Honeywell CS071AE Manual de usuario

TROUBLE-SHOOTING GUIDE

Description of Problem Possible Causes Possible Corrective Action

Blisters • Excessive moisture. • Pre-dry sheet at the temperature

required for the material you are

forming.

• Heat sheet very slowly to forming

temperature.

• Protect sheet from moisture before

using.

• Heating sheet too hot. • Cut down sheet forming

temperature. You may be boiling

the stabilizers out of the material.

• Heating sheet too fast. • Lower element temperatures.

Generally speaking, element

temperatures should not exceed

950°F.

• Increase the distance between the

heating elements and the sheet.

• Uneven heating of the sheet. • Check forming oven for elements

that are overheating.

• Screen out hot spots.

• Heat sensitive material. • Check with plastic supplier on

temperature parameters for the

material involved.

Thinning • Design of the part. • The overall draw ratio of the part is

too great for the starting thickness

of the sheet.

• The part has specific areas on it

that exceed the draw ratios of the

rest of the part.

• Sheet too thin. • Increase the gauge thickness of the

plastic sheet.

• Uneven sheet temperature. • Check for air drafts in the forming

oven.

• Check for hot spots in the forming

oven. May have defective heating

elements.

• Check the sheet for a variation in

thickness.

• Forming technique. • Consider where the part is thinning

and what forming technique would

best address this problem.

• Bad plastic sheet. Melt

index of sheet may be low.

• Have physical properties of the

sheet analyzed.

TROUBLE-SHOOTING GUIDE

Description of Problem Possible Causes Possible Corrective Action

Discoloration • Forming temperature too

hot.

• Cut down on the forming

temperature of the sheet.

• Pigment loading too low. • Increase pigment loading.

• Hot spots in forming oven. • Check out heating elements.

Webbing or bridging • Poor mold design or layout. • Redesign mold.

• Use plug assist or mechanical ring

to eliminate webbing.

• Add spacing blocks to take up

excess material.

• Increase draft or radii to webbed

area.

• Slow down the vacuum speed.

• Redesign ring or plug assist.

• If it is a multiple mold, increase the

spacing between parts.

• Wrong forming technique or

bad design on present

technique.

• Select a better forming technique.

• Make mold adjustments to the

current technique. Gussets, etc.

• Incorrect sheet temperature. • In billow forming, the corners of

the sheet may be too hot.

• In snapback forming, the corners of

the sheet may be too cold.

• Screen out appropriate areas of the

sheet.

• High sheet sag. • Cut down the heat of the sheet to

be formed.

• Select a resin with a lower melt

index.

• Vacuum rate too fast. • Slow down the vacuum rate.

• • Use smaller vacuum holes

• Restrict the vacuum flow with ball

or gate valves in the main vacuum

line.

• Insufficient vacuum. • Check the vacuum system for

leaks.

• Increase the number of vacuum

holes.

• Check to see if the vacuum holes

are plugged up.

• Check to see if the vacuum holes

are in the proper area.

TROUBLE-SHOOTING GUIDE

Description of Problem Possible Causes Possible Corrective Action

• Selectively increase the size of the

vacuum holes.

• Timing the billow in the

snapback box.

• Get a more sensitive flow valve.

• Put an electric eye in the snapback

box.

Sheet pulls out of clamp

frame.

• Clamp frames warped. • Put a piece of paper in the clamp

frame and see if you can pull it out

without tearing it.

• Clamping pressure too low. • Seals leaking on clamp frames.

• Air pressure to clamp frames

adjusted to low.

• High shrinkage in plastic

sheet.

• Put double-sided adhesive foam

tape with 40-grit emery paper on

the clamp frames.

• If possible, control the orientation

in the plastic sheet.

Lumps and bumps. • Contamination in the sheet. • Cut a cross section of the lump and

examine it to see if looks different

than the plastic matrix. If so, it is

an extruder issue.

• Incompatible plastic mixed

within the sheet.

• Check incompatible lump with an

IR test.

• Compare color of lump with the

rest of the matrix.

• Water droplets on hot plastic

sheet.

• Cut a cross section of the lump and

check for compatibility.

• Bump on the mold. • Look for a depression on the side

of the sheet touching the mold.

• Loose debris on the mold. • Look at the back of the formed part

for loose debris imbedded within

the part.

Texture washout. • Draw ratio of the part too

great.

• Consider a deeper texture.

• Plastic sheet heated too hot,

especially on the texture

side.

• Turn down the texture side heaters

in the oven.

• Cut down the heater cycle time.

