Hitachi RAM-70NP4B Manual de usuario
RAM-70NP4B
NO. 0585E
SPECIFICATIONS AND PARTS ARE SUBJECT TO CHANGE FOR IMPROVEMENT
ROOM AIR CONDITIONER
OUTDOOR UNIT
JANUARY 2015
Refrigeration & Air-Conditioning Division
SERVICE MANUAL
PM
REFER TO THE FOUNDATION MANUAL
TECHNICAL INFORMATION
FOR SERVICE PERSONNEL ONLY
CONTENTS
SPECIFICATIONS---------------------------------------------------------------------5
FEATURES---------------------------------------------------------------------------- 11
INSTALLATION----------------------------------------------------------------------- 15
CONSTRUCTION AND DIMENSIONAL DIAGRAM ----------------------- 19
MAIN PARTS COMPONENT ---------------------------------------------------- 20
WIRING DIAGRAM ----------------------------------------------------------------- 23
CIRCUIT DIAGRAM ---------------------------------------------------------------- 25
BLOCK DIAGRAM ------------------------------------------------------------------ 27
BASIC MODE ------------------------------------------------------------------------ 33
REFRIGERATING CYCLE DIAGRAM----------------------------------------- 53
DESCRIPTION OF MAIN CIRCUIT OPERATION------------------------- 54
TROUBLE SHOOTING ------------------------------------------------------------ 68
PARTS LIST AND DIAGRAM---------------------------------------------------- 86
After installation
850
800
298
58
(W)
(A)
COOLING CAPACITY
DC INVERTER QUADRUPLE SYSTEM MULTI
TYPE
MODEL
POWER SOURCE
TOTAL INPUT
TOTAL AMPERES
SPECIFICATIONS
OUTDOOR UNIT
RAM-70NP4B
HEATING CAPACITY
DIMENSIONS (mm)
NET WEIGHT
1ø, 220 - 240V, 50/60Hz
W
H
D
(kg)
(kW)
(B.T.U.)
REFER TO THE SPECIFICATIONS PAGE
RAM-70NP4B
– 1 –
SAFETY DURING REPAIR WORK
1. In order to disassemble and repair
the unit in question, be sure to
disconnect the power cord plug
from the power outlet before starting
the work.
2. If it is necessary to replace any parts, they should be replaced with respective genuine parts for the unit,
and the replacement must be effected in correct manner according to the instructions in the Service Manual
of the unit.
If the contacts of electrical
parts are defective, replace the
electrical parts without trying to
repair them.
3. After completion of repairs, the initial state
should be restored.
4. Lead wires should be connected and laid as
in the initial state.
5. Modification of the unit by the user himself
should absolutely be prohibited.
6. Tools and measuring instruments for use in repairs or inspection should be accurately calibrated in advance.
7. In installing the unit having been repaired, be careful to prevent the occurence of any accident such as
electrical shock, leak of current, or bodily injury due to the drop of any part.
8. To check the insulation of the unit, measure the insulation resistance between the power cord plug and
grounding terminal of the unit. The insulation resistance should be 1M or more as measured by a 500V
DC megger.
9. The initial location of installation such as window, floor or the other should be checked for being and safe
enough to support the repaired unit again.
If it is found not so strong and safe, the unit should be installed at the initial location after reinforced or at
a new location.
10. Any inflammable object must not
be placed about the location of
installation.
11. Check the grounding to see whether
it is proper or not, and if it is found
improper, connect the grounding
terminal to the earth.
– 2 –
WORKING STANDARDS FOR PREVENTING BREAKAGE OF SEMICONDUCTORS
1. Scope
The standards provide for items to be generally observed in carrying and handling semiconductors in relative
manufacturers during maintenance and handling thereof. (They apply the same to handling of abnormal
goods such as rejected goods being returned).
2. Object parts
(1) Micro computer
(2) Integrated circuits (I.C.)
(3) Field-effective transistor (F.E.T.)
(4) P.C. boards or the like to which the parts mentioned in (1) and (2) of this paragraph are equipped.
