HM Electronics DX100 Manual de usuario

HME# 400G573

Rev −11/1/05

DX100

Wireless Intercom

Operating Instructions

Table of Contents

SECTION 1. INTRODUCTION .......................................................................................................................1

EQUIPMENT IDENTIFICATION .......................................................................................................................2

MAIN EQUIPMENT FEATURES .......................................................................................................................3

Base Station Features ........................................................................................................................................3

Beltpac Features ................................................................................................................................................3

SECTION 2. EQUIPMENT SETUP.................................................................................................................4

BELTPAC BATTERY CHARGER SETUP......................................................................................................... 4

Connect AC Power Supply................................................................................................................................ 4

Charge Batteries ................................................................................................................................................4

BASE STATION SETUP......................................................................................................................................5

Equipment Connections..................................................................................................................................... 5

BELTPAC SETUP AND REGISTRATION.........................................................................................................7

Set Up Beltpacs .................................................................................................................................................7

Register Beltpacs...............................................................................................................................................7

SECTION 3. EQUIPMENT OPERATION.....................................................................................................9

BASE STATION OPERATION ...........................................................................................................................9

Controls and Indicators......................................................................................................................................9

Low Battery Indicator........................................................................................................................................9

BELTPAC OPERATION.................................................................................................................................... 10

Beltpac Controls and Indicator Lights.............................................................................................................10

Power On/Off ..............................................................................................................................................10

Enable Hands-Free Mode............................................................................................................................10

ISO (Isolate) and IC (Intercom)...................................................................................................................10

Volume Up/Down .......................................................................................................................................11

Microphone Gain Adjustment .........................................................................................................................11

Batteries...........................................................................................................................................................11

SECTION 4. TROUBLESHOOTING............................................................................................................12

SECTION 5. TECHNICAL DATA.................................................................................................................13

EQUIPMENT SPECIFICATIONS .....................................................................................................................13

Base Station.....................................................................................................................................................13

Beltpac............................................................................................................................................................. 14

DISPOSAL OF WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT................................................. 15

Illustrations in this publication are approximate representations of the actual

equipment, and may not be exactly as the equipment appears.

HM Electronics, Inc. is not responsible for equipment malfunctions due to

erroneous translation of its publications from their original English version.

INFORMATION TO USER

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may

not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause

undesired operation.

This equipment has been tested and found to comply with the limits for Class B Digital Device, pursuant to Part 15

of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a

residential installation. This equipment generates and can radiate radio frequency energy and, if not installed and

used in accordance with the instructions, may cause harmful interference to radio communications. However, there

is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the following measures.

• Reorient or relocate the receiving antenna

• Increase the separation between the equipment and receiver

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected

• Consult the dealer or an experienced radio/TV technician for help

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s

authority to operate the equipment.

Hereby, HM Electronics, Inc. declares that the DX100 is in compliance with the essential requirements and other relevant

provisions of R&TTE Directive 1999/5/EC.

This product operates in the 2400 to 2483.5 MHz frequency range. The use of this frequency range is not yet harmonized

between all countries. Some countries may restrict the use of a portion of this band or impose other restriction relating to power

level or use. You should contact your Spectrum authority to determine possible restrictions.

MANDATORY SAFETY INSTRUCTIONS

FOR INSTALLERS AND USERS

Use only manufacturer or dealer supplied antennas.

The Federal Communications Commission has adopted a safety standard for human exposure to RF (Radio Frequency)

energy, which is below the OSHA (Occupational Safety and Health Act) limits.

The term “IC:” before the certification/registration number only signifies that the Industry Canada technical specifications

were met.

Base Station Antenna minimum safe distance: 7.9 inches (20 cm) at 100% duty cycle.

Base Station Antenna gain: This device has been designed to operate with an antenna having a maximum gain of up to

2dBi.

Antenna mounting: The antenna(s) used for the base transmitter must be installed to provide a separation distance of at

least 7.9 inches (20 cm) from all persons and must not be co-located or operating in conjunction with any other antenna or

transmitter.

Antenna substitution: Do not substitute any antenna for the one supplied by the manufacturer or radio dealer. You may

be exposing person or persons to excess radio frequency radiation. You may contact your radio dealer or the manufacturer

for further instructions.

WARNING: Maintain a separation distance from the base station transmit antenna to a person(s) of at least 7.9 inches (20

cm) at 100% duty cycle.

You, as the qualified end-user of this radio device must control the exposure conditions of bystanders to ensure the

minimum separation distance (above) is maintained between the antenna and nearby persons for satisfying RF exposure

compliance. The operation of this transmitter must satisfy the requirements of Occupational/Controlled Exposure

Environment, for work-related use. Transmit only when person(s) are at least the minimum distance from the properly

installed, externally mounted antenna.

LIMITED WARRANTY

HM Electronics, Inc. (“HME”) warrants the DX100 for a period of two (2) years* from the date of purchase

against defects in materials or workmanship provided it was purchased from an authorized dealer. During the

warranty period, defective HME Products will be repaired without charge for parts and labor. Simply return the

defective HME Product with your sales slip as proof of the date of purchase. If a defective HME Product is

returned prepaid to HME or an authorized HME service center, it will be repaired and returned prepaid.

