Hobby King EPP-P51D Manual de usuario

EPP－P51D

EPP－P51DEPP－P51D

INSTRUCTIONS

ALMOST UNBREAKABLE

Before operating this unit, please read these instructions completely.

Features:

Epp-P51D is epp fun fighters for outdoor flying.

Profile-scale high performance.Model is produced

by modern technology on CNC machines from EPP

“almost unbreakable” material. The flying time of

P51D is between 8 to 15 minutes, it depends on the

flying figures. It is very easy to land with the model ,

you are able to do it into your hand if you want like

with hand launch glider.

ProductSpecifications:

Fuselage length: 680mm (26.8in.)

Wingspan: 840mm (33.0in.)

Flying Weight:320-350g (with battery)

Motor: 2208 KV 1450

ESC: 20Amp

Propeller: GWS 8040

Servo: 8g micro servo * 3pcs

Radio: 4/more channels

Battery: 11.1V 600-1000mAh Li-po 20C

ALMOST UNBREAKABLE

CG Position:

45-55mm from the leading edge of the wing,.

Recommended FlyingSetup

Max servo travelofaileron:15degreesupand15degreesdown（8mm）

Max servo travelofelevator:15 degreesupand15degreesdown（10mm）

Max servo travel of rudder: 20degrees left and 20 degrees right （

Do not fly under the conditions below

Wind strong enough to make the trees rustle

A street with many trees or street lamps

Close to high voltage electrical wires

High Population density areas

Cautions for flying

front lawns and parks make excellent flying areas. Make sure you

have permission to fly and follow safety guidelines set by local

authorities. The calmer the wind, the better!

Note for Storage

Please disconnect the lipo packs when finished flying

Do not press or crush the airplane when storing

The best way to store is to hang the airplane to keep the control

surface rigid

45－55mm45－55mm

Body parts included in the packing

1 Fuselage 1pcs

2 canopy 1pcs

3 Wing with aileron (right and left) 2pcs

4 Elevator (stabilizer) 1pcs

5 vertical fin 1pcs

A Motor mount 1pcs

B Extension of the arm 1pcs

C pushrod connector 4pcs

D Screw 5pcs

E Pvc 1pcs

F Control arm 4pcs

Carbon fiber fittings

Glass fiber rod 3pcs diameter．1．5mm＊800ｍm（L）

Plastic tube 2pcs size: 2*230mm

Z wire 2pcs 0．8mm＊360mm

Z wire 2pcs 1.2 mm *220mm

The items below are required for assembly

Cut a a straight slot on the fuselage to 580mm by knife as picture

shown. The slot must be 3mm deep and ensure the 1.5mm carbon

rod inset.

press the wire into the slot．

On the flat board glue the carbon rod into fuselage using CA glue．

In the same manner install it on the opposite side of the fuselage

Glue the motor mount as shown .Use CA glue

Insert motor mount into the fuselage .use CA glue.

Screw motor into the motor mount , using 4pcs screws.

Cut opening for ESC .insert ESC into opening –the hole must be

about 1mm smaller,The fuselage foam will hold the ESC in the right

position.

Using sharp knife cut an opening for rudder and elevator servos

and for receiver .

The opening for servos must be 1mm smaller from each side .

Insert the servos into the hole as shown .use CA glue .

Install the pushrod connector to the servo arm, insert the quick lock

onto the pushrod connector .

Use your radio system and determine which hole in the servo arms

will give the desired control throw. Install the servo arms on the

servos.

Into the fuselage drill 8mm deep slot for servo cable of the ESC

.Install the servo cable into this slot for receiver.

Using sharp knife cut the slot for the tube at left side of the fuselage

.the slot must be 3mm deep .position slot as shown.

60mm

Press the tube into the slot in fuselage as shown .glue it using CA

glue .

Install the other end of the Z wire (elevator pushrod) to the elevator

servo arm．

Install the other end of the Z wire (rudder pushrod) to the rudder servo

arm

Using sharp knife cut an opening for ailerons servo .The opening

must be 1mm smaller from each side.

15mm

Into the fuselage drill the 8mm hole for aileron servo cable up to

the space for receiver.

Glue the extension of the servo arm onto the ailerons servo arm

using CA glue.

Before gluing rough the arm and extension.

Insert connectors into extension of the servo horn .

Insert the ailerons servo into the hole and put through the servo

cable into the opening for receiver .glue the servo using fusion

glue.

Using sharp knife cut an opening for ailerons servo horn.

Switch on the RC-set for to have the servo in neutral .install the

servo horn on the servo.

Insert the receiver into place .the fuselage foam will hold it in place

.plug the elevator ,rudder and aileron servos and ESC conectors

into receiver.

Put the servo cables into the opening around the receiver.

The horizontal stabilizer into the fuselage glue arround the edge

with CA glue .check the perpendicularity as shown .

Put the elevator horn onto the “Z” wire as shown .mark the position

for slot .Cut the slot 6mm deep.

Glue the elevator horn into the elevator with CA glue as shown.

Glue vertical fin on the fuselage using CA glue .Check the

perpendicularity and alignment as shown.

Bend the elevator as shown . put the rudder horn onto the “Z”wire

as shown .mark the position for slot .cut the slot 6mm deep.glue the

horn into the rudder with CA glue as shown .

