HIS HIS-ML12 E Series Manual de usuario

12" PANEL MOUNT INDUSTRIAL MONITOR
USER MANUAL
Model No. HIS-ML12- _ _ _ E
REVISION E

2 ML12E User Manual, 99151B, September 2021
Table of Contents
Safety and Regulatory Information��������������������������������������������������������������������������������3
FCC Notice �����������������������������������������������������������������������������������������������������������������������������3
Hazardous Locations ��������������������������������������������������������������������������������������������������������������4
Waste Electrical and Electronic Equipment Directive (WEEE) ����������������������������������������������� 4
Mechanical Drawings������������������������������������������������������������������������������������������������������5
Front and Side Views��������������������������������������������������������������������������������������������������������������5
Bottom View����������������������������������������������������������������������������������������������������������������������������5
Rear View �������������������������������������������������������������������������������������������������������������������������������6
Installation Instructions��������������������������������������������������������������������������������������������������7
Step 1: Prepare for Installation ���������������������������������������������������������������������������������������������� 7
Step 2: Bench-test Conguration������������������������������������������������������������������������������������������� 8
Install Cable Connections ������������������������������������������������������������������������������������������������������������������ 8
Install Touch Screen Driver �������������������������������������������������������������������������������������������������������������� 10
Step 3: Install into Panel ������������������������������������������������������������������������������������������������������ 12
Video Settings����������������������������������������������������������������������������������������������������������������14
Setting the Timing Mode ������������������������������������������������������������������������������������������������������� 14
Control Panel Buttons����������������������������������������������������������������������������������������������������������� 15
On-Screen Display (OSD) Menus����������������������������������������������������������������������������������������� 17
Picture Menu������������������������������������������������������������������������������������������������������������������������������������ 17
VGA Settings Menu�������������������������������������������������������������������������������������������������������������������������� 19
Setup Menu�������������������������������������������������������������������������������������������������������������������������������������� 20
Cleaning Instructions����������������������������������������������������������������������������������������������������23
Troubleshooting ������������������������������������������������������������������������������������������������������������24
Video Troubleshooting ���������������������������������������������������������������������������������������������������������� 24
Touch Screen Troubleshooting ��������������������������������������������������������������������������������������������� 26
Specications ����������������������������������������������������������������������������������������������������������������27
Display ����������������������������������������������������������������������������������������������������������������������������������27
Physical ��������������������������������������������������������������������������������������������������������������������������������27
Video�������������������������������������������������������������������������������������������������������������������������������������28
Functional �����������������������������������������������������������������������������������������������������������������������������28
Environmental����������������������������������������������������������������������������������������������������������������������� 29
Electrical �������������������������������������������������������������������������������������������������������������������������������29
Compliances and Certications �������������������������������������������������������������������������������������������� 30
Warranty Statement�������������������������������������������������������������������������������������������������������31

Safety and Regulatory Information
ML12E User Manual, 99151B, September 2021 3
Safety and Regulatory Information
To prevent re or shock hazard, do not expose live components to rain or moisture.
Dangerously high voltages are present inside the unit� Do not disassemble the
unit. Refer servicing to qualied personnel only. Operator could be exposed to
dangerously high voltage if AC power is not connected properly� Verify all wiring is
properly connected�
This equipment is not intended for use in critical applications where its failure
to operate would create immediate life threatening circumstances� Applications
including, but not limited to, nuclear reactor control, aerospace navigation systems
and life support systems are not appropriate for this product�
This product is intended to be mounted in a suitable cabinet or other enclosure�
The NEMA 4, 4X, or 12 ratings are applicable only when properly installed in a like
rated enclosure�
DC Supplied Units only: The HISML12 subject unit is to be powered by a Listed
Power Supply suitable for the application with outputs at SELV/LPS or Class 2 levels
rated 9.6-36.6VDC, 2.5 A max. The equipment is not intended to connect directly to
a DC Mains source�
FCC Notice
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated
in a commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction manual,
may cause harmful interference to radio communications� Operation of this equipment
in a residential area is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense. Any changes or modications not
expressly approved by the grantee of this device could void the user’s authority to operate
the device�
WARNING!
!

