Homemanageables HM-DW001 Manual de usuario

HM-DW001 DOOR/WINDOW SENSOR

This Door/Window Sensor is designed to work with the Homemanageables Starter Kit. The

Door/Window Sensor is a Z-Wave®enabled device (interoperable, two-way RF mesh

networking technology) and is fully compatible with any Z-Wave enabled network. Z-Wave

enabled devices displaying the Z-Wave logo can also be used with it regardless of the

manufacturer, and ours can also be used in other manufacturer’s Z-Wave enabled networks.

Each module in a Homemanageables Network is designed to act as a repeater. Repeaters

will retransmit the RF signal to ensure that the signal is received by its intended destination

by routing the signal around obstacles and radio dead spots.

Adding the Door/Window Sensor to Homemanageables Network

This procedure is intended only for adding the Door/Window Sensor to a Homemanageables

Network. When using another manufacturer’s software or hardware, follow their instructions.

Note that on the rear casing of the Door/Window Sensor, there is a tamper switch which is

used for programming (e.g., adding or removing from a network). To add the Lighting

Module to your Homemanageables Network, select “Add Device” in the Homemanageables

application and follow the instructions.

Installation

The Door/Window Sensor is suitable for mounting in dry, interior locations only.

Note: Take care when fixing the Door/Window Sensor to a metal frame, or mounting within 3

feet of metalwork (i.e. radiators, water pipes, etc.), as this could affect the radio range of the

device. If required, it may be necessary to space the magnet and sensor away from the

metal surface using a plastic or wooden spacer to achieve the necessary radio range.

You can mount the Door/Window Sensor and the magnet using either the enclosed adhesive

tape or screws.

1. Check that the Door/Window Sensor was properly added to the Homemanageables

Network. Align the magnet with the sensor housing (ensure that the matching line on

the magnet is pointing towards and aligned with the line on the sensor) while the tamper

switch is not depressed. The LED should blink once. Remove the magnet, and the

LED will blink again. If this didn’t occur, re-try the “Add Device” process.

2. Remove the fixing screw from the bottom edge of the Door/Window Sensor. Remove the

rear cover.

3. Fit the (3) 1.5V AAA batteries into the battery compartment.

4. Using the rear cover as a template, mark the positions of the holes on the fixed part of

the frame along the opening edge (opposite the hinges).

5. If using the screws to mount the sensor, affix the rear cover to the frame using the two

wood screws (if necessary, use the supplied wall anchors). Do not over tighten the

screws as this may distort or damage the casing. Attach the sensor to the rear cover,

and reinsert the fixing screw.

6. If using the adhesive tape, apply the tape to the rear cover. Align the rear cover with the

marks for the holes, and affix to the frame. Attach the sensor to the rear cover, and

reinsert the fixing screw. Do not over tighten the fixing screw.

7. Align the magnet opposite the sensor. Ensure that the parallel gap between the magnet

and sensor is less than 10mm and that the matching line on the magnet is pointing

towards and aligned with the line on the sensor. Mark the positions of the holes on the

door/window.

8. Affix the magnet to the moving part of the door/window opposite the sensor using the

adhesive tape or fixing screws.

Operation

1. Opening the door/window to separate the magnet from the sensor will send the status of

“Open” to the Homemanageables application.

2. Closing the door/window to align the magnet with the sensor will send the status of

“Closed” to the Homemanageables application.

3. NORMAL OPERATION: AFTER THE SENSOR IS AFFIXED TO THE FRAME, THE

LED WILL NOT LIGHT AS THE TAMPER SWITCH IS DEPRESSED.

Troubleshooting

Symptom Possible Cause Recommendation

Cannot “Add Device” 1. Battery is dead

2. Batteries installed

incorrectly or not seated

properly

1. Replace with new

batteries (always replace

all batteries at same

time)

2. Reinstall batteries

Door/Window Sensor LED

is not illuminating 1. Tamper switch is

depressed.

2. Battery is dead

3. Batteries installed

incorrectly or not seated

properly

1. Release tamper switch

2. Replace with new

batteries (always replace

all batteries at same

time)

3. Reinstall batteries

The Door/Window Sensor

LED is illuminating, but the

Homemanageables

software cannot read from

the sensor

1. The system didn’t add

the module properly

2. Frequency interference

3. Homemanageables USB

stick is not inserted

properly

1. Try the “Add Device”

process again

2. Reinsert the USB stick

3. Wait for a while to re-try

Specifications

FOR INDOOR USE ONLY

Battery 1.5V AAA x 3

Range 100ft. line of sight, in unobstructed environment

Frequency Range 908.42 MHz

*Specifications are subject to change without notice A501110873R01

MADE IN CHINA

Federal Communications Commission Statement

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency energy and, if not installed and

used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the user

is encouraged to try to correct the interference by one of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) this device may not cause harmful interference, and (2) this device must

accept any interference received, including interference that may cause undesired operation.

FCC Caution: Any changes or modifications not expressly approved by the party responsible

for compliance could void the user's authority to operate this equipment.

