Home Decorators Collection Easton Manual de usuario

170 843

Easton

52 in Ceiling Fan

Owner’s Manual

Easton

Ventilador de Techo de 1,32 m

Manual del Propietario

N381-52-CB

120 V~ 60 Hz 33 W

Read and follow all the instructions

before using this product.

Easton by Home Decorators Collection

ongratulations on your

purchase of a Home

Decorators Collection

ceiling fan, Your new fan will be a

beautiful addition to your home,

and will keep you comfortable

throughout the year.

The Home Decorators Collection

Fan Company offers a wide variety

of ceiling fans. We offer combinations

of wood and brass finishes, solid

designer colors, and our unique

glass and crystal designs.

A large selection of light fixtures

and light kits is also available. Ask

your dealer about other accessories

that will allow you to further customize

your fan.

We’re certain that your Home

Decorators Collection fan will

provide you with many years of

comfort, energy savings and

satisfaction. To ensure your

personal safety and to maximize

the performance of your fan, please

read this manual thoroughly.

VENTILADOR DE TECHO / CEILING FAN

Marca / Brand: Home Decorators Collection

Modelo / Model: 170 843 (N381-52-CB)

120 V ~ 60 Hz 33 W

Consumo de energía por unidad de tiempo en operación

(Energy Consumption): 24.4Wh

Importador / Importer: SERVICIOS HOME DEPOT, S. DE R.L. DE C.V.

Ricardo Margain 605, Santa Engracia, San Pedro Garza García, Nuevo León, C.P.

66267 Tel. / Phone: 800 004 6633

Lea y siga todas las instrucciones de seguridad y operación antes de usar este

aparato / Read and follow all the instructions of security and operation before using

this product

Cont. 1 Ventilador / Fan Hecho en / Made in: China

Requiere ensamblaje / Assembly required

52” EASTON

Ceiling Fan by HDC

Date Purchased

Store Purchased

Model No.

Serial No.

Vendor No.

UPC

Table of Contents

Safety Rules . . . . . . . . . . . . . . . . . . . . 1

Unpacking Your Fan . . . . . . . . . . . . . . 2

Installing Your Fan . . . . . . . . . . . . . . . 3

Operation . . . . . . . . . . . . . . . . . . . . 9

Care of Your Fan . . . . . . . . . . . . . . . . 14

Troubleshooting . . . . . . . . . . . . . . . . . 14

Specifications . . . . . . . . . . . . . . . . . . 16

170 843 (N381-52-CB)

548810

840059610085

Thank you for purchasing our ceiling fan. This product has been

manufactured with the highest standards of safety and quality.

Safety Rules - Read and Save These Instructions

To reduce the risk of electric shock, insure electricity has been turned

off at the circuit breaker or fuse box before beginning.

All wiring must be in accordance with the National Electrical Code

“ANSI/NFPA 70” and local electrical codes. Electrical installation should

be performed by a qualified licensed electrician.

The outlet box and support structure must be securely mounted and

capable of reliably supporting a minimum of 35 lbs (15.9 kg) or less.

Use only UL-listed outlet boxes marked “FOR FAN SUPPORT”.

The fan must be mounted with a minimum of 7.55 ft (2.3m) clearance

from the trailing edge of the blades to the floor.

Avoid placing objects in the path of the blades.

To avoid personal injury or damage to the fan and other items, be cautious

when working around or cleaning the fan.

Do not use water or detergents when cleaning the fan or fan blades. A dry

dust cloth or lightly dampened cloth will be suitable for most cleaning.

After making electrical connections, spliced conductors should be turned

upward and pushed carefully up into outlet box. The wires should be spread

apart with the grounded conductor and the equipment-grounding conductor

on one side of the outlet box and ungrounded conductor on the other side of

the outlet box.

All set screws must be checked and retightened where necessary before

installation.

The appliance is not to be used by persons (including children) with reduced

physical, sensory or metal capabilities, or lack of experience and knowledge,

unless they have been given supervision or instruction. Children should be

supervised to ensure that they do not play with the appliance.

Instructions for the use of the apparatus according with NOM-024-SCFI, are

provided with the apparatus.

10.

11.

TO REDUCE THE RISK OF PERSONALL INJURY, DO NOT BEND THE BLADE

ARMS (ALSO REFERRED TO AS FLANGES), WHEN INSTALLING THE

BRACKETS, BALANCING THE BLADES OR CLEANING THE FAN. DO NOT

INSERT FOREIGN OBJECTS IN – BETWEEN ROTATING FAN BLADES.

