Hillyard TRIDENT XM13SC Manual de usuario
Scrubbing machine
Use and Maintenance manual
Original istruction - DOC. 10074117- Ver. AA - 09-2017
3
CONTENTS
CONTENTS.......................................................................................................................3
SYMBOLS USED IN THE MANUAL ................................................................................5
PURPOSE AND CONTENT OF THE MANUAL...............................................................5
TARGET GROUP..............................................................................................................5
STORING THE USE AND MAINTENANCE MANUAL.....................................................5
ON DELIVERY OF THE APPLIANCE ..............................................................................5
INTRODUCTORY COMMENT ..........................................................................................5
IDENTIFICATION DATA....................................................................................................6
TECHNICAL DESCRIPTION ............................................................................................6
INTENDED USE................................................................................................................6
SAFETY ............................................................................................................................6
SERIAL NUMBER PLATE ................................................................................................6
TECHNICAL DATA............................................................................................................7
GENERAL SAFETY REGULATIONS...............................................................................8
SYMBOLS USED ON THE APPLIANCE........................................................................11
PREPARATION OF THE APPLIANCE...........................................................................11
HANDLING THE PACKED APPLIANCE....................................................................11
HOW TO UNPACK THE APPLIANCE .......................................................................11
HOW TO TRANSPORT THE APPLIANCE................................................................12
MAIN COMPONENTS OF THE APPLIANCE ............................................................12
MAIN APPLIANCE BODY COMPONENTS ...............................................................12
MAIN SOLUTION TANK COMPONENTS .................................................................13
MAIN RECOVERY TANK COMPONENTS................................................................13
MAIN VACUUM COVER COMPONENTS .................................................................13
MAIN STEERING COLUMN CONTROL COMPONENTS.........................................13
MAIN HANDLEBAR CONTROL COMPONENTS......................................................14
MAIN BATTERY CHARGING BASE COMPONENTS ...............................................14
APPLIANCE SAFETY................................................................................................14
BATTERY TYPE ........................................................................................................15
BATTERY MAINTENANCE AND DISPOSAL ............................................................15
INSERTING THE BATTERY INTO THE APPLIANCE ...............................................15
REMOVING THE BATTERY FROM THE APPLIANCE .............................................16
RECHARGING THE BATTERY .................................................................................16
CONTROL HANDLEBAR ADJUSTMENT .................................................................18
BATTERY CHARGE LEVEL INDICATOR..................................................................18
HOUR METER...........................................................................................................18
FILLING THE SOLUTION TANK ...............................................................................18
DETERGENT SOLUTION .........................................................................................20
INSERTING THE BRUSH INTO THE APPLIANCE...................................................20
PREPARING TO WORK .................................................................................................20
WORK .............................................................................................................................21
STARTING WORK.....................................................................................................21
"PRE-WASH" WORKING PROGRAM.......................................................................22
REGULATING THE DETERGENT ............................................................................23
4
OVERFLOW DEVICE ................................................................................................23
AT THE END OF WORK.................................................................................................24
MAINTENANCE..............................................................................................................25
RECOMMENDED MAINTENANCE OPERATIONS ..................................................25
CHECKING AND CLEANING THE RECOVERY TANK.............................................26
CHECKING AND CLEANING THE VACUUM COVER..............................................27
CHECKING AND CLEANING THE BRUSH ..............................................................28
CHECKING AND CLEANING THE SQUEEGEE BODY............................................28
CHECKING AND CLEANING THE VACUUM HOSE ................................................29
CHECKING AND CLEANING THE SOLUTION FILTER ..........................................30
CHECKING AND CLEANING THE SOLUTION TANK ..............................................30
TROUBLESHOOTING....................................................................................................32
DISPOSAL ......................................................................................................................34
SELECTION AND USE OF THE BRUSH.......................................................................34
5
Warning symbol:
Carefully read the sections marked with this symbol and observe the indications, for the safety of the operator and the
appliance.
Explosion risk symbol:
indicates that the battery may explode in certain conditions, if not handled in accordance with the directives indicated in
the manufacturer's manual.
Covered place symbol:
the operations preceded by this symbol must always be carried out in a dry, covered area.
Moving trolley warning symbol:
Indicates that the packed product should be handled with suitable lifting means that comply with the legal requirements.
Open book symbol with an "i":
Indicates the need to consult the instruction manual.
The descriptions contained in this document are not binding. The company therefore reserves the right to make any modications at any time
to elements, details, or accessory supply, as considered necessary for reasons of improvement or manufacturing/commercial requirements.
The reproduction, even partial, of the text and drawings contained in this document is prohibited by law.
The company reserves the right to make any technical and/or supply modications. The images are shown as a reference only, and
are not binding as to the actual design and/or equipment.
