Hillstone A200 Series Manual de operación y mantenimiento
Hillstone A200 Series Hardware
Reference Guide
Copyright 2021Hillstone Networks. All rights reserved.
Information in this document is subject to change without notice. The software described in this document is
furnished under a license agreement or nondisclosure agreement. The software may be used or copied only in
accordance with the terms of those agreements. No part of this publication may be reproduced, stored in a retrieval
system, or transmitted in any form or any means electronic or mechanical, including photocopying and recording for
any purpose other than the purchaser's personal use without the written permission of Hillstone Networks.
Hillstone Networks
This document is prohibited for any commercial purpose.
About This Manual
This document is an installation guide for Hillstone devices to help you install the Hillstone device
properly.
For more information, refer to the documentation site: https://docs.hillstonenet.com.cn
To provide feedback on the documentation, please write to us at: TechDocs@hillstonenet.com
Contact Information:
US Headquarters:
5201 Great America Pkwy, #420
Santa Clara, CA 95054
https://www.hillstonenet.com.cn/about/contact_Hillstone.html
Hillstone Networks
www.hillstonenet.com
TWNO: TW-HW-AS-CN-V1.0-9/7/2021
3
Contents
Contents ...................................................................................................................................... 3
Preface ......................................................................................................................................... 6
About This Manual................................................................................................................ 6
Document Conventions........................................................................................................ 6
Chapter 1 Introduction ............................................................................................................. 6
Overview ................................................................................................................................. 6
Hardware Overview............................................................................................................... 7
Front Panel.......................................................................................................................... 7
Back Panel ........................................................................................................................... 7
LED Indicators ...................................................................................................................... 7
System Parameters ................................................................................................................. 8
Ports ......................................................................................................................................... 9
CON port ............................................................................................................................ 9
USB Port............................................................................................................................ 10
Gigabit Ethernet Port...................................................................................................... 10
SFP Port............................................................................................................................. 10
CLR Button........................................................................................................................... 13
Power Supply........................................................................................................................ 13
Power Supply Modules.................................................................................................... 13
Chapter 2 Installation Preparations....................................................................................... 14
Introduction.......................................................................................................................... 14
Installation Site Environment Requirements................................................................... 14
Temperature/Humidity Requirements ......................................................................... 14
Clearness Requirements................................................................................................... 14
ESD Prevention................................................................................................................ 14
EMI Prevention................................................................................................................ 15
Other Safety Recommendations........................................................................................ 15
4
Verifying the Parts Received .............................................................................................. 15
Installation Devices/Tools/Cables ................................................................................... 16
Chapter 3 Installation.............................................................................................................. 16
Installing the Device on a Workbench ............................................................................. 16
Connecting Cables ............................................................................................................... 17
Connecting the Console Cable....................................................................................... 17
Connecting the Ethernet Cable...................................................................................... 18
Connecting the Ethernet Copper Cable.................................................................... 18
Connecting the Ethernet Fiber Cable........................................................................ 18
Connecting a Power Adapter.......................................................................................... 19
Verifying Installation........................................................................................................ 19
Chapter 4 Boot and Configuration........................................................................................ 21
Introduction.......................................................................................................................... 21
Establishing a Configuration Environment ..................................................................... 21
Console (CON) Connection........................................................................................... 21
WebUI................................................................................................................................ 22
Telnet or SSH.................................................................................................................... 23
Basic Configuration ............................................................................................................. 23
Chapter 5 Hardware Maintenance and Replacement ......................................................... 24
Introduction.......................................................................................................................... 24
Startup.................................................................................................................................... 24
Shutdown .............................................................................................................................. 24
Chapter 6 Troubleshooting .................................................................................................... 24
Introduction.......................................................................................................................... 24
Losing the Administrator Password.................................................................................. 24
Chapter 7 Addendum Statement ........................................................................................... 26
FCC Statement ..................................................................................................................... 26
Industry Canada Statement................................................................................................. 26
Avis d'Industrie Canada ...................................................................................................... 27
6
Preface
About This Manual
Thanks for choosing the network security products from Hillstone Networks.
This document is an installation manual for the Hillstone A200Series device to help you install the
device properly.
This manual includes the following chapters:
Introduction
Installation Preparations
Installation
Boot and Configuration
Hardware Maintenance and Replacement
Troubleshooting
Document Conventions
This manual uses the following conventions for your convenience to read and understand:
Warning: Indicates improper operation that may cause serious damage to equipment or
injury to operators. Thus, operators must strictly follow the operation rules.
Caution: Indicates incorrect operation that may affect the normal use of the equipment.
Operators should be careful.
Note: Indicates information that may help readers understand the content.
Chapter 1 Introduction
Overview
The A200 series equipment of Shanshi Netcom is the gateway equipment based on ARM architecture
of Shanshi Netcom, which supports large capacity local. storageCurrently, A200-Series product models
include A200、A200W.
