Hioki 3154 Manual de usuario

Hioki 3154 Manual

Get Pricing & Availability at

ApexWaves.com

Call Today: 1-800-915-6216

Email: sales@apexwaves.com

https://www.apexwaves.com/analyzers/hioki/digital-m-ohm-hitesters/3154

DIGITAL MΩHiTESTER

INSTRUCTION MANUAL

3154

Contents

Introduction i

Inspection ii

Safety Notes iii

Notes on Use vii

Chapter 1 Outline 1

1.1 Product Introduction 1

1.2 Features 1

1.3 Controls and Functions 3

1.3.1 Displays 3

1.3.2 Front Panel 4

1.3.3 Rear Panel 5

Chapter 2 Preparation for Testing 7

2.1 Connecting Power Cord 8

2.2 Powering On and Off the Unit 9

2.3 Connecting Cord and Probes

(9257, 9289, 9294) 10

2.4 Using Handle 11

2.5 Connecting to Equipment to be tested 12

Chapter 3Setting Basic Testing Conditions 13

3.1 Setting Test voltage 14

3.2 Setting and Verifying Comparator 15

3.2.1 Setting Lower Limit Value 15

3.2.2 Setting and Verifying Test mode 17

3.3 Setting and Verifying Resistance Range 18

3.4 Setting and Verifying Timer 19

3.4.1 Setting and Verifying Test Duration 19

3.4.2 Setting and Verifying Delay Time 21

3.4.3 Determining Delay Time 23

3.5 Setting Sampling Rate 25

3.6 Example Test Condition Setting 26

Chapter 4 Testing 29

4.1 Test Flow 30

4.2 Start Testing 31

4.3 During Testing (TEST status) 32

4.4 Measurement Value Display 33

4.5 Completing Testing 34

4.6 Automatic Discharge 35

4.7 Testing with 9299 SWITCHED PROBE 36

4.7.1 Connecting 9299 SWITCHED PROBE 37

4.7.2 Setting 9299 SWITCHED PROBE 38

Chapter 5 Other Functions 39

5.1 Setting and Verifying Beep Sound 40

5.1.1 Setting Judgment Beep Sound 40

5.1.2 Setting Beep Sound During Key Press 41

5.2 Saving and Loading Test Conditions 42

5.2.1 Saving Test Conditions 42

5.2.2 Loading Test Conditions 44

5.3 Key Lock Function 45

5.4 System Reset 46

Chapter 6 External Interface 47

6.1 Controlling 3154 with External I/O 47

6.1.1 Terminal Connector Board/Signal Wires 48

6.1.2 Electric Specifications 50

6.1.3 Connecting External I/O Terminal 52

6.1.4 External I/O Terminal Circuit 54

6.1.5 Settings to be selected with VOLT 0 to 2

signals 55

6.1.6 Setting TEST Signal OFF Timing 57

6.1.7 Timing Chart 59

6.1.8 Output Signal Connection Example 61

6.1.9 Input Signal Connection Example 62

6.2 Analog Outputting 63

6.2.1 Connecting the 9094 OUTPUT CORD 63

6.2.2 Analog Output 64

6.2.3 Setting Analog Output 65

6.3 Outputting to Printer 66

6.3.1 Connecting Printer 70

6.3.2 Printing Example 71

Chapter 7 RS-232C Interface 73

7.1 Controlling from Personal Computer 74

7.1.1 Preparing for Data Transfer 75

7.1.2 Communication 77

7.1.3 Command Format 78

7.1.4 Numeric Format Chart 82

7.1.5 Command Reference 83

7.2 Sending Measurement Data to PC 97

Chapter 8 Specifications 101

8.1 General Specifications 101

8.2 Measurement Part Specifications 103

8.3 Dimensions 109

8.4 Options and specifications 110

Chapter 9 Maintenance and Service 113

9.1 Maintenance and Inspection 113

9.2 Trouble shooting 114

_____________________________________________________________________

Introduction

______________________________________________________________

Introduction

Thank you for purchasing the HIOKI "3154 DIGITAL MΩ

HiTESTER." To obtain maximum performance from the

product, please read this manual first, and keep it handy for

future reference.

Changes to Specifications

Changes are made to software version 1.10.

Software version appears following the model name (3154)

after start up.

・Measurement range is expanded up to 4000 MΩwith

test voltage at 500 V.

・Analog output voltage is changed from 4 V to 2 V when

2000 MΩis displayed with test voltage at 500 V.

・Outputs 4 V output with analog output at each resistance

range maximum value.

・Wider key entry selections to set lower limit values.

・Saved test conditions can be loaded using external I/O

VOLT 0 to 2 signals.

・External I/O TEST signal OFF timing setting display

appears as "tEStSIGnAL".

