Hitachi CG 25SC Manual de usuario

PRODUCT NAME

Hitachi 250 mm Grass Trimmer

Model CG 25SC

Hitachi 300 mm Grass Trimmer

Model CG 30SC

LIST No.

xxx. 2014

REPAIR GUIDE ----------------------------------------------------------------------------------------------------------------- 1

1. Precautions on disassembly and reassembly -----------------------------------------------------------1

STANDARD REPAIR TIME (UNIT) SCHEDULES ------------------------------------------------------------------ 12

CONTENTS

CG 25SC

LIST Nos.

CG 25SC:

CG 30SC:

May 2015

Overseas Sales Division

Page

-1-

Fig. 2

Fig. 1

WARNING: Before conducting repair, be sure to turn off the power switch and disconnect the

power cord plug from the power source outlet.

1. Precautions on disassembly and reassembly

[Bold] and <Bold> numbers in the description below correspond to the item numbers in the parts lists and

exploded assembly diagrams of the Models CG 25SC and CG 30SC, respectively.

CAUTION: Be careful not to cut your finger with the Blade [51] located on the back of the

Protecting Cover [50].

1. Disassembling the housing section

(1) Open the Guide [43] wide and detach it from the housing

as shown in Fig. 1.

(2) Pull up the Upper Cover [49] from the Wire Roll Support [41] while pushing in its two latches together.

Remove the Wire Roll [47] with the nylon wire and Spring (D) [46]. Next, remove the Screws ST4 x 12

[10]. Turn the Protecting Cover [50] in the arrow direction as shown in Fig. 2 to remove it.

[41]

[49]

Latch (2 pcs.)

[47]

[49]

[50]

[10]

[46]

Disassembly of the Model CG 25SC

REPAIR GUIDE

[43]

[50] [10]

[48]

[51]

-2-

Fig. 3

(3) Remove the eight Screws ST4 x 16 [4] from Housing (R) [29] and Housing (L) [35]. Detach the Motor

[39] with the Wire Roll Support [41], Button [32], Lock Pin [33], and Spring (C) [34] as shown in Fig. 3.

(4) Remove the two Screws ST3 x 6 [30] from the Pipe Ass'y [24] to remove the Spacer [31] as shown in

Fig. 3.

2. Removing the motor

(1) Use a hex. bar wrench to turn the Cap [45]

inside the Wire Roll Support [41]. The Cap [45]

comes off together with the M5 Nut [44].

(2) The Wire Roll Support [41] is press-fitted to the

Motor [39]. Use a large bearing puller to remove

it. For easy removal of the support, use the two

side holes of the Wire Roll Support [41] and the

end of the Motor [39] shaft. The Wire Roll

Support [41] is in contact with the ball bearing

of the Motor [39] as shown in Fig. 4.

[4]

[32] [33] [34] [10] [11]

[38]

[39]

[29]

Fig. 4

[39]

[41]

[44]

[45]

[35]

[30]

[24]

[31]

[40]

-3-

Fig. 6

3. Disassembling the handle section

(1) First, remove the Hanger Ass'y [16] and then

use a flat-blade screwdriver to pry off the

Handle Ring [25].

NOTE: Apply a piece of cloth to the flat

end of the screwdriver to protect

parts.

(2) Remove the six Screws ST4 x 16 [4] from Handle (R) [5] and Handle (L) [13]. Remove the Trigger [8],

Spring (A) [9], Spring (B) [14], and the Lock Off Button [12] as shown in Fig. 6.

(3) Remove the two Screws ST4 x 12 [10] from each of the three Cord Clips [11] to remove the Cord [1]

from the body.

Fig. 5

[1]

[2]

[3]

[8] [9] [10] [11]

[12] [13]

[11]

[16]

[15]

[24]

[25]

[10]

[14]

[7]

[6]

[5]

[4]

[25]

Apply a piece

of cloth here.

Flat-blade screwdriver

[16]

-4-

Fig. 8

Reverse the disassembly procedure to reassemble the Model CG 25SC. However, pay particular attention

to the following.

1. Notices on reassembly

(1) Press-fit the Wire Roll Support [41] to the Motor [39] until the

Wire Roll Support [41] contacts the ball bearing of the Motor

[39].

NOTE: Do not press-fit with excessive force. Otherwise,

the Wire Roll Support [41] may be broken.

After press-fitting, put the Cap [45] on the M5 Nut [44] and

tighten it to the shaft of the Motor [39].

