Hitachi CB 18DBL Manual de usuario

Overseas Sales Division

PRODUCT NAME

Hitachi 18 V Cordless Band Saw

Model CB 18DBL C

LIST No.

CB 18DBL: K803

Jul. 2015

CONTENTS

REPAIR GUIDE ----------------------------------------------------------------------------------------------------------------1

1. Precautions on disassembly and reassembly ------------------------------------------------------------1

2. Precautions on disassembly and reassembly of the battery charger -----------------------------13

STANDARD REPAIR TIME (UNIT) SCHEDULES -------------------------------------------------------------------14

Page

-1-

• Removal of the band saw blade

WARNING: Be sure to remove the battery from the main body before starting repair or maintenance

work. If the switch is activated inadvertently with the battery still mounted on the main

body, the motor may turn unexpectedly and could cause serious injury.

1. Precautions on disassembly and reassembly

[Bold] numbers in the description below correspond to the item numbers in the parts list and the exploded

assembly diagrams for the Model CB 18DBL.

First, be sure to remove the saw blade from the main body to prevent damage to the cutting edges of the

saw blade and avoid personal injury due to the saw blade.

1. Removal of the band saw blade

NOTE: Wear leather gloves before handling the band saw blade to protect your hands from injury

caused by sharp cutting edges. Carefully remove the band saw blade from the main body in

a slow manner to avoid personal injury caused by suddenly ejected band saw blade.

(1) Gently turn the Tension Lever [33] to loosen as shown in the figure below.

(2) Loosen the two Bolts M5 x 16 [80] with the Hex. Bar Wrench 4 mm [501].

NOTE: The Bolt M5 x 16 [80] is retained by the O-ring [77].

(3) Push the claws of Blade Pulley Cover (A) [74] and Blade Pulley Cover (B) [73] to open them.

(4) Slowly turn Blade Pulley (A) [72] or Blade Pulley (B) [71] by hand until the Band Saw Blade [66] comes

out from the top edges of the blade pulleys. Then remove the Band Saw Blade [66].

Disassembly

[33]

Loosen

Claws

[74] [73]

[72] [71]

[66]

Top edge of the

blade pulley

The band saw

blade comes out.

REPAIR GUIDE

[501]

[80]

[66]

-2-

• Removal of blade pulleys (A) and (B) and blade pulley rubbers

2. Removal of blade pulley (A) and blade pulley rubber

(1) Loosen the Bolt M6 x 16 [65] and remove the Spring Washer M6 [31], Washer (A) [64] and Blade Pulley

(A) [72] from Pulley Shaft (A) [23].

(2) Remove the Blade Pulley Rubber [70] from Blade Pulley (A) [72].

3. Removal of blade pulley (B) and blade pulley rubber

(1) Loosen the Bolt M6 x 16 [65] and remove the Spring Washer M6 [31], Washer (A) [64] and Blade Pulley

(B) [71] from the Slide Plate [45].

NOTE: Be careful not to lose the Flat Washer [63] that might be attached to the side of the Blade

Pulley (B) [71] when removing Blade Pulley (B) [71].

(2) Remove the Blade Pulley Rubber [70] from Blade Pulley (B) [71].

NOTE: The Needle Bearing [69] is press-fitted in Blade Pulley (B) [71]. Replace the Needle

Bearing [69] with new one if it is damaged.

[65]

[31]

[64]

[72]

[70]

[64]

[31]

[65]

[71]

[70]

[63]

[23]

[45]

[40]

[69]

[28]

-3-

• Disassembly of bearing holder (A) ass'y and bearing holder (B) ass’y

4. Disassembly of bearing holder (A) ass'y

(1) Loosen the Screw D4 x 16 [8] and the Screw D4 x 20 [76]. Remove Cover Holder (A) [79] and Bearing

Holder (A) Ass'y [61] from the Frame [40].

(2) Loosen the two Bearing Pins (B) [55] with a flat-blade screwdriver and remove the two Spring Washers

M6 [54], two Bolt Washers M6 [53], four Ball Bearings 606VV [52] and two Washers M5 [51] from

Bearing Holder (A) [62].

(3) Remove the Bearing Pin [56], two Bolt Washers M4 [57] and Roller 604VV [58] from Bearing Holder (A)

[62].