Replacement of nonconforming goods and repair of defective HME Products are the sole and exclusive remedies

available under this warranty.

This warranty shall be void if (a) the HME Products have been tampered with, neglected, modified, abused or

misused; (b) anyone other than HME employees or authorized HME service representatives provide service on or

to the HME Products; or (c) the serial numbers are not intact.

THIS WARRANTY COVERS HME PRODUCTS, AND IS NOT EXTENDED TO ASSOCIATED NON-HME

PRODUCTS OR ACCESSORIES, OR ANY DAMAGE TO HME PRODUCTS CAUSED BY SUCH NON-

HME PRODUCTS OR ACCESSORIES. IN NO EVENT WILL HME BE LIABLE FOR INCIDENTAL OR

CONSEQUENTIAL DAMAGES, OR LOSS OF PROFITS ARISING FROM THE USE OF OR INABILITY TO

USE ANY HME PRODUCTS, OR FROM ACCIDENTS OR ACTS OF GOD.

HME MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WARRANTIES OF

MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, WITH RESPECT TO HME

PRODUCTS EXCEPT AS SPECIFICALLY SET FORTH ABOVE.

This warranty is provided to the original purchaser of the HME Products described on this packing list and is non-

transferable without the written permission of HME.

RETURN POLICY:

ALL SALES FINAL. No returns will be accepted (except for nonconforming goods as specified above) unless

HME authorizes such return and unless such return occurs within 90 days of receipt. A 15% restocking charge

will be assessed on all such authorized returns. Authorized returns must be freight prepaid and shall include an

authorization number noted on the outside of the package. Such authorization number will be provided by HME at

the time it authorizes such return. All freight sent collect and packages without an authorization number will be

refused and returned to sender.

* Exceptions: The BAT40 and BAT850 Batteries and the HS14, HS14D and HS20-3 Headsets are

warranted for one year. The HS4-3 Earpiece is warranted for 90 days.

The DX100 provides private, secure communication. Each base station can have up to fifteen Beltpacs

“registered” to it. Four of the fifteen Beltpacs can transmit at the same time. Beltpacs can be used either in the

push-to-talk or hands-free mode. The base station operator can stop any Beltpac from transmitting.

The base station can be operated using standard AC electricity, an external DC power source or six AA

batteries. A power supply, cable and a battery sled are included with the base station.

This is an example of a typical theatrical application. A variety of other uses for the DX100 are possible.

SECTION 1. INTRODUCTION

AC40A Battery Charger

EQUIPMENT IDENTIFICATION

The following equipment is standard with the DX100 Wireless Intercom System.

As you unpack the equipment, check the packing list to be sure you received all items listed.

Base Station Antennas

(2 per Base Station)

115/230 Volt AC Power Supply

(1 per Base Station, with Power Cables)

(1 per AC40A Battery Charger, with Power Cables)

BP200 Belt

OPTIONAL EQUIPMENT

HS4-3 Single Earpiece & Lapel Microphone

HS14 Single-Muff Medium-Weight Headset

HS14D Dual-Muff Medium-Weight Headset

HS12 Single-Earpiece Lightweight Headset

HS20-3 Dual-Earpiece Lightweight Headset

AC850 Battery Charger

BAT850 Battery

XLR Headset Adapters:

MD-XLR4M Mini-DIN to 4-Pin Male

MD-XLR4F Mini-DIN to 4-Pin Female

MD-XLR5F Mini-DIN to 5-Pin Female

BS100 Base Station

Beltpac Battery

Belt

ac Pouch

Base Station Batter

Sled

MAIN EQUIPMENT FEATURES

Base Station Features

1. POWER indicator light

2. RECEIVE indicator light

3. RESET button

4. REGISTRATION STATUS display

5. Power “PWR” button

6. Registration “REG” button

7. UN-LATCH button

8. Clear Registration “CLR REG” button

9. Antennas

10. Power connector

11. Battery compartment cover

12. Battery compartment cover release latches

Beltpac Features

1. Headset cable connector

2. Beltpac indicator lights

3. ISO (Isolate) button

4. IC (Intercom) button

5. PWR (Power) button

6. Volume-up button

7. Volume-down button

8. Battery

9. Battery release latch

1 2 3 4 5 6 7 8

8 9

2 3 4 2

Charged batteries

in storage ports

Battery in

charging port

Empty

charging ports

BELTPAC BATTERY CHARGER SETUP

IMPORTANT! – Before installing the system, connect the AC power supply to the AC40A Battery Charger

and plug it into an electrical outlet. Charge all the Beltpac batteries while the other equipment is being

installed. Charging time is about 2.5 hours.

Connect AC Power Supply

• Attach the AC power supply cable connector to the screw connector on the battery charger.

• Plug the power cable connector into the AC power supply.

• Plug the power cable into an electrical outlet.

The red lights on the charger will come on and go off, and then the yellow lights will come on and stay on.