WARNING

TO REDUCE THE RISK OF ELECTRIC SHOCK, THIS FAN MUST BE INSTALLED

WITH AN ISOLATING WALL CONTROL / SWITCH.

WARNING

TO REDUCE THE RISK OF PERSONAL INJURY, USE ONLY THE SCREWS

PROVIDED WITH THE OUTLET BOX.

CAUTION

CHANGE OR MAINTAIN LED LIGHT KIT SHALL BE PERFORMED BY THE

MANUFACTURER, ITS SERVICE AGENT OR DULY QUALIFIED PERSONS.

NOTE

SUITABLE FOR USE IN DAMP LOCATIONS.

NOTE

Unpacking Your Fan Unpack your fan and check the contents. You should have the following items:

Set of blades (3)

Canopy assembly

Ball/downrod assembly

Coupling cover

Fan motor assembly

Blade support plates with screws and

lock washers (3)

Receiver

Remote control

1.5V AAA batteries (2)

WARNING

DO NOT INSTALL OR USE FAN IF ANY

PART IS DAMAGED OR MISSING.

CALL TOLL FREE 800-004-6633.

Blade Attachment Hardware

(7 Screws, 7 Lock Washers)

Electrical Hardware

(3 Plastic Wire Nuts)

Blade Attachment Hardware (additional)

(1 screw with lock washer)

Electrical Hardware

(3 plastic wire nuts)

Extension cord

Figures 1~3 are examples of different ways to

mount the outlet box.

Outlet box

Figure 2

Figure 1

NOTE: You may need a longer downrod to

maintain proper blade clearance when installing on

a steep, sloped ceiling. The maximum angle

allowable is 18 °.If the canopy touches downrod,

remove the decorative canopy bottom cover and

turn the canopy 180 °before attaching the canopy

to the mounting plate.

To hang your fan where there is an existing fixture

but no ceiling joist, you may need an installation

hanger bar as shown in Figure 4 (available at any

Home Depot store).

Ceiling

mounting

plate

Provide strong support

Recessed

outlet box

Figure 3

Figure 4

Installing Your Fan

If there isn't an existing NOM listed mounting

box, then read the following instructions.

Disconnect the power by removing fuses or

turning off circuit breakers.

Secure the outlet box directly to the building

structure. Use appropriate fasteners and building

materials. The outlet box and its support must be

able to fully support the moving weight of the fan

(at least 35 lbs). Do not use plastic outlet boxes.

Tools Required

Mounting Options

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC

SHOCK OR PERSONAL INJURY, MOUNT FAN

ONLY TO AN OULET BOX MARKED ACCEPTABLE

FOR FAN SUPPORT AND USE THE MOUNTING

SCREWS PROVIDED WITH THE OULET BOX.

OUTLET BOX COMMONLY USED FOR THE

SUPPORT OF LIGHTING FIXTURE MAY NOT BE

ACCEPTABLE FOR FAN SUPPORT AND MAY NEED

TO BE REPLACED. CONSULT A QUALIFIED

ELECTRICIAN IF IN DOUBT.

Phillips screwdriver, straight slot screwdriver, step

ladder and wire cutters.

Attaching the Fan Blades

Figure 5

REMEMBER to turn off the power. Follow the

steps below to hang your fan properly.

Hanging the Fan

Remove the canopy bottom cover from the

canopy by turning the cover counterclockwise.

(Figure 6)

Remove the mounting bracket from the canopy

by loosening the slotted canopy mounting screws

a half turn from the screw head. Next, turn the

canopy counterclockwise to remove the

mounting bracket from the canopy. (Figure 6)

Remove the cotter pin and clevis pin, and loosen

the two collar set screws from the fan motor

assembly collar. (Figure 7)

Take out the setscrew located in the hanger ball,

lower the hanger ball and remove the cross pin.

Remove the hanger ball from the hanger

ball/downrod assembly. (Figure 7)

Remove the ground lead from the downrod

assembly. (Figure 7)

NOTE:If a longer downrod is needed, take

out the screw located in the hanger ball, lower

the hanger ball and remove the pin, remove all

3 pieces from the downrod and assemble them

onto the new longer downrod before proceeding

step 3. (The longer downrod is available at

any Home Depot store)

Carefully feed the motor wires up through the

downrod. Thread the downrod into the collar.