5. Disassembly of bearing holder (B) ass'y

(1) Loosen the Screw D4 x 16 [8] and Screw D4 x 20 [76]. Remove Cover Holder (B) [75] and Bearing

Holder (B) Ass'y [49] from the Frame [40].

(2) Loosen two Bearing Pins (B) [55] with a flat-blade screwdriver and remove the two Spring Washers M6

[54], two Bolt Washers M6 [53], four Ball Bearings 606VV [52] and two Washers M5 [51] from Bearing

Holder (B) [50].

(3) Remove the Bearing Pin [56], two Bolt Washers M4 [57] and Roller 604VV [58] from Bearing Holder (B)

[50].

[40]

[62]

[61]

[55]

[54]

[53]

[52]

[51]

[49]

[55]

[50]

[54]

[53]

[52]

[51]

[56]

[57]

[58]

[75]

[8]

[76]

[79]

[8]

[76]

[58]

[57]

[56]

-4-

• Disassembly of the handle set and housing set

6. Removal of blade pulley covers (A) and (B)

(1) Remove the two Retaining Rings (E-type) for D3 Shaft [68] with long-nose pliers and pull out the two

Pins D4 [67] from the Frame [40].

(2) Remove Blade Pulley Cover (A) [74] and Blade Pulley Cover (B) [73] from the Frame [40].

(3) Remove the O-rings [77] from Blade Pulley Cover (A) [74] and Blade Pulley Cover (B) [73]. Remove

the Bolt M5 x 16 [80] and Washer M5 [78].

7. Disassembly of the handle set

(1) Loosen and remove the two Screws D4 x 16 [8] at the front of the main body.

(2) Turn the main body upside down. Loosen and remove the eight Screws D4 x 16 [8] and remove the

Handle Set [2] from the Frame [40]. Then disassemble the Handle Set [2].

NOTE: Be careful not to lose the internal parts (especially the Spring [5] attached to the Knob [6])

when disassembling the Handle Set [2].

8. Disassembly of the housing set

(1) After removal of Blade Pulley (A) [72], loosen and remove the three Screws D4 x 16 [8].

(2) Turn the main body upside down. Loosen and remove the four Screws D4 x 20 [29] and remove the

Housing Set [12] from the Frame [40].

(3) Loosen and remove the four Screws D3 x 20 [35]. Then disassemble the Housing Set [12].

[40]

[2]

[3]

[5]

[6]

[12]

[29] [28]

[14]

[35]

[8]

-5-

• Disassembly of the rotor pinion set and gear box ass'y

9. Disassembly of the rotor pinion set and gear box ass'y

(1) After disassembly of the Housing Set [12], remove the Stator FET PCBAss'y [13], Rotor Pinion Set [14]

and the Gear BoxAss'y [28] from the Housing Set [12].

(2) Pull out the Rotor Pinion Set [14] from the Gear Box Ass'y [28] and then pull out the Rotor Pinion Set

[14] from the stator of the Stator FET PCB [13].

(3) Loosen the three Screws D4 x 16 [17] inside the Gear BoxAss'y [28] and remove the Gear Case Cover

[18].

(4) Remove the Lock Washer [19], three gears of Planet Gear (A) Set [20], Pinion (B) [21], three gears of

Planet Gear (A) [20] and Ring Gear [22] from the Gear Case [25].

(5) Remove the Retaining Ring for D15 Shaft [27] from Pulley Shaft (A) [23] by using a retaining ring puller.

(6) Push Pulley Shaft (A) [23] on the retaining ring side to remove it together with the Ball Bearing 6902VV

[24] (on the gear chamber side) and Ring [26] from the Gear Case [25].

(7) Push the Ball Bearing 6902VV [24] (on the retaining ring side) on the gear chamber side of the Gear

Case [25] to remove it.

[12]

[40]

[13]

[14]

[28]

[17]

[18]

[25]

[19]

[20] [21]

[20]

[22]

[27]

[23]

[24]

[26]

-6-

• Disassembly of the stator FET PCB

10. Removal of the stator FET PCB

(1) After disassembly of the Handle Set [2] and Housing Set [12], remove the Stator FET PCB [13], Rotor

Pinion Set [14], and Gear BoxAss'y [28] from the Housing Set [12].

(2) Pull out the Rotor Pinion Set [14] from the Gear Box Ass'y [28] and then pull out the Rotor Pinion Set

[14] from the stator of the Stator FET PCB [13].

