HMS AnyBus-X AB7607 Manual de usuario
Anybus-X
Ethernet to DeviceNet Gateway
Installation Guide
AB7607
Part no. SP0848
Rev. 1.23
Installation Guide 1
© 2005-2009 HMS Industrial Networks.
Table of Contents
Installation Items Checklist ............................................... 2
Installation and operation requirements .......................... 2
Connectors.......................................................................... 3
Connecting Power .............................................................. 3
Connecting to DeviceNet ................................................... 4
DeviceNet Connector ..................................................... 4
Setting the MAC ID and Baud Rate ............................... 4
Connecting to Ethernet ...................................................... 6
Ethernet Connector ........................................................ 6
Setting the IP Address ................................................... 6
Configuration Port Connector ......................................... 11
Further Technical Information......................................... 12
Technical Specifications.................................................. 12
Environmental Specifications ....................................... 12
EMC Directive Compliance .......................................... 12
Electrical Specifications................................................ 12
Warranty ............................................................................ 13
Support .............................................................................. 14
Installation Guide 2
© 2005-2009 HMS Industrial Networks.
Installation Items Checklist
• Anybus-X Ethernet to DeviceNet Gateway (part number AB7607).
• Anybus-X Ethernet to DeviceNet Gateway User Manual downloadable from
http://www.anybus.com and go to the support section
• Power cable for connection to supplied 2 position connector.
• DeviceNet cable for connection to supplied 5 position connector.
• Ethernet cable for connection to RJ-45 connector.
• DeviceNet configuration tool such as RSNetworx for DeviceNet or NetTool-
DN.
• EDS file, AB7607.eds, downloadable fromhttp://www.anybus.com and go to the
support section.
Installation and operation requirements
Power, input and output (I/O) wiring must be in
accordance with Class 1, Division 2 wiring methods
– article 501-4 (b) of the National Electric code,
NFPA 70 and in accordance with local codes.
Warning – Explosion Hazard – Substitution of
components may impair suitability for class 1,
Division 2.
Warning – Explosion Hazard – When in hazardous
locations turn off power before replacing or wiring
modules.
Warning – Explosion Hazard – Do not disconnect
equipment unless power has been switched off or the
area is known to be nonhazardous.
Terminal tightening torque must be between 5 – 7
lbs-in (0,5-0,8 Nm).
For use in Class 2 circuits only.
Suitable for Surrounding temperature of 65 C max.
Use 60/75 C copper wire only.
Installation Guide 3
© 2005-2009 HMS Industrial Networks.
Connectors
Connecting Power
The Anybus-X requires 24 volts DC power on the 2 position terminal block con-
nector.
DeviceNet Power Aux RS-232
Ethernet
Ethernet IP Address
24VDC Common
24 VDC +
Installation Guide 4
© 2005-2009 HMS Industrial Networks.
Connecting to DeviceNet
DeviceNet Connector
DeviceNet is connected to the 5 position terminal block connector.
A 120 ohm termination resistor (not provided) between CAN High and CAN Low
may be required for proper network termination.
Setting the MAC ID and Baud Rate
Factory default DeviceNet settings are:
MAC ID 63
Baud Rate 125K
(Red) Net Power 24VDC +
(Black) Net Power 24VDC Common
(White) CAN High
(Blue) CAN Low
CAN Shield
Installation Guide 5
© 2005-2009 HMS Industrial Networks.
Setting MAC ID and Baud Rate Using the Anybus-X Configuration Tool
The DeviceNet configuration can be set using the BWConfig tool. When
launched, the tool (shown below) will allow the DeviceNet configuration to be
edited and downloaded to the module. Once the configuration has been down-
loaded, the Anybus-X will be reset automatically by the tool. See the Configura-
tion section of the user manual for complete details on using BWConfig.
Setting MAC ID and Baud Rate Using a Node Commissioning Tool
A DeviceNet node commissioning utility, such as RSNetworx or NetTool-DN,
may be used to change the MAC ID and baud rate settings. Refer to the user doc-
umentation for the tool being used, or the Anybus-X user manual for more details.
Installation Guide 6
© 2005-2009 HMS Industrial Networks.
Connecting to Ethernet
Ethernet Connector
The Ethernet cable is connected to the RJ45 connector on the end of the module.