• Cut down the overall heat on the

sheet.

• Shade out certain areas of the sheet

to keep it cooler and less

susceptible to thinning.

TROUBLE-SHOOTING GUIDE

Description of Problem Possible Causes Possible Corrective Action

Texture separation. • Texture too deep for starting

thickness of the sheet.

• Select a different texture.

• Texture has deep furrow

lines in a pattern.

• Select a different texture.

• The material you are using may

have poor hot strength and you

may need to select a different one.

• Excessive shrinkage in the

extruded sheet.

• Draw ratio pretty large, in

excess of 3 to 1.

• Select a tighter texture.

• Change the processing technique

for forming the part.

Sheet won’t fit into clamp

frame.

• Sheet not flat. • Place a weight on the bowed up

area along the clamp frame.

• Preheat sheet to remove stress.

Flow lines on part. • Nerve in the plastic sheet. • Rerun the sheet.

• Chatter due to sloppy chain

drive on the extruder.

• Run material on a good direct drive

extruder.

• Select a deeper texture.

• Melt index of resin erratic. • Blend resin more thoroughly.

• Die lines on the back of the

sheet.

• Rerun sheet.

• Run sheet from the oven at a lower

temperature.

• Select a deeper texture.

Blotchy look on the texture

side of amorphous materials.

• Excessive heat, especially

on PVC containing

materials.

• Cut down the forming temperature

heat.

• Select a better texture. Some hair

cell textures will do this in PVC

containing materials.

• High oven shrinkage. • Check shrinkage and keep within

acceptable limits.

Blotchy look on the texture

side of olefin materials.

• Poor mold contact. • Sandblast mold surface.

• Uneven cooling on the mold • Get a temperature-controlled mold.

• Check cooling lines for blockages.

TROUBLE-SHOOTING GUIDE

Description of Problem Possible Causes Possible Corrective Action

Inconsistent part. • Uneven heat on plastic

sheet.

• Check for air drafts in the heating

oven.

• Check the sheet for a variation in

gauge.

• Check for power output variations.

• Bad regrind in plastic sheet. • Do an IR or a Brabender test to

confirm compound consistency.

• Part too difficult for the

forming technique being

used.

• Change to a technique that is

suitable.

Warped parts. • Parts are cooling unevenly. • Use temperature controlled tooling.

• Check temperature controlled

tooling for water flow blockages.

• Check the material distribution on

the mold. Is the proper forming

technique being used?

• Check if the plastic sheet is being

pulled tightly against the mold.

Very important in forming the

olefins.

• Check cooling fans for proper

placement.

• Check for plugged vacuum holes.

• Mold too cold. • Preheat the mold.

• Clamp frames too cold. • Preheat the clamp frames. This is

especially important when forming

the olefins.

• Excessive gauge variation

on the finished part.

• Change forming technique to get

better material distribution.

• Insert screens in the oven to shade

out thinning areas.

• Gauge on flat sheet may be all over

the lot. Check various areas of the

sheet for gauge differences.

• Check for hot spots in the oven.

Do the thin spots occur on the

same spot consistently?

• Demolding temperature too

hot.

• Increase cooling cycle.

• Decrease mold temperature.

• Get more cooling fans cooling the

part.

• Overheated sheet. Material • Cut back on oven c

cle time or

TROUBLE-SHOOTING GUIDE

Description of Problem Possible Causes Possible Corrective Action

sagging too much. heat.

• Poor mold design. • Add a moat if you are dealing with

the olefins.

• Check for plugged vacuum holes.

• Add more vacuum holes.

• Use an alternate forming technique.

• Sandblast the mold in the case of

olefins.

• • Check mold for flexing during the

vacuum cycle.

• Poor part design. • Avoid large flat areas. Crown the

part if possible.

• Put in ribs or cosmetic designs in

the flat areas.

• Avoid severe draw ratios.

Poor detail on part. • Sheet too cold. • Increase heating time in oven.

• Increase heating element

temperature.

• Check oven for consistency.

• Check oven for drafts.

• Insufficient vacuum. • Check for leaks in the vacuum

system.

• Check to see if the system delivers

enough vacuum.

• Check to see if the mold is leaking

vacuum and/or sealing properly.

• Check to see if some vacuum holes

are clogged.

• Check to see if you have enough

vacuum holes.

• Check for the proper location of

the vacuum holes and are they the

proper size.

• Cold clamping frame. • Preheat the clamping frame to get a

better seal.

• Incorrect forming technique. • Change forming technique to best

suit the geometry of the part.