3. Items to be observed in handling
(1) Use a conductive container for carrying and storing of parts. (Even rejected goods should be handled
in the same way).
Fig. 1. Conductive container
(2) When any part is handled uncovered (in counting, packing and the like), the handling person must always
use himself as a body earth. (Make yourself a body earth by passing 1M earth resistance through a
ring or bracelet).
(3) Be careful not to touch the parts with your clothing when you hold a part even if a body earth is being
taken.
(4) Be sure to place a part on a metal plate with grounding.
(5) Be careful not to fail to turn off power when you repair the printed circuit board. At the same time, try
to repair the printed circuit board on a grounded metal plate.
1M
Fig. 2. Body Earth
Body earth
(Elimik conductive band)
Clip for connection with a
grounding wire
IC
A conductive polyvinyl bag IC
Conductive sponge
– 3 –
(6) Use a three wire type soldering iron including a grounding wire.
Bare copper wire (for body earth)
Working table
Resistor 1 M (1/2W)
Earth wire
Fig. 3. Grounding of the working table
2
Screw stop at the screwed
part using a rag plate
Soldering iron
Grounding wire
Fig. 4. Grounding a solder iron
Use a high insulation mode (100V, 10M or higher) when ordinary iron is to be used.
(7) In checking circuits for maintenance, inspection or some others, be careful not to have the test probes of
the measuring instrument short circuit a load circuit or the like.
Metal plate (of aluminium, stainless steel, etc.)
Staple
– 4 –
1. In quiet or stop operation, slight flowing noise of refrigerant in the refrigerating cycle is heard occasionally,
but this noise is not abnormal for the operation.
2. When it thunders nearby, it is recommend to stop the operation and to disconnect the power cord plug
from the power outlet for safety.
3. In the event of power failure, the air conditioner will restart automatically in the previously selected mode
once the power is restored. In the event of power failure during TIMER operation, the air conditioner will
not start automatically. Re-press ON/OFF button after 3 minutes from when the unit off or power recovery.
4. If the room air conditioner is stopped by adjusting thermostat, or miss operation, and re-start in a moment,
there is occasion that the cooling and heating operation does not start for 3 minutes, it is not abnormal
and this is the result of the operation of IC delay circuit. This IC delay circuit ensures that there is no
danger of blowing fuse or damaging parts even if operation is restarted accidentally.
5. This room air conditioner should not be used at the cooling operation when the outside temperature is
below –10°C (14°F).
6. This room air conditioner (the reverse cycle) should not be used when the outside temperature is below
–15°C (5°F).
If the reverse cycle is used under this condition, the outside heat exchanger is frosted and efficiency falls.
7. When the outside heat exchanger is frosted, the frost is melted by operating the hot gas system, it is not
trouble that at this time fan stops and the vapour may rise from the outside heat exchanger.
!
CAUTION
– 5 –
SPECIFICATIONS
MODEL
FAN MOTOR
FAN MOTOR CAPACITOR
FAN MOTOR PROTECTOR
COMPRESSOR
COMPRESSOR MOTOR CAPACITOR
OVERLOAD PROTECTOR
OVERHEAT PROTECTOR
FUSE (for MICROPROCESSOR)
POWER RELAY
POWER SWITCH
TEMPORARY SWITCH
SERVICE SWITCH
TRANSFORMER
VARISTOR
NOISE SUPPRESSOR
THERMOSTAT
REMOTE CONTROL SWITCH (LIQUID CRYSTAL)
47 W
NO
NO
JU151XC1
NO
YES
YES
5.0A
G4A
NO
NO
YES
NO
450NR
YES
YES(IC)
NO
2300gUNIT
REFRIGERANT CHARGING
VOLUME
(Refrigerant R410A)
WITHOUT REFRIGERANT BECAUSE
COUPLING IS FLARE TYPE.
PIPES (MAX.)
In case the pipe length is more than 30m, add refrigerant R410 at 20gram per every meter exceeds.
