Honeywell GLEN ALDEN Manual de usuario

GLEN ALDEN 52” CEILING FAN

MODEL #50180

Questions, problems, missing parts? Before returning to your retailer, call our customer

service department at 1-877-361-3883, Monday - Thursday, 8 am - 6 pm, EST and Friday,

8 am - 5 pm, EST.

Español p. 15

WELCOME

PREPARATION

Before beginning the assembly of this product, ensure

that all parts are present. Compare all parts with the

package contents list and hardware contents list. If

any part is missing or damaged, do not attempt to

assemble the product.

After opening the top of the carton, remove the

mounting hardware package from the foam inserts,

then remove the motor from the packaging and

place it on a soft surface, such as a carpet, to avoid

damage to the nish.

Estimated Assembly Time: Under 60 minutes

Tools Required for Assembly (not included): Electrical

Tape, Phillips Screwdriver, Pliers, Safety Glasses,

Step Ladder, and Wire Strippers

Helpful Tools (not included): AC Tester Light, Tape

Measure, Wiring Handbook, and Wire Cutters

CARE AND MAINTENANCE

At least twice each year, lower the canopy to check

the downrod assembly, and then tighten all screws

on the fan. Clean the motor housing with only a soft

brush or lint-free cloth to avoid scratching the nish.

Clean the blades with a lint-free cloth. You may

occasionally apply a light coat of furniture polish to

wood blades for added protection.

Important: Shut off the main power supply before you

begin any maintenance tasks. Do not use water or a

damp cloth to clean the ceiling fan.

FAN WEIGHT

The net weight of this fan is: 12.54 lbs. (5,69 kg).

TABLE OF CONTENTS

ATTACH YOUR RECEIPT HERE

Serial Number

Purchase Date

Care and Maintenance ........................2

Package Contents ...........................3

Safety Information ...........................4

Mounting Bracket Installation ...................5

Hanging Your Fan............................6

Wiring .....................................7

Motor Housing Installation .....................8

Blade Installation ............................9

Final Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Operating Installation . . . . . . . . . . . . . . . . . . . . . . . .11

Replacement Parts List ......................12

Troubleshooting ............................13

Limited Lifetime Warranty.....................14

PACKAGE CONTENTS

Unpack your fan and check the contents. You should

have the following items:

1. Upper Mounting Bracket

2. Motor with Lower Mounting Bracket

3. Blade (5)

4. Blade Arm (5)

5. Switch Housing Cap

6. Motor Housing

7. Loose parts bags containing (not shown):

Mounting hardware, electrical hardware, pull

chains, wire connectors, etc.

SAFETY INFORMATION

Please read and understand this entire manual before attempting to assemble, operate, or install the product.

• Before you begin installing the fan, disconnect the power by removing fuses or turning off the

circuit breakers.

• Make sure that all electrical connections comply with local codes, ordinances, the National Electrical

Code, and ANSI/NFPA 70-199. Hire a qualied electrician or consult a do-it-yourself wiring handbook if

you are unfamiliar with installing electrical wiring.

• Make sure the installation site you choose allows a minimum clearance of 7 ft. (2,14 m) from the blades

to the oor and at least 30 in. (76 cm) from the end of the blades to any obstruction.

DANGER

WARNING

When using an existing outlet box, make sure

the outlet box is securely attached to the building

structure and can support the full weight of

the fan. Failure to do this can result in serious

injury or death. The stability of the outlet box is

essential in minimizing wobble and noise in the

fan after installation is complete.

To reduce the risk of re or electric shock, do not

use the fan with any solid-state speed-control

device or control the fan speed with a full-range

dimmer switch.

To reduce the risk of re, electric shock, or personal

injury, mount the fan to an outlet box marked

“ACCEPTABLE FOR FAN SUPPORT” and use the

mounting screws provided with the outlet box. Most

outlet boxes commonly used for the support of

lighting xtures are not acceptable for fan support

and may need to be replaced. Consult a qualied

electrician if in doubt. Secure the outlet box directly

to the building structure. The outlet box and its

support must be able to support the moving weight

of the fan at least 35 lbs. (15,88 kg).