Setting the IP Address
Setting the IP Address Using the Anybus-X Configuration Tool
The Ethernet configuration can be set using the BWConfig tool. When launched,
the tool (shown above) will allow the Ethernet configuration to be edited and
downloaded to the module. Once the configuration has been downloaded, the
Anybus-X will be reset automatically by the tool. See the Configuration section
of the user manual for complete details on using BWConfig.
Setting the IP Address Using DHCP/BOOTP
When DHCP/BOOTP is enabled, the IP address settings will be configured by the
DHCP or BOOTP server on the network.
This is the default setting of the Anybus-X when it is shipped. The DHCP option
is enabled or disabled using the Anybus-X’s Settings web page.
Installation Guide 7
© 2005-2009 HMS Industrial Networks.
Setting the IP Address with the Configuration Switch
The IP configuration switch is an 8 position DIP switch located on the end of the
module. If any of the 8 switches are in the ON position, the IP address will be set
as follows:
IP Address: 192.168.1.n
Subnet Mask: 255.255.255.0
Gateway Address: 0.0.0.0
Where nis the value represented in binary by the DIP switch.
This address is a private address and can only be used on a local intranet.
Example:
The switch represents the binary value 00010100, or 20 decimal. (The switch
position is shown in White in the diagram.)
The resulting IP address will be 192.168.1.20.
Installation Guide 8
© 2005-2009 HMS Industrial Networks.
Setting the IP Address Using ARP
The IP address can be set using the Ping command from a PC after the module’s
Ethernet address is entered into the ARP table.
All 8 switches of the IP Address Configuration DIP switch must be set to the ON
position prior to powering up the module. The Arp/Ping feature is disabled if any
switch is in the OFF position.
On a PC connected to the Anybus-X using Ethernet bring up a MS DOS™ win-
dow type:
arp -s <Desired IP Address> <Module Ethernet Address>
The MAC address can be found on the back of the module. Next type:
ping <Desired IP Address>
This will set the IP address of the module. Now type:
arp -d <Desired IP address>
to remove the static entry from the ARP table.
Example:
The following commands will set the IP address of a Anybus-X with MAC
address 00-30-11-02-00-5E to 65.106.34.252.
arp -s 65.106.34.252 00-30-11-02-00-5e
ping 65.106.34.252
arp -d 65.106.34.252
Installation Guide 9
© 2005-2009 HMS Industrial Networks.
Setting the IP Address Using the Web Page
The IP address can also be configured using the Status and Settings web page. The
web pages are accessed by typing the current IP address of the Anybus-X into a
web browser URL. The Status and Settings web page appears as shown below.
Otros manuales para AnyBus-X AB7607
1
Tabla de contenidos
Otros manuales de Hardware de red de HMS
HMS
HMS FLB 3271 Manual de usuario
HMS
HMS Anybus Wireless Bridge II Guía del usuario
HMS
HMS IXXAT CANnector Bridge Manual de usuario
HMS
HMS Anybus ABC4012 Guía del usuario
HMS
HMS Anybus Wireless Bolt Series Manual de usuario
HMS
HMS Anybus Wireless Bolt Serial Manual de usuario
HMS
HMS Anybus AB7665 Manual de usuario
HMS
HMS Anybus Wireless Bolt Series Guía del usuario
HMS
HMS Anybus Wireless Bridge II Manual de usuario
HMS
HMS Anybus 021440 Manual de usuario
HMS
HMS Anybus Wireless Bolt CAN SP2937 Guía del usuario
HMS
HMS Ewon Flexy Series Manual de usuario
HMS
HMS Anybus X-gateway Modbus-TCP Manual de usuario
HMS
HMS eWON Cosy 131 Manual de usuario
HMS
HMS Ixxat CAN@net NT 200 Manual de usuario
HMS
HMS Anybus Wireless Bolt RJ45 PoE Manual de usuario
HMS
HMS Anybus Wireless Bridge II Guía del usuario
HMS
HMS Anybus Wireless Bolt II Guía del usuario
Manuales populares de Hardware de red de otras marcas
Matrix Switch Corporation
Matrix Switch Corporation MSC-HD161DEL Manual de usuario
B&B Electronics
B&B Electronics ZXT9-IO-222R2 Manual de usuario
Yudor
Yudor YDS-16 Manual de usuario
D-Link
D-Link ShareCenter DNS-320L Manual de usuario
Samsung
Samsung ES1642dc Instrucciones de uso
Honeywell Home
Honeywell Home LTEM-PV Instrucciones de montaje