RAM-70NP4B
MAX. 60m
– 6 –
SPECIFICATIONS FOR INDOOR UNITS COMBINATION
OPERATION SCOPE
TYPE
DC INVERTER QUADRUPLE SYSTEM MULTI COOLING AND HEATING
MODEL OUTDOOR UNIT
PHASE/VOLTAGE/FREQUENCY
CIRCUIT AMPERES TO CONNECT (A)
COOLING
(FOUR UNITS)
CAPACITY (kW)
(B.T.U./h)
TOTAL INPUT (W)
EER (B.T.U./hW)
TOTAL AMPERES (A)
POWER FACTOR (%)
HEATING
(FOUR UNITS)
CAPACITY (kW)
(B.T.U./h)
TOTAL INPUT (W)
EER (B.T.U./hW)
TOTAL AMPERES (A)
POWER FACTOR (%)
MAXIMUM LENGTH OF PIPING
STANDARD
RAM-70NP4B
1ø, 220 - 240V, 50/60Hz
20A
7.00
23,900
2,110
11.32
9.7 - 8.9
99
8.50
29,010
2,110
13.74
9.70 - 8.90
99
MAX. 60m (FOUR UNIT TOTAL)
CE (EMC&LVD)
RAM-70NP4B
MODEL
W
PACKING
(mm)
H
D
cu.ft.
1,008
848
394
11.89
63
GROSS WEIGHT (kg)
(6.35DX4)/(9.52DX3)/(12.70X1)
FLARE NUT SIZE (SMALL/LARGE)
INDOOR SUCTION
TEMPERATURE (˚C)
COOLING OPERATION SCOPE
OUTDOOR SUCTION
TEMPERATURE (˚C)
INDOOR SUCTION
HUMIDITY (%)
HEATING OPERATION SCOPE
16 ~ 32 –10 ~ 43 BELOW 80
BELOW 27 –15 ~ 21 —
– 7 –
4 ROOM MULTI-SPLIT INVERTER TYPE RAC: RAM-70NP4B
POSSIBLE COMBINATION TO OPERATE (SAME TIME OPERATION)
– 8 –
– 9 –
QUADRUPLE SYSTEM MULTI R.A.C. RAM-70NP4B
INDOOR UNITS COMBINATIONS TO BE ABLE TO INSTALL
Two, three or four indoor units can be installed with one outdoor unit.
And total nominal cooling capacity should not be more than 11.0kW
Be sure to connect two, three or four indoor units to this outdoor unit. If not, condensed water may drop,
resulting in trouble.
Tabla de contenidos
Otros manuales de Acondicionador de aire de Hitachi
Hitachi
Hitachi RAS-80YHA Manual de usuario
Hitachi
Hitachi RAF-35NX2 Manual de usuario
Hitachi
Hitachi RPC-1.5FSR Manual de usuario
Hitachi
Hitachi RAS-(3-6)HVRNM2E Manual de usuario
Hitachi
Hitachi RPI-16.0FSN3PE Manual de usuario
Hitachi
Hitachi RPC-(1.5-6.0)FSN3 Manual de usuario
Hitachi
Hitachi Summit RAC-80YH5 Manual de usuario
Hitachi
Hitachi RAS-S33H2A Manual de usuario
Hitachi
Hitachi RPIH-4.0FSRE Manual de usuario
Hitachi
Hitachi RAD-50PPA Manual de usuario
Hitachi
Hitachi RPIZ-0.8HNDTS1Q Manual de instrucciones
Hitachi
Hitachi RAS-10JH4 Manual de usuario
Hitachi
Hitachi RAS-S10CYK Manual de usuario
Hitachi
Hitachi RAS-18EX9G Manual de usuario
Hitachi
Hitachi RAK-DJ25PHAT Manual de usuario
Hitachi
Hitachi RAC-25FXB Manual de usuario
Hitachi
Hitachi RAS-E60YHAB Manual de usuario
Hitachi
Hitachi RAS-18YH4 Manual de usuario
Hitachi
Hitachi airHome 300 CJ Series Manual de usuario
Hitachi
Hitachi airHome 400 Manual de usuario