NOTE: Do not press-fit with excessive force. Otherwise,

the Cap [45] may fall off.

NOTE: The wire roll support of the Model CG 25SC is

similar to that of the Model CG 30SC but they are

not interchangeable (13.5-mm portion is slightly

different in shape.) Do not mismount.

NOTE: Replace the Wire Roll Support [41] with new one

without fail when replacing the Motor [39].

(2) Mount the Lock Off Button [12] and Spring (B) [14] into Handle (L) [13], and then put Handle (L) [13]

and Handle (R) [5] together aligning the position of Spring (B) [14].

NOTE: When putting Handle (R) [5] and Handle (L) [13] together, completely fit the internal

wires into the grooves of the handle ribs so that the internal wires are not pinched by

the handle bodies.

NOTE: The position of the Lock Off Button [12] is predetermined. Fit the protrusion of the Lock

Off Button [12] in the recessed portion of Handle (L) [13].

[13]

[12] [14]

Fig. 7

[39]

[41]

[44]

[45]

13.5 mm

[11]

[10]

[2]

[1]

[3]

[8]

[9]

[15]

[24]

[10]

[11]

Reassembly of the Model CG 25SC

[7]

-5-

2. Checking after reassembly

(1) Check that the Lock Off Button [12] can be operated normally. Check that the trimmer does not

operate just by pulling the Trigger [8].

(2) Push the Button [32] and check that Housing (R) [29] and Housing (L) [35] can be turned 180° and

locked correctly.

(3) Check the handle portion (Pipe Ass'y [24]) can be smoothly extended and retracted, and firmly locked.

-6-

Fig. 10

Fig. 9

CAUTION: Be careful not to cut your finger with the Blade <46> located on the back of the

Protecting Cover <45>.

1. Disassembling the housing section

(1) Open the Guide <44> wide and detach it from the housing

as shown in Fig. 9.

(2) Pull up the Upper Cover <55> from the Wire Roll Support <49> while pushing in its two latches

together. Remove the Wire Roll <50> with the nylon wire and Spring (D) <54>. Next, remove the four

Screws ST4 x 12 <11>. Turn the Protecting Cover <45> in the arrow direction as shown in Fig. 10 to

remove it.

<49>

<55>

<11>

<54>

<50>

<49>

<55>

<45>

<11>

<45>

<44>

Disassembly of the Model CG 30SC

Latch (2 pcs.)

<46>

-7-

Fig. 11

(3) Remove the eight Screws ST4 x 16 <1> from Housing (R) <43> and Housing (L) <41>. Detach the

Motor <37> with the Wire Roll Support <49>, Button <34>, Lock Pin <35>, and Spring (C) <36> as

shown in Fig. 11.

(4) Remove the two Screws ST3 x 6 <32> from the Pipe Ass'y <22> to remove the Spacer <31> as shown

in Fig. 11.

2. Removing the motor

(1) Use a hex. bar wrench to turn the Cap <53>

inside the Wire Roll Support <49>. The Cap

<53> comes off together with the M5 Nut <52>.

(2) The Wire Roll Support <49> is press-fitted to the

Motor <37>. Use a large bearing puller to

remove it. For easy removal of the support, use

the two side holes of the Wire Roll Support

<49> and the end of the Motor <37> shaft. The

Wire Roll Support <49> is in contact with the

ball bearing of the Motor <37> as shown in Fig.

12.

Fig. 12

<35>

<38>

<1>

<43>

<37>

<34>

<36>

<39>

<11>

<12>

<32>

<31>

<22>

<41>

<37>

<38>

<49>

<52>

<53>

-8-

Fig. 13

3. Disassembling the handle section

(1) Remove the eight Screws ST4 x 16 <1> from Handle (R) <2> and Handle (L) <13>. Remove the

Trigger <6>, Spring (A) <5>, Spring (B) <3>, and the Lock Off Button <4> as shown in Fig. 13.

(2) Remove the two Screws ST4 x 12 <11> from each of the two Cord Clips <12> to remove the Cord

<15> from the body.

<1>

<2>

<3>

<8>

<19>

<16>

<6>

<4> <5>

<22>

<9> <10>

<17> <18>

<20>

<23>

<11> <12>

<13>

<14>

<15>

-9-

Fig. 15

Reverse the disassembly procedure to reassemble the Model CG 30SC. However, pay particular attention

to the following.