Safety and Regulatory Information
4 ML12E User Manual, 99151B, September 2021
Waste Electrical and Electronic Equipment Directive (WEEE)
The following information is only for EU-member states:
The mark shown to the right is in compliance with the Waste Electrical and
Electronic Equipment Directive 2002/96/EC (WEEE)�
The mark indicates the requirement NOT to dispose of the equipment as unsorted
municipal waste, but use the return and collection systems according to local law. Users
should contact their supplier and check the terms and conditions of the purchase contract�
When purchased directly from Hope Industrial Systems, you may contact technical support
for disposal arrangements.
Hazardous Locations
This equipment is suitable for use in Class I, Division 2, Groups A, B, C, and D; Class II,
Division 2, Groups F and G; Class III; or non-hazardous locations only�
Device is open-type and is to be installed in an enclosure suitable for the environment that
is only accessible with the use of a tool�
FR: Cet équipement peut être utilisé dans la Classe I, Division 2, Groupes A, B, C et
D: Classe II, Division 2, Groupes F et G; et Classe III, endroits hasardeux ou endroits
non-hasardeux seulement� Cet appareil doit être installé dans un enclos adapté à un
environnement accessible uniquement avec l’aide d’un outil.
WARNING – EXPLOSION HAZARD – Do not disconnect equipment unless power has
been removed or the area is known to be non-hazardous�
WARNING – EXPLOSION HAZARD – Substitution of any components may impair
suitability for Class I, II & III, Division 2 Locations�
Any steps marked with this symbol are required to ensure compliance with Class
I, II, III, Division 2 Hazardous Location requirements�
HAZ
LOC

Mechanical Drawings
ML12E User Manual, 99151B, September 2021 5
Mechanical Drawings
Front and Side Views
Bottom View
7.1 mm
(0.28")
216.1 mm
(8.51")
295.7 mm
(11.64")
338.1 mm
(13.31")
249 mm
(9.8")
188 mm
(7.4")
269.4 mm
(10.61")
338.1 mm
(13.31")
7.1 mm
(0.28")
55.0 mm
(2.16")
(Design to maximum depth
of 63.5 mm to ensure future
compatibility with later revisions
and replacement units.)

Mechanical Drawings
6 ML12E User Manual, 99151B, September 2021
Rear View
MENU SEL
75 mm VESA Mounting Pattern
(M4 screws provided,
16 mm maximum depth
of screw)

Installation Instructions
ML12E User Manual, 99151B, September 2021 7
Installation Instructions
Step 1: Prepare for Installation
IMPORTANT!
Perform the following steps BEFORE installation of the monitor into the panel.
1� Ensure that sucient power is available.
2� Ensure that sucient space is available to allow for proper air ow into and out of the
unit�
3� Ensure that the air temperature around the unit (top and bottom) will not exceed the
rated specications of the unit.
fThe maximum rated temperature for the HIS-ML12 is 50°C (122°F).
fRemember that heat rises – the temperature at the top of the
cabinet will be much hotter than at the bottom if air inside the
enclosure is not actively circulating. Even in a sealed enclosure,
use of a circulation fan can greatly reduce temperature�
fAlso, remember that even though this product is designed to
operate at 50°C, the life span of any electronic device is shortened
when it is consistently operated at high temperatures. Therefore,
it is wise to take steps to keep the temperature of the ambient air
around the unit as low as possible�
4� Ensure that the ambient humidity of the air around the unit does not exceed the
specications of the unit.
fT h e m a x i m u m r a t e d h u m i d i t y f o r t h e H I S - M L 1 2 i s 9 0 %
non-condensing�
!