Align the holes and replace the clevis pin and

cotter pin. Tighten the two collar setscrews.

(Figure 8)

Slip the coupling cover, the canopy bottom

cover, and the canopy onto the downrod.

Carefully reinstall the hanger ball the ground

lead onto the downrod, being sure that the

cross pin is in the correct position, the

setscrew is tightened and wires are not twisted.

(Figure 8)

Figure 6

WARNING

FAILURE TO PROPERLY INSTALL COTTER

PIN AS NOTED IN STEP 6 COULD RESULT IN

FAN LOOSENING AND POSSIBLY FALLING.

Mounting

Bracket

Ceiling Canopy

Canopy Bottom

Cover

Attach the blade to the motor. Align the holes in

the blade support plate, the blade, and the fan

motor assenbly and secure with the blade

attachment screws and lock washers. (Figure 5)

Repeat this procedure with the remaining

blades.

WARNING

TO REDUCE THE RISK OF PERSONAL INJURY,

DO NOT BEND THE BLADES WHILE INSTALL-

ING, BALANCING THE BLADES, OR CLEANING

THE FAN. DO NO INSERT FOREIGN OBJECTS

BETWEEN ROTATING FAN BLADES.

Blade

Motor

Blade

Support

Plate

Screw

Figure 8

Figure 7

Installing Fan to the

Electrical Box

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC

SHOCK OR OTHER PERSONAL INJURY. MOUNT

FAN ONLY TO AN OUTLET BOX OR SUPPORTING

SYSTEM MARKED ACCEPTABLE FOR FAN

SUPPORT AND USE THE MOUNTING SCREWS

PROVIDED WITH THE OUTLET BOX.

Pass the 120-volt supply wires through the

center hole in the ceiling mounting bracket as

shown in Figure 9.

Attach the mounting bracket on the outlet box

by sliding the mounting bracket over the screws

provided with the outlet box. (Figure 9)

Securely tighten the two mounting screws.

(Figure 9)

Carefully lift the fan assembly up to the ceiling

mounting bracket and seat the hanger ball in

the mounting bracket socket. Make sure the tab

on the mounting bracket socket is properly

seated in the groove in the hanger ball (Figure

10). This will help to balance the ceiling fan.

Clevis pin

Cotter pin

Hanger ball DownrodDownrod

Cross pin

Set screw

Ground leadGround lead

Motor collar

Set screws

Clevis pin

Tighten

screws

firmly

Ceiling canopy

Pin in locked

position

Hanger ball

Set screw

Cross pin

Downrod

Ground lead

Coupling cover

Clevis pin

Canopy Bottom

Cover

Motor wires

Motor

collar Cotter pin

Cotter pin

Extension cord

WARNING

THE TAB IN THE RING MUST REST IN THE

GROOVE OF THE HANGER BALL AS FIGURE 10.

FAILURE TO PROPERLY SEAT THE TAB IN THE

GROOVE COULD CAUSE DAMAGE TO WIRING.

Figure 10

Figure 9

120V

Wires

Ceiling mounting

bracket

NOM listed

outlet box

Mounting

screws (Supplied

with outlet box)

Making the Electrical

Connections

WARNING

CHECK TO SEE THAT ALL CONNECTIONS ARE

TIGHT, INCLUDING GROUND, AND THAT NO

BARE WIRE IS VISIBLE AT THE WIRE NUTS,

EXCEPT FOR THE GROUND WIRE.

NOTE

THE FAN MUST BE INSTALLED AT A MAXIMUM

DISTANCE OF 20 FT. FROM THE REMOTE

CONTROL FOR PROPER SIGNAL TRANSMISSION

BETWEEN THE REMOTE CONTROL AND THE

FAN'S RECEIVING UNIT.

NOTE

IF A LONGER DOWNROD (NOT INCLUDED) IS

NEEDED, USE THE EXTENSION CORD TO

CONNECT WITH THE MOTOR WIRES AND

RECEIVER.

CAUTION

DO NOT USE WITH A WALL LIGHT DIMMER

SWITCH.

If you feel you do not have enough electrical wiring

knowledge or experience, have your fan installed by

a licensed electrician.

Follow the steps below to connect the fan to your

household wiring. Use the plastic wire nuts with

your fan. Secure the plastic wire nuts with electrical

tape. Make sure there are no loose strands or

connections.

1. Insert the receiver into the mounting bracket

with the flat side of the receiver facing the ceiling.

