Honeywell Home RDWL311A2000 Instrucciones de funcionamiento

RDWL311A2000

Read before installing

Installation and Operation Guide

Portable Wireless Doorbell

Preparation

Doorbell

Push

Button

Wall

Anchor

Round Head

Screw

Flat Head

Screws

Phillips Screwdriver

Standard Screwdriver

Drill and 1/4 in. (6 mm) drill bit

4 AA alkaline batteries

Push Button Mounting

Bracket

and Adhesive Pad

To install you will need

In the box you will find

The push button supplied with this kit is pre-programmed to operate with the doorbell.

If it is not, see “Connect a Push Button” on page 4.

CR2032

Battery

Overview

Just follow these simple steps:

1. Install batteries.

2. Set up the doorbell and your preferences.

3. Install the doorbell and the push button.

Safety

Before proceeding with the installation, please note the following safety

warnings:

• Always follow the manufacturer’s advice when using power tools and wear

suitable protective equipment (e.g. safety goggles) when drilling holes, etc.

• Before drilling holes in walls, check for hidden electricity cables and water

pipes. The use of a cable/pipe locator is advisable if in doubt.

Install Batteries

1. Open the battery cover and install 4

AA alkaline batteries.

2. Open the battery cover and install the

CR2032 battery.

Change the Tune

Press the Music button to change the doorbell tune.

Every time you press the Music button,

the tune will change. Stop pressing the

Music button when you hear the tune you

want:

Ding Dong

Westminster

Soft Alert

Smart Sax

Setup and Operation

Press the push button to test whether it is paired with the doorbell. The

doorbell will ring. If it does not, see “Connect a Push Button” on page 4.

Install Doorbell

If you are not mounting the doorbell to the wall,

place it where you want it.

1. Mount the screw on to the wall using the



the screw sticking out from the wall.

Drill 1/4 inch holes for the anchor.

2. Hang the doorbell on the screw.

Installation

Choose a location that is not near a heat source or on something that moves

(like a door). For non-mounting locations, choose a place where the doorbell

will be easy to hear.

Install Push Button

1. Mount the push button bracket

in the desired location.

Use the screws



Use the adhesive backing. If

using the adhesive backing,

clean the surface first.

2. Snap the push button onto the

mounting bracket.

–OR–

Note: If you need to remove the push button, use a small

screwdriver to release the tab.

Accessories

You can connect 2 accessories to your doorbell, including other push buttons,

window or door opening sensors, and motion sensors.

If you try to connect more accessories than the max

number, the LED on the side blinks red.

Connect a Motion Sensor

1. Press and hold the Setting button on the doorbell for

three seconds.

The LED on the side turns on with an

amber color.

2. Within 20 seconds of pressing the

Setting button, wave or make some

other kind of motion in front of the

motion sensor.

Connect a Push Button

Follow these steps to change the ring

for an existing doorbell, too.

1. Press and hold the Setting button on

the doorbell for three seconds.

The LED on the side turns on with an

amber color.

2. Press the push button.

3. Within 12 seconds of pressing the

push button, press the Music button

to select the ring for that push

button.

Secret Knock

You can set up a Secret Knock that makes a different ring for each push

button. The Secret Knock is triggered by pressing the push button quickly 3

times.

1. Press the push button 3 times quickly.

2. Within 12 seconds of pressing the push button, press the Music button to

select the ring for the Secret Knock.

Maintenance

Your doorbell and push button require no maintenance except to periodically

change the batteries.

If using the correct batteries, battery life should be approximately:

• Up to 2 years for the doorbell; replace with 4 AA alkaline batteries

• Up to 2 years for the push button; replace with a CR2032 lithium battery

Low Battery Notification

When the doorbell batteries are low, the LED on the side turns on.

When the push button batteries are low, two beep sounds are heard after the

normal tune.

Reset

This process removes all pairings, including the push button that came with

this doorbell:

1. Remove the doorbell battery.

2. Press and hold the Setting button, and replace the battery at the same

time.