・The following four RS-232C commands are added;

:VOLTage:SIGNaL

:VOLTage:SIGNaL?

:AOUT:RANGe

:AOUT:RANGe?

_____________________________________________________________________

Inspection

______________________________________________________________

NOTE TEST PROBES are not included. Please purchase separately

according to your needs.

Ins

ection

When you receive the product, inspect it carefully to ensure

that no damage occurred during shipping. In particular,

check the accessories, panel switches, and connectors. If

damage is evident, or if it fails to operate according to the

specifications, contact your dealer or Hioki representative.

Accessories

Verify that following standard accessories are complete.

Instruction Manual 1

Grounded three-core power cord 1

Shipment of the unit

Use the original packing materials when reshipping the

product, if possible.

Warranty

HIOKI cannot be responsible for losses caused either

directly or indirectly by the use of the 3154 with other

equipment, or if ownership is transferred to a third party.

iii

_____________________________________________________________________

Safety Notes

______________________________________________________________

WARNING

This product is designed to conform to IEC 61010

Safety Standards, and has been thoroughly tested for

safety prior to shipment. However, mishandling during

use could result in injury or death, as well as damage

to the product. Be certain that you understand the

instructions and precautions in the manual before use.

We disclaim any responsibility for accidents or injuries

not resulting directly from product defects.

Safety Symbols

The symbol printed on the product indicates that the

user should refer to a corresponding topic in the

manual (marked with the symbol) before using the

relevant function.

In the manual, the symbol indicates particularly

important information that the user should read before

using the product.

Indicates the ON side of the power switch.

Indicates the OFF side of the power switch.

Indicates that dangerous voltage may be present at

this terminal.

Indicates AC (Alternating Current).

Indicates DC (Direct Current).

Safet

Notes

This manual contains information and warnings essential

for safe operation of the product and for maintaining it in

safe operating condition. Before using the product, be sure

to carefully read the following safety notes.

Tabla de contenidos

Otros manuales de Equipo de prueba de Hioki

Hioki

Hioki FT6380-50 Manual de usuario

Hioki

Hioki IR4055 Manual de usuario

Hioki

Hioki 3541 Manual de usuario

Hioki

Hioki FT3405 Manual de usuario

Hioki

Hioki 3290-10 Manual de usuario

Hioki

Hioki 3157 Manual de usuario

Hioki

Hioki 3415-01 Manual de usuario

Hioki

Hioki ST4030 Manual de usuario

Hioki

Hioki FT6380-90 Manual de usuario

Hioki

Hioki 3550 Manual de usuario

Hioki

Hioki HiTESTER 3540 Manual de usuario

Hioki

Hioki MEMORY HiCORDER 8855 Manual de usuario

Hioki

Hioki 9263 Manual de usuario

Hioki

Hioki 3118 Manual de usuario

Hioki

Hioki RM3543 Manual de usuario

Hioki

Hioki ST4030A Manual de usuario

Hioki

Hioki P2000 Manual de usuario

Hioki

Hioki 9262 Manual de usuario

Hioki

Hioki 3554 Manual de usuario

Hioki

Hioki 3145 Manual de usuario

Hioki

Hioki FT3151 Manual de usuario

Hioki

Hioki 3143 Manual de usuario

Hioki

Hioki 3665-20 Manual de usuario

Hioki

Hioki 3504-40 C HiTester Manual de usuario

Manuales populares de Equipo de prueba de otras marcas

SMART

SMART KANAAD SBT XTREME 3G Series Manual de usuario

Agilent Technologies

Agilent Technologies BERT Serial Manual de usuario

Agilent Technologies

Agilent Technologies N3280A Manual de usuario

Vernier

Vernier Go Direct Voltage Manual de usuario

Lifeloc

Lifeloc R.A.D.A.R. Manual de usuario

Fluke

Fluke T5-600 Instrucciones de funcionamiento e instalación

Mercury

Mercury TSL01 Manual de usuario

MAHA

MAHA MBT Series Manual de usuario

Fuji Electric

Fuji Electric P-61 Manual de usuario

ETC

ETC SealerAtor Manual de usuario

Skyfine

Skyfine ETHYWAY V2 Manual de usuario

Appion

Appion G5 Twin Manual de usuario

PCB Piezotronics

PCB Piezotronics 8159-0112A Manual de usuario

BW Technologies

BW Technologies MicroDock II Manual de usuario

Sun Nuclear

Sun Nuclear 1027 Manual de usuario

Biomark

Biomark HPR LITE READER Manual de usuario

Ashcroft

Ashcroft ATE-100 Manual de usuario

Rohde & Schwarz

Rohde & Schwarz RTA4000 Manual de usuario