Open book symbol:
Tells the operator to read the manual before using the appliance.
Protective gloves symbol:
Always wear protective gloves, to avoid the risk of serious injury to your hands.
SYMBOLS USED IN THE MANUAL
PURPOSE AND CONTENT OF THE MANUAL
TARGET GROUP
STORING THE USE AND MAINTENANCE MANUAL
ON DELIVERY OF THE APPLIANCE
INTRODUCTORY COMMENT
The aim of this manual is to provide customers with all the information
needed to use the appliance in the safest, most appropriate and
most autonomous way. It includes information concerning technical
aspects, safety, operation, appliance downtime, maintenance, spare
parts and scrapping. Operators and qualied technicians must read
This manual is aimed at operators and qualied technicians
responsible for appliance maintenance. Operators must not perform
operations that should be carried out by qualied technicians. FIMAP
The Use and Maintenance Manual must be stored in its special
pouch close to the appliance, protected from liquids and anything
When the machine is delivered to the customer, an immediate
check must be performed to ensure all the material mentioned in
the shipping documents has been received, in addition to verifying
that the equipment has not been damaged during transportation. If
Any type of equipment can only work properly and eectively if used
correctly and kept in full working order by performing the maintenance
operations described in the attached documentation. You should
therefore read this instruction manual carefully, consulting it again
the instructions in this manual carefully before carrying out any
operation on the appliance. If in doubt about the correct interpretation
of instructions, contact your nearest Customer Service Centre to
obtain the necessary clarications.
SpA cannot be held liable for damages resulting from failure to
comply with this prohibition.
else that could compromise its legibility.
this is the case, the carrier must ascertain the extent of the damage
at once, informing our customer service oce. It is only by prompt
action of this type that the missing material can be obtained, and
compensation for damage successfully claimed.
if issues arise while using the machine. If necessary, remember that
our assistance service (organised in collaboration with our dealers)
is always available for advice or direct intervention.
6
IDENTIFICATION DATA
For technical assistance or to request replacement parts, always
give the model, the version and serial number written on the serial
number plate.
TECHNICAL DESCRIPTION
INTENDED USE
SAFETY
SERIAL NUMBER PLATE
The TRIDENT XM13SC is a scrubbing machine that is able to clean
a wide range of ooring and dirt types by means of the mechanical
action of the discoidal brush and the chemical action of a water-
detergent solution. As it advances, it also collects the dirt that has
This scrubbing machine was designed and built for the cleaning
(scrubbing and drying) of smooth, compact ooring in the
commercial, residential and industrial sectors by a qualied operator
in proven safety conditions. The scrubbing machine is not suitable
for cleaning rugs or carpets. The appliance is only suitable for use in
indoor - or at least covered - areas.
Operator cooperation is paramount for accident prevention. No
accident prevention programme can be eective without the full
co-operation of the operator who is directly responsible for machine
operation. The majority of occupational accidents that happen both
in the workplace or whilst moving are caused by failure to respect
The serial number plate is located on the inside of the appliance in
the front end of the frame, indicating its general characteristics (in
particular, the serial number). The serial number is a very important
piece of information and should always be provided together with any
request for assistance or when purchasing spare parts.
ATTENTION: The appliance is not suitable for use in the rain,
or under jets of water.
IT IS FORBIDDEN to use the appliance for picking up dangerous
dusts or inammable liquids in places with an explosive atmosphere.
In addition, it is not suitable as a means of transport for people or
objects.
the most basic safety rules. An attentive, careful operator is most
eective guarantee against accidents and is fundamental in order to
implement any prevention programme.
been removed and the detergent solution that has not been absorbed
by the oor. The appliance must only be used for this purpose.
7
TECHNICAL DATA U/M TRIDENT
XM13SC
Working width in 11
Squeegee width in 12,8
Working capacity, up to ft2/h 6.027,75
Maximum gradient with full load % 2
Total power W 255
Disc brush no. / Ø in 1 / 11
Brush motor V/W 36 / 90
Disc brush rotations rpm 150
Maximum pressure on the brush lb 22
Vacuum motor V/W 36 / 150
Suction vacuum psi 0,33
Vacuum cleaner (Eco-mode) psi 0,22
Rear wheels (Number / (Diameter / Width)) no. / (Ø in / in) 2 / (6,3 / 1,18)
Solution tank gal 0,8
Recovery tank gal 0,95
Machine length in 21,8
Machine length (Handlebar in maintenance position) in 35,2
Machine body height (Control handlebar joint) in 11,4
Control handlebar height (Handlebar in resting position) in 41,3
Machine height (Handlebar in maintenance position) in 13,8
Machine width (with squeegee) in 14,75
Rated battery voltage V 36.5
Battery weight lb 3
Machine weight (machine + brush + squeegee) lb 39,7
Machine weight in transport (machine + battery + brush + squeegee) lb 44,1
Machine weight in running order (machine + battery+ water + brush + squeegee) lb 50,7
Sound pressure level (ISO 11201) - Lpa dB (A) <70
Uncertainty Kpa dB (A) 1.5
Hand vibration level (ISO 5349) m/s2<2.5
Uncertainty of measurement of vibrations -
8
The regulations below must be carefully followed in order to avoid
harm to the operator and damage to the appliance.