(3) Peel silicon rubber off the heads of the two Screws M3.5 x 6 [9] and then loosen and remove them.

Remove the connector between the Stator FET PCB [13] and the Switch [4] to remove the Switch [4].

(4) Pull out the Dial [10] from the volume PCB ass'y of the Stator FET PCB [13].

NOTE: Be careful not to lose the O-ring [11] attached to the Dial [10].

[12]

[2]

[13]

[40]

[14]

[

]

Stator

[9] Connector

[4]

Volume

PCB ass'y

[10]

[11]

-7-

• Removal of the tension lever and slide plate

11. Removal of the tension lever

(1) Loosen the Screw M6 x 16 [30] and remove the Tension Lever [33], Spring Washer M6 [31] and Bolt

Washer M6 [32] from the Lever Shaft [37].

(2) Loosen and remove the four Screws D4 x 16 [8] to remove the Tension Lever Holder [34] from the

Frame [40].

(3) Remove the Ring [36], Lever Shaft [37], Sleeve [38] and Tension Spring [46] from the Frame [40].

NOTE: The Sleeve [38] may be attached to the Lever Shaft [37] with grease.

12. Removal of the slide plate

(1) After removal of Blade Pulley (B) [71], remove the Flat Washer [63] from pulley shaft (B) in the Slide

Plate [45].

NOTE: The Flat Washer [63] may be attached to Blade Pulley (B) [71] with grease.

(2) Loosen and remove the four Screws D4 x 16 [8] together with four Washers (B) [41] from the Frame

[40].

(3) Remove the Slide Plate [45] from the Frame [40].

NOTE: The Lock Nut M5 [48] and Screw M5 x 10 [47] are attached to the Slide Plate [45].

(4) Remove the four Collars [44] and Protection Plate [43] from the Frame [40].

[40]

[71]

[72]

[63]

[45]

[30]

[31]

[32] [33]

[31]

[34]

[36]

[37]

[38]

[46]

[8]

[41]

[43]

[44]

[48]

[47]

-8-

• Silicone application points

Reassembly can be accomplished by following the disassembly procedures in reverse. However, special

attention should be given to the following items.

1. Reassembly of bearing holder (A) ass'y

(1) Coat Threebond 1401B to the threaded portions of two Bearing Pins (B) [55].

(2) Insert a 0.6-mm thickness gauge between the Ball Bearings 606VV [52] and lightly press the Ball

Bearings 606VV [52] each other. Then tighten two Bearing Pins (B) [55].

2. Reassembly of bearing holder (B) ass'y

(1) Coat Threebond 1401B to the threaded portion of two Bearing Pins (B) [55].

(2) Insert a 0.6-mm thickness gauge between the Ball Bearings 606VV [52] and lightly press the Ball

Bearings 606VV [52] each other. Then tighten two Bearing Pins (B) [55].

3. Reassembly of the handle set and the housing set

When reassembling the Handle Set [2] and Housing Set [12], be careful not to catch the internal wires of

the stator ass'y, controller ass'y, LED ass'y, volume ass'y, indicator ass'y, capacitor ass'y, and battery

terminal in the Stator FET PCB [13] between handles (A) and (B) of the Handle Set [2], between housings

(A) and (B) of the Housing Set [12], and the Frame [40].

NOTE: Refer to "5. Reassembly of the power supply unit and stator FET PCB" on the next page.

4. Reassembly of the gear box ass'y

(1) Replace all the six gears of Planet Gear (A) Set [20] with new ones.

(2) Apply Shin-Etsu Silicone KE347B to the points shown in the figure below before mounting the Gear

Case Cover [18] to the Gear Case [25].

(3) After reassembly, check that Pulley Shaft (A) [23] turns smoothly.

Reassembly

Gear case side

[25] [19]

Apply about 0.8 gram of silicone to the edge of the Lock

Washer [19] (entire circumference) to fill the gap with the

Gear Case [25].

NOTE: Apply silicone to the stopper portions of the

Lock Washer [19] so that the concave portions

are completely covered.

