Hitachi VSP F370 Guía del usuario
Hitachi Virtual Storage Platform F350, F370,
G350, and G370
88-02-0x
Storage System Installation (without SVP)
This guide provides information and instructions for installing and setting up your Hitachi Virtual Storage
Platform VSP F350, VSP F370, VSP G350, or VSP G370 storage system.
MK-97HM85020-00
July 2018
© 2018 Hitachi, Ltd. All rights reserved.
No part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including copying and
recording, or stored in a database or retrieval system for commercial purposes without the express written permission of Hitachi, Ltd., or
Hitachi Vantara Corporation (collectively “Hitachi”). Licensee may make copies of the Materials provided that any such copy is: (i) created as an
essential step in utilization of the Software as licensed and is used in no other manner; or (ii) used for archival purposes. Licensee may not
make any other copies of the Materials. “Materials” mean text, data, photographs, graphics, audio, video and documents.
Hitachi reserves the right to make changes to this Material at any time without notice and assumes no responsibility for its use. The Materials
contain the most current information available at the time of publication.
Some of the features described in the Materials might not be currently available. Refer to the most recent product announcement for
information about feature and product availability, or contact Hitachi Vantara Corporation at https://support.hitachivantara.com/en_us/contact-
us.html.
Notice: Hitachi products and services can be ordered only under the terms and conditions of the applicable Hitachi agreements. The use of
Hitachi products is governed by the terms of your agreements with Hitachi Vantara Corporation.
By using this software, you agree that you are responsible for:
1. Acquiring the relevant consents as may be required under local privacy laws or otherwise from authorized employees and other
individuals; and
2. Verifying that your data continues to be held, retrieved, deleted, or otherwise processed in accordance with relevant laws.
Notice on Export Controls. The technical data and technology inherent in this Document may be subject to U.S. export control laws, including
the U.S. Export Administration Act and its associated regulations, and may be subject to export or import regulations in other countries. Reader
agrees to comply strictly with all such regulations and acknowledges that Reader has the responsibility to obtain licenses to export, re-export, or
import the Document and any Compliant Products.
Hitachi is a registered trademark of Hitachi, Ltd., in the United States and other countries.
AIX, AS/400e, DB2, Domino, DS6000, DS8000, Enterprise Storage Server, eServer, FICON, FlashCopy, IBM, Lotus, MVS, OS/390, PowerPC, RS/6000,
S/390, System z9, System z10, Tivoli, z/OS, z9, z10, z13, z/VM, and z/VSE are registered trademarks or trademarks of International Business
Machines Corporation.
Active Directory, ActiveX, Bing, Excel, Hyper-V, Internet Explorer, the Internet Explorer logo, Microsoft, the Microsoft Corporate Logo, MS-DOS,
Outlook, PowerPoint, SharePoint, Silverlight, SmartScreen, SQL Server, Visual Basic, Visual C++, Visual Studio, Windows, the Windows logo,
Windows Azure, Windows PowerShell, Windows Server, the Windows start button, and Windows Vista are registered trademarks or trademarks
of Microsoft Corporation. Microsoft product screen shots are reprinted with permission from Microsoft Corporation.
iPad is a trademark of Apple Inc., registered in the U.S. and other countries.
All other trademarks, service marks, and company names in this document or website are properties of their respective owners.
Storage system installation (without SVP) 2
Installing your storage system
Hitachi Virtual Storage Platform G/F350 and G/F370 storage systems are designed for
self-installation, so you can set up your storage system for the rst time without
assistance from a Hitachi Vantara representative.
Step 1: Unpack the storage system
Before you begin
Make sure your data center meets all site preparation requirements before you install
the storage system. In addition, if you are not using a Hitachi Universal V2 rack, make
sure the electrical specications of your rack meet the power requirements of the
storage system.
Procedure
1. Inspect all materials for signs of damage. If you see damage, discontinue the
installation and contact your Hitachi Vantara representative.
2. If your storage system did not arrive factory-installed in a rack, loosen the band
around the cartons and open all boxes. Remove all packing materials, envelopes,
and boxes from the cartons.
3. Retain all packing materials and cartons in case you need to transport or ship the
storage system in the future.
4. Check the items you received against the packing list. If any items are missing or
damaged, discontinue the installation and contact your Hitachi Vantara
representative.
5. Place the keys for the front bezel in a safe place. You will need them to attach the
bezel to the front of the controllers.
6. If your storage system arrived already factory-installed in a rack, skip step 2 and
proceed to step 3 (on page 10) .
Step 2: Install the storage system into a rack
Mount the controller into the Hitachi Universal V2 rack or into a 4-post EIA 310-D
compliant 19-inch rack with square mounting holes and rear-facing power distribution
units (PDUs).
Installing your storage system
Storage system installation (without SVP) 3
Note: Hitachi Vantara provides rail kits (part number A34V-600-850-UNI-S) for
mounting the storage system controller into third-party racks. Mounting rails
are shipped in a separate box. The left rail has the letter L cut into the sheet
metal, as shown in the following gure. The right mounting rail has no similar
marking. The kit includes more screws than are required for securing the rails
to the rack.
The following instructions describe how to install the controller into a Hitachi Universal
V2 rack. For information about installing the controller in a third-party rack, see the
documentation for that rack.
WARNING: Due to the heavy weight of the controller, use a mechanical lift or
at least three people to lift and mount the controller in the rack.
Before you begin
■Make sure you have a 19-inch rack that is secure and cannot fall over.
