

Honeywell Vitoject 890 Manual de usuario

Honeywell

Honeywell C7061A1020 Manual de usuario

Honeywell

Honeywell Sensepoint XCD RFD Manual de usuario

Honeywell

Honeywell 5800PIR-RES Manual de usuario

Honeywell

Honeywell Connected Home DO8EZS Manual de usuario

Honeywell

Honeywell C7962B Manual de operación

Honeywell

Honeywell Ex-Or MLS2500D Manual de instalación y operación

Honeywell

Honeywell SPM Flex Manual de usuario

Honeywell

Honeywell 5800PIR Manual de usuario

Honeywell

Honeywell Sensepoint XCD RFD Nota de versión

Honeywell

Honeywell Farenhyt Series Manual de usuario

Honeywell

Honeywell FlexGuard 5853 Manual del propietario

Manuales populares de Sensor de seguridad de otras marcas

THORLABS

THORLABS PDA10JT Manual de usuario

Waeco

Waeco UV-DETECT Manual de usuario

Intermatic

Intermatic IOS-DSIMF Manual de usuario

urmet domus

urmet domus 1083 Manual de usuario

Siemens

Siemens AZL66 Series Manual de usuario

BTI

BTI Profiline Multi Finder Manual de usuario

Challenger

Challenger SL01 Manual de usuario

DMP Electronics

DMP Electronics 1122INT Manual de usuario

Rielta

Rielta Ladoga MK-RK Manual de usuario

Mirion Technologies

Mirion Technologies ACCURAD PRD Manual de usuario

Bosch

Bosch DS835 Manual de usuario

DBI SALA

DBI SALA EZ Stop Manual del operador

Lamptime

Lamptime ST05C Manual de usuario

Ubiquiti

Ubiquiti MFI-MSC Manual de usuario

Subsite

Subsite 910R Instrucciones de instalación

Satel

Satel OPAL Pro Manual de usuario

Aleph

Aleph XC-1XTEU Manual de usuario

Pima

Pima LARIS QUAD Manual de usuario