3. The doorbell will beep several times rapidly, and is returned to its factory

default settings.

Specications

Doorbell Push Button

Operating Temperature  

Honeywell ActivLink™ 916.8 MHz 916.8 MHz

  

  -

RF Power - <1.2W

  

  

  

Troubleshooting

If Then



1. 



2. 

3. 



 

 



1. 



2. 

3. 





FCC Regulations

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This

device may not cause harmful interference, and (2) this device must accept any interference received, including

interference that may cause undesired operation.





This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part

15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference

in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This

equipment should be installed and operated with a minimum distance of 20 millimeters between the radiator and

your body.

IC Regulations

CAN ICES-3(B)/ NMB-3(B)



two conditions: (1) this device may not cause interference, and (2) this device must accept any interference,

including interference that may cause undesired operation of the device.



The device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance with



This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This

equipment should be installed and operated with a minimum distance of 20 millimeters between the radiator and

your body.

The operation of this equipment is subject to the following two conditions: (1) this equipment or device may not

cause harmful interference, and (2) this equipment or device must accept any interference, including interference

that may cause undesired operation.

33-00185EFS—05 M.S. Rev. 06-19 | Printed in United States

33-00185EFS-05

Resideo Inc., 1985 Douglas Drive North

Golden Valley, MN 55422

www.resideo.com

Warranty

1-year limited warranty

Resideo warrants this product, excluding battery, to be free from defects in workmanship or materials, under



any time during the warranty period the product is determined to be defective due to workmanship or materials,

Resideo shall repair or replace it (at Resideo’s option).

If the product is defective,

(i) return it, with a bill of sale or other dated proof of purchase, to the place from which you purchased it; or





MN 55422, or whether a replacement product can be sent to you.

This warranty does not cover removal or reinstallation costs. This warranty shall not apply if it is shown by Resideo

that the defect was caused by damage which occurred while the product was in the possession of a consumer.

Resideo’s sole responsibility shall be to repair or replace the product within the terms stated above. RESIDEO

SHALL NOT BE LIABLE FOR ANY LOSS OR DAMAGE OF ANY KIND, INCLUDING ANY INCIDENTAL OR

CONSEQUENTIAL DAMAGES RESULTING, DIRECTLY OR INDIRECTLY, FROM ANY BREACH OF ANY WARRANTY,

EXPRESS OR IMPLIED, OR ANY OTHER FAILURE OF THIS PRODUCT.

Some states do not allow the exclusion or limitation of incidental or consequential damages, so this limitation may

not apply to you.

THIS WARRANTY IS THE ONLY EXPRESS WARRANTY RESIDEO MAKES ON THIS PRODUCT. THE DURATION

OF ANY IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A

PARTICULAR PURPOSE, IS HEREBY LIMITED TO THE ONE YEAR DURATION OF THIS WARRANTY. Some states

do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.







RDWL311A2000

Lire avant d’installation

Guide d’installation et d’utilisation

Sonnette sans l portative

Préparation

Sonnette

Bouton-

poussoir

Ancrage

mural

Vis à tête

ronde

Vis à tête

plate

Tournevis cruciforme

Tournevis normal

Perceuse et foret de 6 mm (1/4po)

4 piles alcalines AA

Support de montage

de bouton-poussoir

avec tampon adhésif

Matériel requis

pour l’installation

Vous trouverez dans la boîte

Le bouton-poussoir fourni avec ce nécessaire est préprogrammé pour fonctionner avec la





Pile

CR2032

Aperçu

Suivez simplement ces quelques étapes simples :

1. Installez les piles.

2. Configurez la sonnette et vos préférences.

3. Installez la sonnette et le bouton-poussoir.

Sécurité

Avant de procéder à l’installation, veuillez prendre connaissance des mises en



• Toujours suivre les conseils du fabricant lors de l’utilisation d’outils

électriques et porter un équipement de protection approprié (i.e. lunettes de

sécurité) en perçant des trous, etc.

• Avant de percer des trous dans les murs, vérifier la présence de câbles

électriques ou de conduites d’eau cachés. L’utilisation d’un localisateur de

conduites/de câbles est recommandée en cas de doute.