WARNING

CAUTION

To reduce the risk of re, electric shock, or

personal injury, do not bend the blade arms

when installing them, balancing the blades, or

cleaning the fan. Do not insert objects between

the rotating fan blades.

Read all instructions and safety information

before installing your new fan. Review the

accompanying assembly diagrams.

Be sure the outlet box is properly grounded or

that a ground (green or bare) wire is present.

! !

7' Min

30" Min

MOUNTING BRACKET INSTALLATION

1. Turn off the circuit breakers and the wall switch to

the fan supply line lead (Fig. 1).

DANGER: Failure to disconnect the power

supply prior to installation may result in serious

injury or death.

2. Ensure that the blades will be at least 30 in. (76 cm)

from any obstruction and at least 7 ft. (2,13 m) above

the oor (Fig. 2).

Fig. 1

Fig. 2

Fig. 3

Outlet Box

Upper Mounting

Bracket

3. Secure the upper mounting bracket to the outlet

box using screws provided with the outlet box

(not included) and the two at washers from the

hardware bag (Fig. 3).

Note: It is very important that you use the proper

hardware when installing the mounting bracket as

this will support the fan.

Flat Washer

Bracket Screw

Tab

Screw Hole Slot

4. Remove the four bracket screws from underneath

the lower mounting bracket and save for later use

(Fig. 4).

Bracket Screw

Washer

Fig. 4

Fig. 5

HANGING YOUR FAN

Bracket

Screw

6. Reinstall the previously removed bracket screws

underneath the lower mounting bracket and into

the upper mounting bracket. Securely tighten the

screws (Fig. 6).

Fig. 6

5. Place tab on the lower mounting bracket into slot in

the upper mounting bracket. Then slide the second

lower mounting bracket tab into the second slot

on the upper mounting bracket until all four screw

holes are in alignment (Fig. 5).

Black (live)

White (neutral)

Bare/Green (ground)

Black

Blue

White

Green

OFF

Black (live)

Second Wire (live)

White (neutral)

Bare/Green (ground)

Black

Blue

White

Green

OFF OFF

Wire Connector

CAUTION

WARNING

If house wires are different colors than referred to in

the following step, stop immediately. A professional

electrician is recommended to determine wiring.

Incorrect wire connection can damage the receiver

and could cause re or injury.

Be sure outlet box is properly grounded or that a

ground (green or bare) wire is present.

! !

Fig. 7

Fig. 8

7. Connect supply and fan wires according to the

diagram (Fig. 7) and these steps:

• Connect the Green wires from mounting bracket to

the Bare/Green (ground) supply wire.

• Connect the Black and Blue wire from the fan to

the Black (live) supply wire.

• Connect the White wire from the fan to the White

(neutral) supply wire.

Secure all wiring connections together with wire

connectors and push all connected wires back into

the outlet box.

8. (Optional) If a second hot power wire is available

from outlet box, connect it to the blue (light power)

wire from the fan for separate light and fan control

(Fig. 8).

Important: The black fan wire is power for fan. The blue

fan wire is power for the light. The white wire from

the fan is common/neutral. The green wires from the

fan and mounting bracket are ground wires.

WIRING

MOTOR HOUSING INSTALLATION

10. Temporarily lift the motor housing to the mounting

bracket to determine which two motor housing

screws in the sides of the mounting bracket align

with the slotted holes in the top edge of the motor

housing. Partially loosen the two motor housing

mounting screws that align with the slotted holes.

Remove the other two motor housing mounting

screws from opposite sides of the mounting bracket

(Fig. 10).

11. Slide the motor housing over the motor, aligning

the slotted holes in the motor housing with the two

loosened motor housing mounting screws in the

mounting bracket. Twist motor housing to lock. Then

reinstall the two previously-removed motor housing

mounting screws and securely tighten all screws

(Fig. 11).

9. Remove the ten motor screws from the underside of

the motor. Set aside for blade arm assembly (Fig. 9).

Mounting

Bracket

Fig. 10

Fig. 11

Motor Housing

Screw

Motor Housing

Screw

Washer

Motor

Housing

Motor

Housing

Screws

Motor

Housing

Screws

Fig. 9

Motor Screw

BLADE INSTALLATION

Fig. 13

Motor Screw

Blade

Isolator

Blade Arm

Blade

Cutout

Blade

Twist Lock

Connector

Blade Arm

Fig. 12

12. The blades attach to blade arms using the Fast

AttachTM system.