■Make sure the rack has one or more PDUs installed.
■Verify that all power cables are removed from the AC power receptacles on the rear of
the controller.
■Install the rack stabilizers before mounting the storage system in the rack.
Procedure
1. Loosen the four adjustment screws, if needed, so that the rail halves can be
adjusted freely to t between the front and rear vertical rack posts.
Step 2: Install the storage system into a rack
Installing your storage system
Storage system installation (without SVP) 4
2. Facing the front of the rack, nd an empty 2U location where you will install the
controller.
3. Place the left mounting rail as shown in the following gure, and then use two
athead screws to secure the rails to the front vertical post on the rack.
Note: The athead screws are M5x10 (PZ-2), where PZ-2 refers to the
size and type of the Philips head).
Step 2: Install the storage system into a rack
Installing your storage system
Storage system installation (without SVP) 5
4. Slide the length of the left mounting rail to t the length of the rack.
5. Use two athead screws to secure the rails to the rear vertical post on the rack.
Step 2: Install the storage system into a rack
Installing your storage system
Storage system installation (without SVP) 6
6. Tighten the four screws on the left mounting rail.
Step 2: Install the storage system into a rack
Installing your storage system
Storage system installation (without SVP) 7
7. Repeat steps 1 through 6 to attach and secure the right mounting rail to the right
side of the rack.
8. Position the controller so the front faces the front of the rack, and then slide the
controller gently onto the rails. Stop sliding when the mounting anges on the front
of the controller touch the vertical face of the rack.
9. Find the washers, O-rings, and screws included with the bezel bracket mounting kit
(part number 043-100885-01.P). Then install a washer, O-ring, and screw (one per
side) between the mounting prole of the rack and the mounting "ears" of the
controller. The screw engages the threaded hole in the rail.
Step 2: Install the storage system into a rack
Installing your storage system
Storage system installation (without SVP) 8
Item Description
1 Screw
2 O-ring
3 Washer
The rack installation for your controller should resemble the following gure.
Step 2: Install the storage system into a rack
Installing your storage system
Storage system installation (without SVP) 9
Item Description
1 Washers, O-rings, and screws securing the controller to the front of
the rack
Step 3: Connect the storage system to power
The storage system's input voltage is auto-adjusting for 100-120 (+6%) / 200-240 (-11%)
VAC, 50-60 Hz power connections. Power is provided through two power supplies, one
per controller.
For best practice, establish power redundancy by routing each power supply to
independent PDUs and then routing the PDUs to separate external power sources on
dierent branch circuits. This arrangement enables the storage system to continue
operating if AC power is lost to one power supply.
Note: Multiple outlets in a PDU or power strip do not constitute an
independent electrical source.
Procedure
1. Conrm that all power sources are o.
2. Connect an AC power cable to the power receptacle on the rear of each controller.
3. Route the power cables from each controller to separate PDUs, and then use the
pre-installed tie wraps at each controller power receptacle to secure the power
cables, as shown in the following gure.
Step 3: Connect the storage system to power
Installing your storage system
Storage system installation (without SVP) 10
Este manual sirve para los siguientes modelos
2
Tabla de contenidos
Otros manuales de Almacenamiento de Hitachi
Hitachi
Hitachi LifeStudio Mobile Graphite 320GB Manual de usuario
Hitachi
Hitachi VSP E990 Manual de operación y mantenimiento
Hitachi
Hitachi Virtual Storage Platform G130 Manual de operación y mantenimiento
Hitachi
Hitachi G1000 Instrucciones de instalación
Hitachi
Hitachi ic35l060avv207-0 - Deskstar 60 GB Hard Drive Manual de usuario
Hitachi
Hitachi HUS VM Manual de instalación
Hitachi
Hitachi E990 Manual de usuario
Hitachi
Hitachi Ultrastar 15K73 Manual de usuario
Hitachi
Hitachi IC25N040ATCS04-0 - Travelstar 40GN 40GB UDMA/100 4200RPM 2MB 2.5" IDE Hard... Manual de usuario
Hitachi
Hitachi E590 Manual de usuario
Hitachi
Hitachi Travelstar 7K100 Manual de usuario
Hitachi
Hitachi IC25N040ATMR04-0 - Travelstar 40GB Laptop Hard Drive 9.5mm 2.5 Inch Notebook... Manual de usuario
Hitachi
Hitachi 3.5-inch Deskstar HDS721010DLE630 Manual de usuario
Hitachi
Hitachi X Mobile 250GB Manual de usuario
Hitachi
Hitachi HUS156060VLS600 Manual de usuario
Hitachi
Hitachi Deskstar 7K400 Manual de usuario
Hitachi
Hitachi DKC910I Manual de usuario
Hitachi
Hitachi Virtual Storage Platform F400 Manual de operación y mantenimiento
Hitachi
Hitachi Adaptable Modular Storage 2000 Instrucciones de uso
Hitachi
Hitachi Travelstar 2.5 inch SATA HTS722020K9A300 Manual de usuario
Manuales populares de Almacenamiento de otras marcas
Spectra Logic
Spectra Logic T-Series Spectra T50e Manual de usuario
Panasonic
Panasonic LKM-F931-1 Manual de usuario
Tabernus
Tabernus Enterprise Erase E2400 Manual de usuario
Rocstor
Rocstor COMMANDER 3F series Manual de usuario
HP
HP P9000 Manual de usuario
Western Digital
Western Digital Ultrastar Data60 Manual de usuario