Installation des piles

1. Ouvrez le couvercle des piles et

installez quatre piles alcalines AA.

2. Ouvrez le couvercle de la pile et

installez la pile CR2032.

Modification de la mélodie



sonnette.

À chaque fois que vous appuyez sur le

bouton Musique, la mélodie change. Arrêtez

d’appuyer sur le bouton Musique lorsque



Ding Dong

Westminster

Alerte douce

Smart Sax

Conguration et fonctionnement

Appuyez sur le bouton-poussoir pour déterminer qu’il est jumelé avec la

sonnette. La sonnette sonne. Si ce n’est pas le cas, consultez la section



Tabla de contenidos

Idiomas:

Otros manuales de Accesorios de Honeywell Home

Honeywell Home

Honeywell Home DC313 HGP2/BS Series Manual de usuario

Honeywell Home

Honeywell Home C7189U Manual de usuario

Honeywell Home

Honeywell Home RDWL313A2000/U Instrucciones de funcionamiento

Honeywell Home

Honeywell Home DC313 HGP2/BS Series Manual de usuario

Honeywell Home

Honeywell Home SiXCT-OD Manual de usuario

Honeywell Home

Honeywell Home CAMIR-8EZS Manual de usuario

Honeywell Home

Honeywell Home DC515 P2/BS Series Manual de usuario

Honeywell Home

Honeywell Home RDWL313P2000 Instrucciones de funcionamiento

Honeywell Home

Honeywell Home DC515 HGP2/BS Series Manual de usuario

Honeywell Home

Honeywell Home 5800SS1 Manual de usuario

Honeywell Home

Honeywell Home 3 Series Instrucciones de funcionamiento

Honeywell Home

Honeywell Home DW311 Series Manual de usuario

Honeywell Home

Honeywell Home RDWL311A2000/U Instrucciones de funcionamiento

Honeywell Home

Honeywell Home RDWL515A2000 Instrucciones de funcionamiento

Honeywell Home

Honeywell Home RDWL515P Instrucciones de funcionamiento

Honeywell Home

Honeywell Home DW915 Series Manual de usuario

Honeywell Home

Honeywell Home RedLINK C7089R3013 Manual de usuario

Honeywell Home

Honeywell Home resideo C7189R3002 Manual de usuario

Honeywell Home

Honeywell Home 5 Series Instrucciones de funcionamiento

Honeywell Home

Honeywell Home DC315 Series Manual de usuario

Honeywell Home

Honeywell Home DC312 P2USB Series Manual de usuario

Honeywell Home

Honeywell Home DC311 P2/BS Series Manual de usuario

Honeywell Home

Honeywell Home DCP917S Manual de usuario

Honeywell Home

Honeywell Home DC311 FB Series Manual de usuario

Manuales populares de Accesorios de otras marcas

Hillco

Hillco 2810 Manual de usuario

Siemens

Siemens QSA2700D Manual del operador

Contours

Contours ZY024 Manual de usuario

Saivod

Saivod VS621 Manual de usuario

Virtuox

Virtuox VirtuCLEAN 2.0 Manual de usuario

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manual de usuario

Z-Wave

Z-Wave HSD-200Z Manual de usuario

turck

turck FMX-IM-2UPLI63FX Manual de usuario

Decagon Devices

Decagon Devices 10HS Manual de usuario

UPPAbaby

UPPAbaby Cup Holder Manual de usuario

Elko

Elko SmartSensor Leakage Wireless Manual de usuario

Grizzly

Grizzly H8371 Manual de usuario

Panasonic

Panasonic HG-T Series Manual de usuario

IFM Electronic

IFM Electronic Efector 250 Series Guía de referencia

DigiDesign

DigiDesign 888/24 I/O Manual de usuario

PROZIS

PROZIS QUAY Manual de usuario

patagonia

patagonia PSI Vest Manual de usuario

SFC Energy

SFC Energy EFOY GO! Manual de usuario