Limited Warranty

If within one (1) year from the date of purchase, this product fails due to a defect in material or

workmanship under normal use, Homemanageables, Inc. will replace it free of charge.

Homemanageables, Inc. does not issue any refunds. This warranty is extended to the

original end user purchaser only and is not transferable. This warranty does not apply to: (1)

damage to units caused by accident, dropping or abuse in handling, acts of God, or any

negligent use; (2) units which have been subject to unauthorized repair, opened, taken apart,

or otherwise modified; (3) units not used in accordance with instructions; (4) damages

exceeding the cost of the product; (5) sealed lamps and/or lamp bulbs, LED’s, and batteries;

(6) the finish on any portion of the product, such as surface and/or weathering, as this is

considered normal wear and tear; or (7) transit damage, initial installation costs, removal

costs, or reinstallation costs.

Because it is impossible for Homemanageables, Inc. to know the purposes for which you

acquired this product or the uses to which you will put this product, you assume full

responsibility for the selection of the product for its installation and use. While every

reasonable effort has been made to ensure that you will receive a product that you can use

and enjoy, Homemanageables, Inc. does not warrant that the functions of the product will

meet your requirements or that the operation of the product will be uninterrupted or error-free.

HOMEMANAGEABLES IS NOT RESPONSIBLE FOR PROBLEMS OR DAMAGE CAUSED

BY THE INTERACTION OF THE PRODUCT WITH ANY OTHER SOFTWARE OR

HARDWARE.

IN NO EVENT SHALL HOMEMANAGEABLES, INC. BE LIABLE TO YOU OR ANY OTHER

PARTY FOR ANY DIRECT, INDIRECT, GENERAL, SPECIAL, INCIDENTAL,

CONSEQUENTIAL, EXEMPLARY OR OTHER DAMAGES ARISING OUT OF THE USE OR

INABILITY TO USE THE PRODUCT (INCLUDING, BUT NOT LIMITED TO, DAMAGES

FOR INJURY, LOSS OF PROPERTY, BUSINESS PROFITS, BUSINESS INTERRUPTION,

LOSS OF INFORMATION OR ANY OTHER PECUNIARY LOSS), OR FROM ANY BREACH

OF WARRANTY. EVEN IF HOMEMANAGEABLES, INC. HAS BEEN ADVISED OF THE

POSSIBILITY OF SUCH DAMAGES, IN NO CASE SHALL HOMEMANAGEABLES, INC.’S

LIABILITY EXCEED THE AMOUNT YOU PAID FOR THE PRODUCT. ALL IMPLIED

WARRANTIES, INCLUDING THE WARRANTY OF MERCHANTABILITY AND THE

WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY MODIFIED TO

EXIST ONLY AS CONTAINED IN THE LIMITED WARRANTY, AND SHALL BE OF THE

SAME DURATION AS THE WARRANTY PERIOD STATED ABOVE.

For warranty service, call Homemanageables, Inc. customer service toll-free at

1-800-724-0108 to obtain a Return Authorization number. YOU WILL NEED YOUR PROOF

OF PURCHASE. HOMEMANAGEABLES, INC. WILL NOT PROCESS RETURNS

WITHOUT PROOF OF PURCHASE AND A RETURN AUTHORIZATION NUMBER. Mail

the product, postage prepaid, to the address provided by the Customer Service

representative. Mark the Return Authorization number clearly on the outside of the package,

and include a copy of your proof of purchase.

For information on additional Homemanageables accessories, visit us at

www.homemanageables.com.

Homemanageables and Your Life, Only Easier are trademarks or registered trademarks of

Homemanageables, Inc. in the United States and/or other countries. Other brands and products are

trademarks or registered trademarks of their respective holders.

Otros manuales de Accesorios de Homemanageables

Homemanageables

Homemanageables HM-FS001 Manual de usuario

Manuales populares de Accesorios de otras marcas

Hillco

Hillco 2810 Manual de usuario

Siemens

Siemens QSA2700D Manual del operador

Contours

Contours ZY024 Manual de usuario

Saivod

Saivod VS621 Manual de usuario

Virtuox

Virtuox VirtuCLEAN 2.0 Manual de usuario

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manual de usuario

Z-Wave

Z-Wave HSD-200Z Manual de usuario

turck

turck FMX-IM-2UPLI63FX Manual de usuario

Decagon Devices

Decagon Devices 10HS Manual de usuario

UPPAbaby

UPPAbaby Cup Holder Manual de usuario

Elko

Elko SmartSensor Leakage Wireless Manual de usuario

Grizzly

Grizzly H8371 Manual de usuario

Panasonic

Panasonic HG-T Series Manual de usuario

IFM Electronic

IFM Electronic Efector 250 Series Guía de referencia

DigiDesign

DigiDesign 888/24 I/O Manual de usuario

PROZIS

PROZIS QUAY Manual de usuario

patagonia

patagonia PSI Vest Manual de usuario

SFC Energy

SFC Energy EFOY GO! Manual de usuario