Align each twist lock connector in the direction of

its corresponding hole in the blade. Place the blade

over the twist lock connectors. Rotate each twist

lock connector so that it is perpendicular to the

hole in the blade. Repeat for the remaining blades

(Fig. 12).

Note: A cutout in the upper switch housing allows

easy access to the motor screw holes.

13. Insert the two previously removed motor screws

through one blade arm and blade isolator and then

into the motor. Tighten motor screws securely.

Repeat with remaining blade arms, making sure

to completely secure each blade arm before

proceeding (Fig. 13).

Motor Screw

15. The pull chain extension or custom pull chain

extension (sold separately) may be attached to fan

pull chains (Fig. 15).

Fig. 15

Fan

Pull Chain

Fan Pull Chain

FINAL INSTALLATION

Screw Washer

14. Remove the three screws and washers from the

upper switch housing. Connect plug from the motor

to the plug from the switch housing cap. Align holes

in the switch housing cap with holes in upper switch

housing. Re-install screws and washers that were

previously removed. Use a Phillips screwdriver (not

included) to secure all screws (Fig. 15).

Switch

Housing

Cap

Screw

and

Washer

Fig. 14

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Admirador de Honeywell

Honeywell

Honeywell PERFECT WINDOW ER150 Manual de usuario

Honeywell

Honeywell HS-1650 Series Manual de usuario

Honeywell

Honeywell HT-112E Manual de usuario

Honeywell

Honeywell HT-800 Series Manual de usuario

Honeywell

Honeywell HS-2007 Series Manual de usuario

Honeywell

Honeywell HY-047B - Fresh Breeze Tower Fan Manual de usuario

Honeywell

Honeywell BIRNHAM Manual de usuario

Honeywell

Honeywell Glencrest Manual de usuario

Honeywell

Honeywell QUIETSET HY-254 Series Manual de usuario

Honeywell

Honeywell HW-500C Series Manual de usuario

Honeywell

Honeywell HT-380 Series Manual de usuario

Honeywell

Honeywell L4064A-F Manual de usuario

Honeywell

Honeywell HTF090E Series Manual de usuario

Honeywell

Honeywell QUIETSET HS1655E Manual de usuario

Honeywell

Honeywell HV-140E Manual de usuario

Honeywell

Honeywell TrueFRESH VNT5150H1000 Manual de usuario

Honeywell

Honeywell HV-1800E Manual

Honeywell

Honeywell MEGA TURBO HF-810 Manual de usuario

Honeywell

Honeywell QUIETSET HY-105 Series Manual de usuario

Honeywell

Honeywell HSF1640 Series Manual de usuario

Honeywell

Honeywell HV-140E Manual de usuario

Honeywell

Honeywell HT-906 Series Manual de usuario

Honeywell

Honeywell QUIETSET HY-254 Series Manual de usuario

Honeywell

Honeywell HY254E Manual de usuario

Manuales populares de Admirador de otras marcas

ELTA FANS

ELTA FANS H03VV-F Manual de usuario

Hunter

Hunter 20714 Manual de instrucciones

Emerson

Emerson CARRERA VERANDA CF542ORB00 Manual de usuario

Hunter

Hunter Caraway Manual de instrucciones

Panasonic

Panasonic FV-15NLFS1 Manual de usuario

Kompernass

Kompernass KH 1150 Manual de usuario

VES

VES FALA100/12V/TR Manual de usuario

Vertiv

Vertiv Liebert DCD Manual de usuario

Westinghouse

Westinghouse GFP Series Manual de usuario

Venmar

Venmar KUBIX HRV PLUS Series Manual de usuario

Maico

Maico ECR 31 Manual de usuario

Sonnenkonig

Sonnenkonig Dinky Manual de usuario

S&P

S&P ECOWATT HXBR Manual de usuario

Wider

Wider IMP03369BH Manual de usuario

Panasonic

Panasonic F-60DHN Manual de usuario

Hinkley

Hinkley HIGHLAND Manual de usuario

Broan

Broan 766BN Manual de usuario

Premium

Premium PFS16022 Instrucciones de montaje