Hioki 9518-02 Manual de usuario
Contents
Introduction i
Chapter 1 Before Use 1
1.1 Check of External Appearance and Accessories 1
1.2 Shipping Precautions 2
1.3 Notes on Use 3
1.4 Installing the GP-IB Interface 4
Chapter 2 Overview 5
2.1 Introduction to the GP-IB Interface 5
2.2 Features 5
2.3 Specifications 6
Chapter 3 Names of Parts 7
3.1 Controls and Connections 7
Chapter 4 Operation 9
4.1 Setting the GP-IB Device Address 9
4.2 Communication Methods by the GP-IB 11
4.3 Message Format 12
4.3.1 Program Message 12
4.3.2 Response Messages 12
4.4 Headers 13
4.5 Data Formats 14
4.6 Message Terminators 15
4.7 Separators 15
4.8 Abbreviation of Compound Commands 16
4.9 Output Queue 17
4.10 Input Buffer 17
4.11 Status Model 18
4.12 Status Byte Register 19
4.13 Event Registers 20
4.14 GP-IB Commands 24
Chapter 5 Command Reference 25
5.1 Command Summary 25
5.2 Format of Command Explanations 28
5.3 Standard Commands 29
5.4 Commands Specific to the 3157 34
5.5 Response Format for Queries as Numerical Value 66
5.6 Initialization Items 67
Chapter 6 Sample Programs 69
Chapter 7 Device Compliance Statement 75
Chapter 8 Troubleshooting 79
i
────────────────────────────────────────────────────
Introduction
────────────────────────────────────────────────────
WARNIN
G
Indicates that incorrect operation presents significant
danger of accident resulting in death or serious injury to
the user.
CAUTIO
N
Indicates that incorrect operation presents possibility of
injury to the user or damage to the equipment.
NOTE Denotes items of advice related to performance of the
equipment or to its correct operation.
I
ntroduction
Thank you for purchasing this HIOKI "9518-02 GP-IB INTERFACE."
To get the maximum performance from the unit, please read this manual first,
and keep this at hand.
This Instruction Manual provides information and warnings essential for
operating this equipment in a safe manner and for maintaining it in safe
operating condition. Before using this equipment, be sure to carefully read the
following safety notes.
The following symbols are used in this Instruction Manual to indicate the
relative importance of cautions and warnings.
* The "3157" in this Instruction Manual includes the "3157-01."
ii
────────────────────────────────────────────────────
Introduction
────────────────────────────────────────────────────
1
────────────────────────────────────────────────────
1.1 Check of External Appearance and Accessories
────────────────────────────────────────────────────
Chapter
1
Before Us
e
1
.1 Check of External Appearance and Accessories
When the unit is delivered, check and make sure that it has not been
damaged in transit. If the unit is damaged, or fails to operate according to the
specifications, contact your dealer or HIOKI representative.
(1) 9518-02 GP-IB INTERFACE
(2) This instruction manual
2
────────────────────────────────────────────────────
1.2 Shipping Precautions
────────────────────────────────────────────────────
1
.2 Shipping Precautions
If reshipping the unit, preferably use the original packing.
If this is not available, use the following procedure.
(1) Wrap the unit in plastic sheeting.
(2) After wrapping cushioning material around the unit, pack it into a
cardboard box, and then seal up the box with adhesive tape.
3
────────────────────────────────────────────────────
1.3 Notes on Use
────────────────────────────────────────────────────
1
.3 Notes on Use
(1) If you change the device address of the 3157 while using it, you should
immediately turn the power off and on again. If you do not do so, the address
change will not be registered by the bus, and problems will occur.
(2) Always be sure to secure the GP-IB cable to the 9518-02 unit by tightening up
the fixing screws provided.
(3) Program messages sent just after the power has been turned on are executed
after the self test has terminated.
(4) It is vital that the proper data format is used when inputting commands with
data values to the 3157 unit.
(5) For details of the various functions, refer to the instruction manual for the
3157 unit.
4
────────────────────────────────────────────────────
1.4 Installing the GP-IB Interface
────────────────────────────────────────────────────
WARNIN
G
To prevent electrical shock, before adding or replacing the GP-IB
interface, check that the power for the unit is off and the power cord
and connectors are disconnected. [The fixing screws must be firmly
tightened or the input unit may not function up to specification, or may
even fail.]
To avoid the danger of electric shock, never operate the unit with a
GP-IB interface removed. If you should wish to use the unit after
removing an interface, fit a blank panel over the opening of the removed
unit.
1
.4 Installing the GP-IB Interface
The space for fitting the 9518-02 GP-IB INTERFACE in the rear panel of the
3157 is covered with a blank panel. Follow these three steps to install the
9518-02 interface:
(1) Remove the fixing screws, and take off the blank panel.
(2) Insert the 9518-02 GP-IB INTERFACE into the exposed slot in the rear of
the unit in the figure below.
(3) Push the 9518-02 firmly into place, and fix with the screws removed in
step 1.
Tabla de contenidos
Otros manuales de Equipo de grabación de Hioki
Hioki
Hioki Memory HiCorder MR6000 Manual de instrucciones
Hioki
Hioki Memory HiCorder MR6000 Manual de instrucciones
Hioki
Hioki 3909 Manual de usuario
Hioki
Hioki 3920-01 Manual de usuario
Hioki
Hioki 9593-03 Manual de usuario
Hioki
Hioki 8205-10 Manual de usuario
Hioki
Hioki RS-232C Manual de usuario
Hioki
Hioki MR8847A Manual de usuario
Hioki
Hioki 9588 Manual de usuario
Hioki
Hioki 8860 Manual de usuario
Manuales populares de Equipo de grabación de otras marcas
Strymon
Strymon NIGHTSKY Manual de usuario
Mitsubishi Electric
Mitsubishi Electric 16CH DIGITAL RECORDER DX-TL5000U Manual de usuario
Tews Technologies
Tews Technologies TPMC465 Manual de usuario
Honeywell
Honeywell Excel 50 Manual de usuario
SeaLevel
SeaLevel COMM+8.LPCI Manual de usuario
Arturia
Arturia AUDIOFUSE STUDIO Manual de usuario
