Honeywell DC515 Series Manual de usuario

Installation and Operation Guide

Portable and Plug-In Wireless Doorbell

English

German

French

Dutch

Spanish

Portuguese

Italian

DC515XX

Preparation

Doorbell

Push

Button

Flat Head

Screws

Phillips Screwdriver

Standard Screwdriver

Push Button Mounting

Bracket

and Adhesive Pad

To install you will need

Content will vary according to your kit

The push button supplied with this kit is pre-programmed to operate with the doorbell.

If it is not, see “Connect a Push Button” on page 7. Push button model may vary

from the one shown above.

CR2032 Battery

Mounting Bracket

Wall

Anchors

Round Head

Screws

Change the Light Pattern

Press the Sunlight button to change the lights that ash

when the doorbell rings.

Press the Sunlight button

1 time 2 times 3 times 4 times

Halo light and

top lights

Halo light only Top lights only No lights

Overview

Just follow these simple steps:

1. Install the push button battery. Depending on the model, plug in the

doorbell or install the batteries in it.

2. Set up the doorbell and your preferences.

3. Install the push button.

Doorbell for indoor use only. Do not expose to liquid, vapour or rain.

Power-up

1. Choose an outlet location that is not near a heat

source, where the doorbell will be easy to see and

hear and power it.

2. Open the push button battery cover and install the

CR2032 battery.

Setup and Operation

Press the push button to test whether it is paired with the doorbell. The

doorbell will light up and ring. If it does not, see “Connect a Push Button” on

page 7.

Change the Tune

Press the Music button to change the doorbell tune.

Every time you press the Music button, the tune will

change. Stop pressing the Music button when you hear

the tune you want.

If you have multiple push buttons paired with the chime,

you can select the melody for the last push button that

was triggered.

Press the push button. (For any new push button, ensure

that it is paired rst. Refer to “Connect a Push Button” on

page 7.)

Within 12 seconds, press the melody selection button

until the desired tune is selected.

Ding Dong

Westminster

Piano

Fantasy

Soft Alert

Smart Sax

Change the Halo Light Colour

Press the push button.

Within 12 seconds, press the Sunlight

button.

Light Blue

White

Red

Dark Blue

Green

Purple

Yellow

Every time you press the Sunlight

button, the halo light will change

colour. Stop pressing the Sunlight

button when you see the colour you

want:

Adjust the Volume

Press the Volume

Up or Volume

Down buttons to

adjust the volume

of the Doorbell.

Mute the Doorbell

Press the

Mute button

to silence the

doorbell.

Install Push Button

1. Mount the push button

bracket in the desired

location. Use the screws.

–OR–

Use the adhesive backing. If

using the adhesive backing,

clean the surface first.

2. Snap the push button onto

the mounting bracket.



Note: If you need to remove the push button, use a small

screwdriver to release the tab.

Set the Mute

You can also mute the doorbell for specic amounts of time.

Press the Mute button.

Mute button shows Doorbell is mute

1 time doorbell is mute

2 times 3 hours

3 times 6 hours

Mute button shows Doorbell is mute

4 times 9 hours

5 times 12 hours

6 times no longer mute

It is also easier to unmute the doorbell by pressing and holding the mute

button until it beeps.

Wall Mount Installation (Portable Models Only)

Choose a location that is not near a heat source or on something that moves

(like a door). For non-mounting locations, choose a place where the doorbell

will be easy to see and hear.

Install Doorbell

If you are not mounting the doorbell to the wall, place the doorbell where you

want it.

1. Screw the doorbell wall mounting

bracket to the wall using the

included screws and

anchors (if necessary).

Drill 1/4-inch holes for

the anchors.

2. Hang the doorbell on

the mounting bracket.

For DC515XX

models

Before linking your outdoor motion

sensor, you will need to adjust its

settings:

Turn the Dusk control and Time control

fully anti-clockwise to its minimum

setting.

Ensure your sensor is in Day Mode. This

will be shown by the slider button being

in the left position (Sun symbol).

Connect a Motion Sensor

1. Press and hold the Setting button on

the doorbell for three seconds.

The halo light will circle.

2. Within 20 seconds of pressing the

Setting button, wave or make some

other kind of motion in front of the

motion sensor.

Accessories

You can connect up to 4 accessories to your doorbell, including other push

buttons, window or door opening sensors, and motion sensors.

If you try to connect more accessories than the maximum number, the

doorbell will sound two beeps.

Models nly)

Your doorbell can also be used as a night-light.

1. Plug the doorbell into a wall outlet.

2. Press and hold the Night-light button to select the

halo colour.

3. Release the Night-light button when you see the

colour you want.

Secret Knock

For each push button, you can set up a Secret Knock

that has a different ring and halo light colour. The

Secret Knock is triggered by pressing the push button

quickly 3 times.

1. Press the push button 3 times quickly.

2. Within 12 seconds of pressing the push button, press the Music button to

select the ring for the Secret Knock.