WARNING:
• Carefully read the labels on the appliance. Do not cover them
for any reason and replace them immediately if they become
damaged.
• The appliance must always be stored and used in a closed
place.
• The appliance must be only used by authorised, trained
personnel.
• Do not use the appliance on surfaces with an inclination greater
than the one shown on the serial number plate.
• The appliance is not suitable for cleaning rough or uneven
oors. Do not use the appliance on slopes.
• If the battery recharge cable is damaged, contact an authorised
service centre immediately.
• In the event of danger, promptly remove the battery from the rear
part of the appliance (refer to the "REMOVING THE BATTERY"
paragraph).
• For all maintenance interventions, switch o the machine using
the main switch and remove the battery.
• To prevent the appliance from being activated accidentally, the
power supply must be disconnected, the appliance must be
switched o using the main switch, and the battery must be
removed.
• Children must be supervised to ensure they do not play with the
device.
• When using the appliance, pay attention to other people and
especially to children.
• Only use the brushes supplied with the machine, or those
specied in the "CHOOSING AND USING THE BRUSHES"
paragraph of the instruction manual. The use of other brushes
GENERAL SAFETY REGULATIONS
9
could compromise safety levels.
• The appliance must only be powered with a voltage equal to
that shown on the serial number plate.
• When left unattended, the appliance must be protected from
unintentional movements.
The appliance must not be transported
or parked in its idle position when the
solution tank and recovery tank are full.
WARNING:
• The appliance must not be used or kept outdoors, in damp
conditions or directly exposed to rain.
• The appliance must be stored in an enclosed area with a
temperature between -13°F and +131°F.
• Conditions of use: room temperature between 32°F and 104°F,
with relative humidity between 30 and 95%.
• The socket for the battery power cable must have an earth
connection in compliance with the regulatory standards.
• The appliance does not cause harmful vibrations.
• Never pick up gases, explosive/inammable liquids or powders,
nor acids and solvents! These include gasoline, paint thinners
and fuel oil (which, when mixed with the vacuum air, can form
explosive vapours or mixtures), and also non-diluted acids and
solvents, acetones, aluminium and magnesium powders. These
substances may also corrode the materials used to construct
the appliance.
• If the appliance is to be used in dangerous areas (for example,
gas stations), ensure that all relevant safety regulations are
observed. The appliance must never be used in environments
with a potentially explosive atmosphere.
10
• Do not place any liquid containers on the appliance.
• In the event of a re, use a powder extinguisher. Do not use
water.
• Adapt the speed to the adhesion conditions.
• Avoid working with the brushes when the machine is standing
still, so as not to damage the oor.
• Do not knock against shelving or scaolding, where there is a
danger of falling objects. The operator must always be equipped
with the appropriate safety devices (gloves, shoes, helmet,
goggles, etc.).
• If the appliance does not work properly, check this is not caused
by failure to carry out routine maintenance. Otherwise, ask for
intervention of the authorised technical assistance centre.
• If you need to replace any components, request the ORIGINAL
spare parts from an Authorised dealer and/or Retailer.
• Restore all electrical connections after any maintenance
interventions.
• Have the appliance checked by an authorised technical
assistance centre every year.
• When disposing of consumable materials, observe the laws
and regulations in force. When, after years of valuable work,
your appliance needs to be nally decommissioned, dispose of
the materials contained within it appropriately, bearing in mind
that the appliance is made of fully recyclable materials.
Otros manuales para TRIDENT XM13SC
1
Tabla de contenidos
Otros manuales de Depurador de Hillyard
Hillyard
Hillyard TRIDENT R22SC Manual de usuario
Hillyard
Hillyard TRIDENT R36 SC PLUS Manual de usuario
Hillyard
Hillyard TRIDENT R30SC Manual de usuario
Hillyard
Hillyard TRIDENT R30SC Manual de usuario
Hillyard
Hillyard TRIDENT R26SC PRO Manual de usuario
Hillyard
Hillyard TRIDENT B20SC Manual de usuario
Hillyard
Hillyard TRIDENT NM14 Manual de usuario
Hillyard
Hillyard TRIDENT T30SC PRO Manual de usuario
Hillyard
Hillyard TRIDENT T20SC PRO Manual de usuario