Installation Instructions
8 ML12E User Manual, 99151B, September 2021
Step 2: Bench-test Conguration
Make sure everything works before installing into the production environment.
TIP!
If using a KVM extender, please refer to the installation instructions included
with the KVM extender module. It is particularly important to bench-test the full
conguration prior to nal installation. This will help to identify and troubleshoot
any system issues while conguration changes may still be easily made.
Install Cable Connections
All monitors are shipped with a standard VGA video cable� AC-powered displays are also
shipped with a power/mains cable. If you ordered a touch screen monitor, a USB cable is
supplied for the touch screen interface� To use the touch screen Serial (RS-232) interface, a
serial cable may be ordered separately�
The cable ports are located on the rear of the monitor. Refer to the following diagram and
instructions to connect power, video, and touch screen (if applicable) to your monitor�
DVI VIDEO
USB
(for Touch Screen option)
SERIAL
(RS-232)
POWER INPUT
VGA VIDEO

Installation Instructions
ML12E User Manual, 99151B, September 2021 9
Video Connection
The HIS-ML12 supports digital video through its DVI port, and analog video through its VGA port.
After selecting the appropriate interface, connect one end of your video cable to the input port on
the rear of the monitor and secure the screw locks to ensure adequate strain relief� Connect the
other end to the appropriate port on your host computer or other video source�
HAZ
LOC
NOTE: If this step is not performed, the product will not comply with Class I,
II, III, Division 2 Hazardous Location requirements.
TIP!
If the video source has an HDMI or DisplayPort connection, this can be converted
for use with the DVI video port using a simple adapter�
If the video source has a 5 wire analog RGB video output, this can be converted for
use with the VGA video port using a simple adapter�
Certied adapters are available from Hope Industrial Systems. Contact our sales
team for more information�
Power Connection
The HIS-ML12 is available with either AC or DC power input.
AC power input models are powered by 100 to 240 VAC, 0�4/0�2 A, 60/50 Hz� Loosen the
retaining clip for the power cable on the rear of the monitor. Connect the AC power cable to the
power input port on the monitor then retighten the retaining clip. Connect the other end into a
nearby outlet�
HAZ
LOC
NOTE: If this step is not performed, the product will not comply with Class I,
II, III, Division 2 Hazardous Location requirements.

Installation Instructions
10 ML12E User Manual, 99151B, September 2021
DC power input models are powered by 9�6 to 36�6 VDC, 2�5 to 0�65 A, Class 2 or SELV/LPS�
1� With main power disconnected, hook up incoming
power wires to the DC input terminal blocks according
to the label markings. Securely tighten terminal block
screws�
2� Plug the connector into the unit and secure by
tightening the two side screws.
Install Touch Screen Driver
Applies to touch screen monitors only. Instructions below apply to Windows systems. Both USB
and Serial ports are present on all touch screen monitors, but only one should be used to connect
the touch screen interface to the monitor�
Contact Hope Industrial Systems if you require a CD-ROM with documentation and drivers
for touch screens. For a full list of downloadable drivers, please check the following Internet
address:
https://www�HopeIndustrial�com/support/drivers/
IMPORTANT!
If you will be using a USB connection, install the touch screen driver rst, and then
connect the USB cable. If you will be using a Serial connection, connect the Serial
cable rst, and then install the touch screen driver�
USB Connection
1� Select the appropriate driver for your operating system from the web address listed
above�
2� Click to "Run" the software when prompted� Follow on-screen instructions to
download and execute the touch screen driver installation�
3� A cable retention bracket comes installed on the USB port on the rear of the monitor
and will help to secure the cable and ensure adequate strain relief. Without removing
Este manual sirve para los siguientes modelos
6
Tabla de contenidos
Otros manuales de Monitor de HIS

HIS
HIS HIS-ML19- *** G Manual de usuario

HIS
HIS HIS-ML23.8 A Series Manual de usuario

HIS
HIS HIS-ML20- *** B Manual de usuario

HIS
HIS HIS-ML17-xxxB Series Manual de usuario

HIS
HIS HIS-ML15 Manual de usuario

HIS
HIS HIS-UM23.8 Series Manual de usuario

HIS
HIS HIS-UM19-H Series Manual de usuario

HIS
HIS HIS-ML20 C Series Manual de usuario

HIS
HIS HIS-ML17-H Series Manual de usuario

HIS
HIS HIS-UM19.5-***A Manual de usuario