2. Make wire connections from the fan to the

receiver.

From Fan To Receiver

3-Pin Connector--------------- 3-Pin Connector

3. Make wire connections from the receiver and

fan to the outlet box as follows, using the wire nuts .

From Receiver To Outlet Box

Black Wire "AC in L" -------- Black Wire (Hot)

White Wire "AC in N" ------- White Wire (Neutral)

Green Wires* ------------------ Green or Bare Wire

(Ground)

From Fan To Outlet Box

Green Wires* ----------------- Green or Bare Wire

(Ground)

* There are four green grounding leads: one from

the mounting bracket and one from the hanger

ball/downrod assembly and two from the receiver if

installed.

4. Turn the wire nut connections upward,

spreading them apart so the green (ground) and

white wires will be on one side of the outlet box and

the black and blue wires will be on the other side.

Carefully tuck the connections up into the outlet

box.

Groove

Tab

Tabla de contenidos

Otros manuales de Admirador de Home Decorators Collection

Home Decorators Collection

Home Decorators Collection HERALD AM429-BN Manual de usuario

Home Decorators Collection

Home Decorators Collection FOLSOM YG523-BN Manual de usuario

Home Decorators Collection

Home Decorators Collection GAZELLE 51550 Manual de usuario

Home Decorators Collection

Home Decorators Collection AM589H-EB Manual de usuario

Home Decorators Collection

Home Decorators Collection CANTERBURY SW17B2L BN Manual de usuario

Home Decorators Collection

Home Decorators Collection GRENADA YG522-BN Manual de usuario

Home Decorators Collection

Home Decorators Collection Windward 91165 Manual de usuario

Home Decorators Collection

Home Decorators Collection Kayden 52060 Manual de usuario

Home Decorators Collection

Home Decorators Collection RIMGATE 56048 Manual de usuario

Home Decorators Collection

Home Decorators Collection BENTLEY III Manual de usuario

Home Decorators Collection

Home Decorators Collection EASTON N381B-BN Manual de usuario

Home Decorators Collection

Home Decorators Collection Chartwell Manual de usuario

Home Decorators Collection

Home Decorators Collection KELBRA YG439-BN Manual de usuario

Home Decorators Collection

Home Decorators Collection CHASEWOOD 59724 Manual de usuario

Home Decorators Collection

Home Decorators Collection 68-ATRDC Manual de usuario

Home Decorators Collection

Home Decorators Collection BENTLEY III AM183W-BN Manual de usuario

Home Decorators Collection

Home Decorators Collection VENDOME 51884 Manual de usuario

Home Decorators Collection

Home Decorators Collection VINWOOD 56001 Manual de usuario

Home Decorators Collection

Home Decorators Collection MONTEL Manual de usuario

Home Decorators Collection

Home Decorators Collection YG726-NI Manual de usuario

Home Decorators Collection

Home Decorators Collection MOLIQUE AM128-NI Manual de usuario

Home Decorators Collection

Home Decorators Collection DRISKOL Manual de usuario

Home Decorators Collection

Home Decorators Collection RAILEY YG446-BN Manual de usuario

Home Decorators Collection

Home Decorators Collection YG768A-MBK Manual de usuario

Manuales populares de Admirador de otras marcas

ELTA FANS

ELTA FANS H03VV-F Manual de usuario

Hunter

Hunter 20714 Manual de instrucciones

Emerson

Emerson CARRERA VERANDA CF542ORB00 Manual de usuario

Hunter

Hunter Caraway Manual de instrucciones

Panasonic

Panasonic FV-15NLFS1 Manual de usuario

Kompernass

Kompernass KH 1150 Manual de usuario

VES

VES FALA100/12V/TR Manual de usuario

Vertiv

Vertiv Liebert DCD Manual de usuario

Westinghouse

Westinghouse GFP Series Manual de usuario

Venmar

Venmar KUBIX HRV PLUS Series Manual de usuario

Maico

Maico ECR 31 Manual de usuario

Sonnenkonig

Sonnenkonig Dinky Manual de usuario

S&P

S&P ECOWATT HXBR Manual de usuario

Wider

Wider IMP03369BH Manual de usuario

Panasonic

Panasonic F-60DHN Manual de usuario

Hinkley

Hinkley HIGHLAND Manual de usuario

Broan

Broan 766BN Manual de usuario

Premium

Premium PFS16022 Instrucciones de montaje