7
Hardware Overview
The size of A200 series equipment of Shanshi Netcom is 180 * 110 * 28mm, which belongs to
desktop equipment and is used on the workbench.
Front Panel
The front panel of A200 consists of several LED indicators (1 Power LED, 1 Status LED).
Figure: A200 Front Panel
The front panel of A200W consists of several LED indicators (1 Power LED, 1 Status LED, 1 WLAN
LED).
Figure: A200W Front Panel
Back Panel
The A200 is powered by a power adapter, and the rear panel has a DC power interface, a CLR key, a
USB interface, a con port, an SFP optical port, and five Gigabit electrical ports.
Figure: A200 Back Panel
LED Indicators
The following table describes the meanings of LED indicators on the front panels of A200-Series
devices.
Power
LED
Status LED
Power
LED
Status LED
WLAN
LED
8
Table: Front Panel LED Descriptions
LED
Color/Status
Description
PWR
Green/Always on
The device power is running
normally.
Off
The device is powered off.
STA
Green/Blinking
The system is running normally.
Off
The system has not been booted/is
booting/has failed to boot.
WLAN
Green/Always on
The device has detected a built-in
WLAN module present.
Green/Blinking
WLAN is in data receiving and
sending state
LNK
Green/Always on
The link between this port and its
peer device is in normal status.
Off
The link between this port and its
peer device has failed or there is no
connection.
ACT
Yellow/Always on
The link between this port and its
peer device is in normal status.
Yellow/Blinking
The port is sending or receiving data.
Off
No data is transmitted on this port.
Notes:
The STA LED will remain OFF when there is a boot failure caused by OS software
damage. Contact your sales representative if this occurs.
As the number and type of LED indicators may vary from different product models,
please refer to the actual product.
System Parameters
The following table lists the system parameters of A200-Series devices.
9
Table: System Parameters
Item
Description
Fixed Ports
A200 Series
5 Gigabit port
1 USB 3.0 ports
1 CON port
1 SFP Smooth Mouth
CPU
88f3720 Binuclear
DDR4 SDRAM
2GB
Flash Memory
4GB
Dimensions (W×D×H)
W180.0mm * D110.0mm *H28.0mm
Weight
Net weight: 0.64kg
Gross weight:1.276 kg (accessories
and packages included)
Power Rating
14W
Input Voltage
AC
100-240V AC, 50/60Hz
Ambient Temperature
0℃-45℃
Relative Humidity
5%-90% (non-condensing)
Ports
This section introduces attributes of ports on the A200-Series device, including the CON port, USB
ports, gigabit Ethernet ports, SFP ports.
CON port
The A200 series equipment of Shanshi Netcom provides a configuration port (con port) that conforms to RS-232C asynchronous serial
specification. Through this configuration port, the user can configure the device by himself. The properties and description of the
configuration port are shown in the following table.Table: Console Port Attributes
Attribute
Description
Connector
RJ-45
10
Attribute
Description
Port Standard
RS-232C
Baud Rate
115200 bit/s
Services
Connect the CON port to the serial port of a PC and
run a terminal emulation program on the PC to
configure the device
Transmission Medium
Console cable
USB Port
The A200-Series device provides up to 1 USB 2.0 host ports. Attributes for the USB host ports are
shown in the table below:
Table: USB 2.0 Host Port Attributes
Attribute
Description
Connector
USB Type-A interface
Port Standard
USB 2.0 host interface
Negotiation Mode
1.1/2.0 autosensing
Gigabit Ethernet Port
The A200-Series device provides several fixed gigabit Ethernet ports. Attributes for the gigabit
Ethernet ports are shown in the table below:
Table: Gigabit Ethernet Port Attributes
Attribute
Description
Connector
RJ-45
Port Standard
Auto-MDI/MDIX (crossover cable and straight-through cable
autosensing)
Frame Format
Ethernet_II
Ethernet_SNAP
Negotiation
Mode
10/100/1000Mbps autosensing
Full/half-duplex
SFP Port
The A200-Series device provides several SFP ports. Attributes for the SFP ports are shown in the table
below:
Tabla de contenidos
Otros manuales de Cortafuegos de Hillstone
Hillstone
Hillstone HLB480-375 Manual de usuario
Hillstone
Hillstone SG-6000-X7180 Manual de operación y mantenimiento
Hillstone
Hillstone SG-6000-E6360 Manual de operación y mantenimiento
Hillstone
Hillstone SG-6000 E Series Manual de operación y mantenimiento
Hillstone
Hillstone SG-6000-X7180 Manual de operación y mantenimiento
Hillstone
Hillstone SG-6000 X Series Manual de usuario
Hillstone
Hillstone SG-6000-X5100 Manual de usuario
Hillstone
Hillstone SG-6000 X-Series Manual de usuario