1. Notices on reassembly

(1) Press-fit the Wire Roll Support <49> to the Motor <37> until

the Wire Roll Support <49> contacts the ball bearing of the

Motor <37>.

NOTE: Do not press-fit with excessive force. Otherwise,

the Wire Roll Support <49> may be broken.

After press-fitting, put the Cap <53> on the M5 Nut <52> and

tighten it to the shaft of the Motor <37>.

NOTE: Do not press-fit with excessive force. Otherwise,

the Cap <53> may fall off.

NOTE: The wire roll support of the Model CG 30SC is

similar to that of the Model CG 25SC but they are

not interchangeable (5-mm portion is slightly

different in shape.) Do not mismount.

NOTE: Replace the Wire Roll Support <49> with new one

without fail when replacing the Motor <37>.

(2) Mount the Lock Off Button <4> and Spring (B) <3> into Handle (L) <13>, and then put Handle (L) <13>

and Handle (R) <2> together aligning the position of Spring (B) <3>.

NOTE: When putting Handle (R) <2> and Handle (L) <13> together, completely fit the internal

wires into the grooves of the handle ribs so that the internal wires are not pinched by

the handle bodies.

NOTE: The position of the Lock Off Button <4> is predetermined. Fit the protrusion of the Lock

Off Button <4> in the recessed portion of Handle (L) <13>.

Fig. 14 <37>

<38>

<49>

<52>

<53>

5 mm

Reassembly of the Model CG 30SC

<13>

<4>

<3>

<5>

<6>

<16>

<15>

<14>

<12>

<11>

<7> <22>

<20>

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Recortadora de Hitachi

Hitachi

Hitachi CG 40EAS (P) Manual de usuario

Hitachi

Hitachi CG 36DL(L) Guía de solución de problemas

Hitachi

Hitachi CG 14DSDL Manual de usuario

Hitachi

Hitachi CH27EPAP Manual de usuario

Hitachi

Hitachi CG25EJ (L) Manual de usuario

Hitachi

Hitachi CH 36DL Manual de usuario

Hitachi

Hitachi CH 62EA3 (ST) Manual de usuario

Hitachi

Hitachi CH50EA (ST) Manual de usuario

Hitachi

Hitachi CG40EK Manual de usuario

Hitachi

Hitachi CH 36DL Guía de solución de problemas

Hitachi

Hitachi CH 22EAP2 Manual de usuario

Hitachi

Hitachi CG 27EBDP Manual de usuario

Hitachi

Hitachi CH 14DSL Manual de usuario

Hitachi

Hitachi CG 30SC Manual de usuario

Hitachi

Hitachi FCH 48Y Manual de usuario

Hitachi

Hitachi CG 24EVSP Manual de usuario

Hitachi

Hitachi CG 25EUAP Manual de usuario

Hitachi

Hitachi CG47EJ Manual de usuario

Hitachi

Hitachi CG22EJ Manual de usuario

Hitachi

Hitachi CG 24EC (S) Manual de usuario

Hitachi

Hitachi CG24EKB (SL) Manual de usuario

Hitachi

Hitachi CG 25EUP2 Manual de usuario

Hitachi

Hitachi CG 28EJ Manual de usuario

Hitachi

Hitachi CH 50EA(ST) Manual de usuario

Manuales populares de Recortadora de otras marcas

MTD

MTD HT 51 E Manual de usuario

McCulloch

McCulloch T22 LS Manual de usuario

COCKRAFT

COCKRAFT PRO HL36-S Manual de usuario

Grizzly

Grizzly CT 1800 Li Manual de usuario

Peco

Peco Z Trimmer ZT-3000 Manual de usuario

Solo

Solo 116 Manual de usuario

Stiga

Stiga ST 1200 Manual de usuario

Echo

Echo GT-225 - 10-09 Manual de usuario

RedMax

RedMax BT17 Manual de usuario

GreenWorks

GreenWorks STA806 Manual de usuario

Parkside

Parkside PHSL 900 A3 Manual de usuario

Gardeo

Gardeo PRO GPTHT2560 Manual de usuario

Park

Park DT-810870 Manual de usuario

Worx

Worx WG209 Manual de usuario

Gardenline

Gardenline 43671/HTKS26 Manual de usuario

Makita

Makita 3710 Manual de usuario

Champion

Champion 100683 Manual de usuario

Stihl

Stihl FS 311 Manual de usuario