• Em

assist to

et better

TROUBLE-SHOOTING GUIDE

Description of Problem Possible Causes Possible Corrective Action

material distribution and vacuum

seal.

• Hot strength of material too

great.

• Select a material with less hot

strength.

• Use pressure-forming technique to

make the part.

• Plastic too thick in area with

poor detail.

• Use a different forming technique

to distribute the material better.

• Heat the area with the thick plastic

hotter.

Poor surface finish on part. • Mold surface too rough. • Polish mold surface to a smoother

finish.

• Sandblast the mold surface.

• Chill marks. • Get temperature controlled tool.

• Run current mold hotter.

• Change forming technique to

eliminate chill marks. Adjust

predraw depth.

• Draft angle too severe. • Add more draft to the part.

• Mold surface creates too

much drag.

• Polish mold in selected areas.

• Apply mold release sparingly in

selective areas.

• Air entrapment between the

mold and formed part.

• Add more vacuum holes to the

affected area.

• Sandblast mold surface.

• Dirty sheet. • Clean sheet with isopropyl alcohol

or deionizing airgun.

• Dirty mold. • Clean mold off with airgun or

mechanical means.

• Dirt and debris in the

atmosphere.

• Put in filtering system.

• Clean up the thermoforming area

thoroughly.

• Isolate the thermoforming area.

• Contaminated sheet. • Wipe sheet off before putting it in

the thermoformer.

• Separate sheet out that has

contaminates imbedded into it.

• Voids. • Cull out affected sheets where

possible.

• Scratched surface on sheet. • Interleaf sheet. Handle sheet

carefully.

TROUBLE-SHOOTING GUIDE

Description of Problem Possible Causes Possible Corrective Action

• Avoid dragging the corner of the

sheet across the surface of the

textured side.

• Streaks. • Examine what you are cleaning the

sheet with before putting it into the

thermoformer.

• Undispersed pigment in the sheet.

• Poor mixing during extrusion.

Rerun the material.

• Dirty embossing roll during the

extrusion process. Clean the

texture roll.

• Dust and dirt in the

atmosphere.

• Keep the thermoforming area

clean. Put in a filter system if

necessary.

Chill marks. • Mold temperature too low.

Material freezes onto the

mold when it touches it.

• Increase the mold temperature.

• The radius on the part is too

small.

• Redesign the part to accommodate

a larger radius.

• Wrong forming technique is

being used.

• Change the forming technique to

an appropriate one.

• Insufficient draft angle on

the part.

• Increase the draft angle.

• Plug temperature too low. • Increase the plug temperature.

• Cover the plug with an insulative

material.

• Use an insulating material to make

the plug.

• Sheet too hot. • Cut down the oven temperature.

• Reduce the heating cycle.

Dimples on mold side of parts. • Vacuum holes too large. • Decrease vacuum-hole size.

• Sheet too hot. • Reduce the heating cycle or cut

down the oven temperature.

• Dirt or debris on the mold

surfaces.

• Clean the mold frequently during

the forming operation.

• Vacuum rate is too high. • Cut down the vacuum volume.

Color loss or stress whitening

or blushing.

• Sheet too cold. • Heat sheet to a higher temperature

before forming.

• Sheet too hot. • Cut back on heating cycle to

prevent discoloration.

TROUBLE-SHOOTING GUIDE

Description of Problem Possible Causes Possible Corrective Action

• Reduce the temperature of the

heaters to prevent surface

scorching.

• Reduce the distance the heaters are

in relation to the sheet being

heated.

• Part too thin. • Increase the thickness of the sheet.

• Change the forming technique to

improve the part thickness.

• Shade the oven or turn down the

element temperatures in the area

the part is thinning.

• Mold too cold. • Increase mold temperature.

• Poor mold design. • Change draft angles.

• Increase radii.

• Change mold geometry to reduce

the draw ratio.

Poor material distribution

and/or excessive thinning in

specific areas.

• Uneven heating of the sheet. • Check the heaters to see if they are

set properly.

• Check for faulty heaters.

• Check for drafts or air currents in

the oven.

• Shade oven if element zoning is

not possible.

• Check to see if the elements are too

close to the plastic.

• Excessive gauge variation in

the sheet.

• Check the gauge of the sheet.

• Cold mold. • Increase the mold temperature.

• Check the mold for plugged water

lines.

• Excessive sag. • Cut down sheet temperature.

• Use zone heating to cut down

temperature in the center of the

sheet.