Charge Batteries

Up to four batteries can be charged in the battery

charger at the same time. The battery status lights

next to each charging port are explained below.

Up to six fully charged batteries can be stored in the

battery storage ports.

• Insert a battery in each of four charging ports

until it clicks in place.

• A yellow light next to each charging port stays on

while the port is empty. When a battery is in a

charging port, a flashing yellow light next to it

indicates CHARGE PENDING, which means the

battery is too hot. Adjust the room temperature or

move the charger to a cooler area. When a battery is

in a charging port, a yellow light on steady next to it

means CHARGE FAILED. If this happens, follow

the instructions on the side of battery charger.

• A red CHARGING light next to a battery port

stays on while a battery in the port is charging.

A green READY light next to a battery port goes

on when a battery in the port is fully charged.

Store fully charged batteries in storage ports.

NOTE: The storage ports neither charge nor

maintain the batteries. They simply

provide a place to store the charged

batteries until they are needed.

Batteries should not be left in charge ports after being fully charged. If a battery is left in a charge port for more

than three weeks, the yellow indicator may light up. In this case, it does not indicate a faulty battery.

SECTION 2. EQUIPMENT SETUP

Power cable

connector

ower su

Power supply

cable connector

AC40A Batter

Char

To electrical

outlet

Antenna

connectors

BASE STATION SETUP

Locate the two base station antennas and the AC power adapter and power cable received with the base station,

and connect them to the base station as described below.

Equipment Connections

Step 1. Connect the two enclosed

antennas to the antenna

connectors on the top and right

side of the base station, shown to

the right. Position the antennas

at right angles to each other.

The illustration below shows one

possible arrangement. Turn the

sleeve on each of the antenna

connectors clockwise to tighten

the antennas securely in position.

Step 2. Note which of the following applies to you.

• If using the DX100 with AC power ⎯Plug the connector at the end of the AC power supply

cord into the power connector on top of the base station. Turn the sleeve on the cable connector

clockwise to secure it to the base station. Plug the large female connector at one end of the AC

power cord into the power supply. Plug the other end of the AC power cord into an electrical outlet.

Sleeves

Power

connector

POWER

light PWR button

Antenna

AC power supply

Power

cord

Power cable

connector

Sleeve

Having a fully charged (or new) battery in its battery compartment when operating the DX100 with

AC or external DC power can prevent interruption of communication during a power outage, as the

DX100 base will automatically switch to battery power.

• If using the DX100 with battery power ⎯Press in and up on the two battery cover release

latches to lift the cover and open the battery compartment.

Insert six AA batteries into the battery sled, in the positions shown inside the sled, and install the

sled in the battery compartment as shown below. An HME BAT850 Rechargeable Battery may be

used instead.

Close the battery compartment by pressing its cover down until both latches snap in place.

NOTE: Pressing down on the cover next to both of the latches at the same time will assure its

proper closing.

• If using the DX100 with an external DC power source ⎯We recommend that you purchase a

power cord such as the Radio Shack 12VDC, 5A cigarette lighter power adapter, PN 270-1558.

Follow the manufacturer’s instructions to connect the external DC power source to the power

connector on top of the DX100. Any power supply used with the DX100 should be rated at least

12VDC, 500mA.

Battery cover

release latches

(Push latches in

direction of arrows

and flip lid up.)

Battery sled

with batteries

Having a fully charged (or new) battery in its battery compartment when operating the DX100 with

AC or external DC power can prevent interruption of communication during a power outage, as the

DX100 base will automatically switch to battery power.

Tabla de contenidos

Otros manuales de Sistema de intercomunicación de HM Electronics

HM Electronics

HM Electronics PRO850 Manual de usuario

HM Electronics

HM Electronics DX121 Manual de usuario

HM Electronics

HM Electronics IC100 Especificaciones técnicas

HM Electronics

HM Electronics DX200 Manual de usuario

Manuales populares de Sistema de intercomunicación de otras marcas

Bticino

Bticino LINEA 3000 Manual de usuario

MSI

MSI MSI-140 Manual de usuario

golmar

golmar Stadio Plus Manual de usuario

CyberData

CyberData 011211 series Manual

Vidos

Vidos duo M1021 Manual de usuario

Vimar

Vimar ELVOX 7539/E Manual de usuario

SSS Siedle

SSS Siedle BTSV 850-03 Manual de usuario

Dahua

Dahua VTO Series Manual de usuario

Elvox

Elvox 5651 Manual de usuario

Videx

Videx VIDEOKIT Series Manual de usuario

Rocom

Rocom Doortello Business FW T2.05W2.04 Manual de usuario

Viking

Viking E-35-EWP Manual de usuario

Safeguard Supply

Safeguard Supply LRA-EX1000 Manual de usuario

SSS Siedle

SSS Siedle BFCV 850 Series Manual de usuario

GRD

GRD MAX V2 Manual de usuario

Alecto

Alecto ADI-250 Manual de usuario

Aiphone

Aiphone IE-8MD Manual de usuario

Perel

Perel EDB4 Manual de usuario