Switch on the RC set. Put the control surfaces to the neutral as

shown . Tighten the connector screws .cut the pushrods as shown .

Put control surfaces into neutral

Glue the wing panels together using CA glue .

40mm 40mm

800mm

Cut the slot in the wing using sharp knife .the slot must be 3mm

deep and 800mm length.

Press the wire into slot in the wing .

Glue the wire into upper side of the wing using CA glue and activator

spray .

Use the same procedure glue the wire on the bottom side of the wing .

12mm

Cut a slots in the ailerons of wing for the control horns as shown .

Glue the control horns into the ailerons using CA glue and activator

spray .

BA＝B

90 C＝D

Insert wings into the fuselage as shown . check if the wings is the

centre and in the right alignment .Also check if the wing is

perpendicular to the fuselage side .

Glue the wing in place using CA glue . Apply glue at the top and

than to the bottom (as shown)

Insert the control wires into the ailerons horns and into pushrod

connector as shown .switch on the RC-system for to have the servo

in neutral .put the ailerons in neutral .Now the pushrod connectors

screws must be tightened.

Hollow out the canopy with sharp knife and make enough space for

servo arm working

44mm

Install the canopy to the fuselage with screw and connector

Install the the propeller and spinner to the motor .tighten properly.

Moving the accu pack make the model balance .

cut opening In the fuselage for accu pack –the hole must be about

1mm smaller of each side ,the fuselage foam will hold the accu

pack in the right position.

The accu pack press into the hole in fuselage .

FinalCheck

Checkthe model.Itmustbesymmetrical andnot twisted.

Radiocontrol setinstallation

review top and side view, showing a basic radio installation. Put accu

pack in fuselage as shown. Accu pack will be used for balancing the

P51D. Use instruction guidefor speed controllerfor operating with electro

powerset.

Centre of gravity

Support your model with your fingertips. It should balance, slightly nose

down, when your finger tips are 45-55mm behind the leading edge of the

wing. Move the battery to balance your modell properly. Do not try to fly

anout-of balancedmodel, asitwillcrash!

Flying

Check each control surface for the correct movement and adjust

pushrods. Checking running of the motor. For taking of you need a flying

fieldabout 100m longwithout treesaround. Holdyour modelon the hand ,

put ¡±full gas¡±.Throw the model in the air little bit nose up .Move elevator a

littlebitupand warbirdwillbein theair .

Fix the end of PVC without hole to the front of the canopy with glue.

Otros manuales de Juguete de Hobby King

Hobby King

Hobby King Decathlon-46 Manual de usuario

Hobby King

Hobby King Airoso F3A Manual de usuario

Hobby King

Hobby King TRAINSTAR Manual de usuario

Hobby King

Hobby King PT-17 Manual de usuario

Hobby King

Hobby King Fokker Dr.I Manual de usuario

Hobby King

Hobby King Li13der-EP Manual de usuario

Hobby King

Hobby King EXTRA260P Manual de usuario

Hobby King

Hobby King Mig-15 EDF Manual de usuario

Hobby King

Hobby King WARGO YAK55 Manual de usuario

Hobby King

Hobby King YAK54 20CC EP Manual de usuario

Hobby King

Hobby King SuperG Manual de usuario

Hobby King

Hobby King J3 CUB Manual de usuario

Hobby King

Hobby King Gee Bee R3 Manual de usuario

Hobby King

Hobby King ViperJet G500 Manual de usuario

Hobby King

Hobby King Tanager Glider Manual de usuario

Hobby King

Hobby King Estrella Sport-50E Manual de usuario

Hobby King

Hobby King Skipper 40228 Manual de usuario

Hobby King

Hobby King SBACH 55" Manual de usuario

Hobby King

Hobby King J3 NAVY CUB Manual de usuario

Hobby King

Hobby King 450 Manual de usuario

Hobby King

Hobby King Cessna 195 Manual de usuario

Hobby King

Hobby King EXTRA260P Manual de usuario

Hobby King

Hobby King DH 82 Tiger Moth Manual de usuario

Hobby King

Hobby King MXS-R 64 Manual de usuario

Manuales populares de Juguete de otras marcas

marklin

marklin 37321 Manual de usuario

Canon

Canon PAPER CRAFT Manual de usuario

GREAT PLANES

GREAT PLANES Pitts M-12S Manual de usuario

NOCH

NOCH 14261 Manual de usuario

Hausler

Hausler 450 SE V2 Manual de usuario

Dynaflite

Dynaflite Daydream Manual de usuario

MiniacRC

MiniacRC MIGHTY MINI P40 WARHAWK Manual

Kenner

Kenner Batman 63651 Manual de usuario

LEGO

LEGO 8527 Manual de usuario

iKarus

iKarus ECO 8 Manual de usuario

Multiplex

Multiplex EasyStar II Manual de instrucciones

Walkera

Walkera 38 Manual de instrucciones

Hasbro

Hasbro TRANSFORMERS BUMBLEBEE Manual de usuario

MD MXION SWD Manual de usuario

Mattel

Mattel Disney Pixar Cars Cozy Cone Spiral Rampway Manual de usuario

marklin

marklin 39671 Manual de usuario

Meccano

Meccano 15103 Manual de usuario

LEGO

LEGO TECHNIC 8735 Manual de usuario