3. Within 12 seconds of pressing the push button, press the Sunlight button

to select a halo light colour for the Secret Knock.

Connect a Push Button

Follow these steps to change the ring and halo light colour for an existing

doorbell, too.

1. Press and hold the Setting button on

the doorbell for three seconds.

The halo light will circle.

2. Press the push button.

3. Within 12 seconds of pressing the

push button, press the Music button

to select the ring for that push

button.

4. Within 12 seconds of pressing the

doorbell, press the Sunlight button

to select a halo light colour for that

push button.

Plug socket shown

above for reference

will vary by country/

region

Maintenance

Your doorbell and push button require no maintenance except to periodically

change the battery.

If using the correct battery, its life should be approximately:

• Up to 2 years for the push button; replace with CR2032 lithium battery

Low Battery Notification

When the push button batteries are low, two beep sounds are heard after the

normal tune.

When the batteries are low on the portable doorbells (battery models), the

bottom edge of the halo light ashes yellow every 6 seconds until the batteries

are replaced.

Reset

This process removes all pairings, including the push button that came with

this doorbell:

1. Unplug the doorbell or remove the batteries from the portable model.

2. Press and hold the Setting button and plug the doorbell back in at the

same time.

3. The halo light will circle and the doorbell is returned to its default factory

settings.

Specications

Doorbell Push Button

Operating Temperature  

Honeywell Home ActivLink™ 868 MHz 868 MHz

  

 84 dB -

Battery Type 

models only 

 Up to 2 years - battery models

only Up to 2 years

Rain proof N/A IP55

Troubleshooting

If Then

The doorbell does not work

 

 Ensure the correct batteries are installed in both the push and doorbell



 The doorbell might be out of range; try the doorbell in a different



 

 

 



 

 

Two ‘beep’ sounds are

heard after the normal tune 

Range is reduced

 



 

 



*Under these scenarios the push button is considered the “transmitter”. Other

examples of transmitters are the wireless motion (PIR) sensor or wireless door

window sensor.

www.resideo.com

license from Honeywell International Inc.

32343180-001 Rev.A

https://livewell.honeywellhome.com

Otros manuales para DC515 Series

Tabla de contenidos

Otros manuales de Accesorios de Honeywell

Honeywell

Honeywell 705 Series Manual de usuario

Honeywell

Honeywell DT7550UK2 DUAL TEC Manual de usuario

Honeywell

Honeywell IntelliSense IS25100TC Manual de usuario

Honeywell

Honeywell Ex-Or BattenFit MSB1000T Manual de instalación y operación

Honeywell

Honeywell RPW318 Manual

Honeywell

Honeywell 5898 Manual de usuario

Honeywell

Honeywell RPW212A Guía del usuario

Honeywell

Honeywell IRPI8EZS Manual de usuario

Honeywell

Honeywell SIXMINICT Manual de servicio

Honeywell

Honeywell DT8012F4 Manual de usuario

Honeywell

Honeywell RPWL4045A2000 Manual de usuario

Honeywell

Honeywell E3Point Manual de usuario

Honeywell

Honeywell C7046C Manual de operación

Honeywell

Honeywell PRO 2000 Series Manual de operación

Honeywell

Honeywell SiX Series Manual de usuario

Honeywell

Honeywell DC311 FB Series Manual de usuario

Honeywell

Honeywell TC840ME Manual de usuario

Honeywell

Honeywell 705 Series Manual de usuario

Honeywell

Honeywell W8703A Manual de usuario

Honeywell

Honeywell DO8EZS Manual de usuario

Honeywell

Honeywell RPW101 Guía del usuario

Honeywell

Honeywell GENT S-Quad Manual de instrucciones

Honeywell

Honeywell DUAL TEC DT8320AF4 Manual de usuario

Honeywell

Honeywell RPW302 Guía de instalación

Manuales populares de Accesorios de otras marcas

Hillco

Hillco 2810 Manual de usuario

Siemens

Siemens QSA2700D Manual del operador

Contours

Contours ZY024 Manual de usuario

Saivod

Saivod VS621 Manual de usuario

Virtuox

Virtuox VirtuCLEAN 2.0 Manual de usuario

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manual de usuario

Z-Wave

Z-Wave HSD-200Z Manual de usuario

turck

turck FMX-IM-2UPLI63FX Manual de usuario

Decagon Devices

Decagon Devices 10HS Manual de usuario

UPPAbaby

UPPAbaby Cup Holder Manual de usuario

Elko

Elko SmartSensor Leakage Wireless Manual de usuario

Grizzly

Grizzly H8371 Manual de usuario

Panasonic

Panasonic HG-T Series Manual de usuario

IFM Electronic

IFM Electronic Efector 250 Series Guía de referencia

DigiDesign

DigiDesign 888/24 I/O Manual de usuario

PROZIS

PROZIS QUAY Manual de usuario

patagonia

patagonia PSI Vest Manual de usuario

SFC Energy

SFC Energy EFOY GO! Manual de usuario