TROUBLE-SHOOTING GUIDE

Description of Problem Possible Causes Possible Corrective Action

Shiny streaks on part. • Sheet too hot in certain

spots.

• Control the heat in the hot zone of

the sheet by cutting down the

element temperature in the specific

area.

• Increase the distance between the

heater and the sheet.

• Screen the entire oven to dissipate

the heat more evenly.

• Check the unformed plastic sheet

for shiny spots.

Thin corners on the formed

part.

• Sheet too thin. • Use heavier gauged sheet.

• Poor material distribution. • Reduce sheet forming temperature.

• Change forming technique to get

better sheet distribution.

• Change from female to male mold.

• Sheet temperature too high

at the corners.

• Use screening or control the

temperature of the heating zones.

Excessive shrinkage after part

is removed from the mold.

• Inadequate cooling. • Increase cooling cycle time.

• Reduce the mold temperature.

• Employ better cooling fans.

• Place cooling fans in more logistic

places.

• Use cooling fixtures.

Shrink marks on formed part. • Poor seal edge on the mold. • Repair or improve the seal edge.

• Put in a moat on the mold.

• Mold surface too smooth. • Put as sandblast finish on the mold.

• Inadequate vacuum. • Check mold and vacuum system

for leaks.

• Increase vacuum capacity.

• Check for plugged vacuum holes.

• Add vacuum holes or increase the

size as appropriate.

Difficult to remove part off

the mold.

• Insufficient draft on a male

mold.

• Increase draft.

• Remove the part from the mold as

hot as possible without warping it.

• Male mold temperature too

cold.

• Increase the mold temperature to

keep the part from cooling too

much.

• Mold surface too rough for

the draft angle.

• Smooth out the mold in the areas

that are locking on.

Otros manuales para CS071AE

Otros manuales de Acondicionador de aire de Honeywell

Honeywell

Honeywell R-MM14CCS Manual de usuario

Honeywell

Honeywell CL201AE Manual de usuario

Honeywell

Honeywell MN series IM Manual de usuario

Honeywell

Honeywell CO60PM Series Manual de usuario

Honeywell

Honeywell CL25AE Manual de usuario

Honeywell

Honeywell CS12AE Manual de usuario

Honeywell

Honeywell MO Series Manual de usuario

Honeywell

Honeywell CO70PE Manual de usuario

Honeywell

Honeywell MM14CCSBB Manual de usuario

Honeywell

Honeywell HWAC-1217S Manual de usuario

Honeywell

Honeywell CO30XE Manual de usuario

Honeywell

Honeywell CS10XE Series Manual de usuario

Honeywell

Honeywell MN09CES Manual de usuario

Honeywell

Honeywell CO301PC Manual de usuario

Honeywell

Honeywell MF08 Series Manual de usuario

Honeywell

Honeywell CL15AM Manual de usuario

Honeywell

Honeywell HL10 Series Manual de usuario

Honeywell

Honeywell HM2CESSWK8 Manual de usuario

Honeywell

Honeywell MP09 Series Manual de usuario

Honeywell

Honeywell CS071AE Manual de usuario

Honeywell

Honeywell MM14CCS Manual de usuario

Honeywell

Honeywell CL30XC Manual de usuario

Honeywell

Honeywell DCS2AE Manual de usuario

Honeywell

Honeywell CS071AE Manual de usuario

Manuales populares de Acondicionador de aire de otras marcas

Spheros

Spheros CC 355 Manual de usuario

Bosch

Bosch Climate 5000 SCI 24 CAS/ OU- OUE Manual de usuario

Panasonic

Panasonic CS-E12HKEW Manual de usuario

nedis

nedis ACMB1WT7 Manual de usuario

Samsung

Samsung AR KV Series Guía

Daikin

Daikin FCFV50A Manual de usuario

Fujitsu

Fujitsu Inverter ASBA30JFC Manual de usuario

Toshiba

Toshiba RAS-M10SMUV-E Manual de usuario

Daikin

Daikin FXLQ20MAVE Manual de usuario

Hitachi

Hitachi RAS-E24CAK Manual de usuario

CIAT

CIAT Magister 2 Series Guía

Bestron

Bestron AAC6000 Manual de usuario

Hisense

Hisense 7K Manual técnico

Frigidaire

Frigidaire FFRE0533S1E0 Manual de usuario

Samsung

Samsung AS09HM3N Manual de usuario

Frigidaire

Frigidaire CRA073PU11 Manual del propietario

Soleus Air

Soleus Air GB-PAC-08E4 Manual de usuario

McQuay

McQuay MCK020A Manual de usuario