Stopper portions of [19]

-9-

• Mounting the stator FET PCB to the housing set

• Mounting the housing set to the frame

5. Reassembly of the power supply unit and stator FET PCB

(1) Mount the Dial [10] to the volume PCB ass'y in the Stator FET PCB [13] according to the following

procedure.

a) Apply 0.5 gram of NPC SEP-3A grease to the circumference of the O-ring [11] and fit the O-ring [11]

to the Dial [10].

b) Insert the Dial [10] a little into the volume PCB ass'y in the Stator FET PCB [13] and turn it

counterclockwise until it stops.

c) Pull out the Dial [10] from the volume PCB ass'y. Align the mark “1” on the Dial [10] with the

protrusion on the cover of the volume PCB ass'y and then fully insert the Dial [10] into the volume

PCB ass'y.

d) Fully turn the Dial [10] clockwise. Check that the mark “A” on the Dial [10] aligns with the protrusion

on the cover.

e) If not aligned, repeat the above steps b) to d).

(2) Fit the flange portion of the stator in the Stator FET PCB [13] in the concave portion of housing (A) of the

Housing Set [12] when mounting the Stator FET PCB [13] to housing (A). Fit the two 16AWG internal

wires (red and black) and sixteen 28AWG internal wires (white and black) of the Stator FET PCB [13]

into the groove of housing (A) of the Housing Set [12] as shown in the figure below.

(3) When mounting the Housing Set [12] to the Frame [40], tighten the three Screws D4 x 16 [8] on the

Frame [40] side first and then tighten the four Screws D4 x 20 [29] on the Housing Set [12] side.

[28]

[13]

[14]

Housing (A) of [12]

Flange portion of the stator

Fit the internal wires into this groove.

[40] [28] [8]

Align the hole of the Gear Box Ass'y [28]

with the hole of the Frame [40].

Otros manuales para CB 18DBL

Tabla de contenidos

Otros manuales de Sierra de Hitachi

Hitachi

Hitachi C 12YA Manual de usuario

Hitachi

Hitachi CR 13V2 Manual de usuario

Hitachi

Hitachi C 8FC Manual de usuario

Hitachi

Hitachi CD 7 Manual de usuario

Hitachi

Hitachi C 7SB3 Guía de solución de problemas

Hitachi

Hitachi C 10FCH2 Manual de usuario

Hitachi

Hitachi CC14SF - Power Tools 14'' Heavy-Duty Cut-Off... Manual de usuario

Hitachi

Hitachi CR 13V2 Manual

Hitachi

Hitachi CR 13VA Manual de usuario

Hitachi

Hitachi C 12LDH Manual

Hitachi

Hitachi CD 12F Manual de usuario

Hitachi

Hitachi C8FSE - 8-1/2" Sliding Compound Miter Saw Manual de usuario

Hitachi

Hitachi C 9SA2 Manual de usuario

Hitachi

Hitachi FC 6SB Manual de usuario

Hitachi

Hitachi C 18DMR Manual de usuario

Hitachi

Hitachi CR 13VC Manual de usuario

Hitachi

Hitachi CB 18DBL Manual de usuario

Hitachi

Hitachi C 7MFA Manual de usuario

Hitachi

Hitachi C 7BD Manual del operador

Hitachi

Hitachi C 6DC Manual de usuario

Hitachi

Hitachi C 12LDH Manual de usuario

Hitachi

Hitachi C 15FB Manual de usuario

Hitachi

Hitachi CS30EH Manual de usuario

Hitachi

Hitachi CR 13VA Manual

Manuales populares de Sierra de otras marcas

RIDGID

RIDGID BS1400 Manual de usuario

ATIKA

ATIKA BWS 400-2 Manual de usuario

RGC

RGC FS20 Manual de usuario

Makita

Makita M2300 Manual de usuario

IMET Spa

IMET Spa BASIC 300 PLUS SHI Manual de usuario

IMET Spa

IMET Spa SIRIO 370 AF-E Manual de usuario

Optimum

Optimum OPTisaw CS 275 Manual de usuario

Makita

Makita BPB180 Manual de usuario

Stihl

Stihl MS 462 C-M Manual de usuario

AEG

AEG TS 250 K Manual de usuario

Meec tools

Meec tools 004665 Manual de usuario

Makita

Makita LS1018L Manual de usuario

Ryobi

Ryobi RCS1400 Manual de usuario

DeWalt

DeWalt DCS391 Manual de usuario

Sealey

Sealey SA72 Manual de usuario

skilsaw

skilsaw SPT88 Instrucciones de montaje

Urrea

Urrea SI810 Dimensiones y guía de instalación

EINHELL

EINHELL BKG 210/1 Manual de usuario