HIK VISION DS-PDP18-HM Manual de usuario

DS-PDP18-HM

Wired Double PIR Detector

User Manual

EN50131-2-2:2021

Security Grade 2

Environment Class IV

Hangzhou Hikvision Digital Technology CO.,Ltd. No.555 Qianmo Road, Binjiang District, Hangzhou 310052, China

UD33808B

User Manual Flow Chart

1 Appearance

2 Installation

Bracket Tamper

67.3 mm

141.6 mm

60.0 mm

Tamper Switch

LED Jumper

PIR Sensitivity Jumper

High and Low Mounting Adjustment Lever

H Model (default): 2.5 to 3 m (typical 2.7 m)

L Model: 0.8 to 1.2 m (typical 1 m)

LED OFF

Pet Immunity

LED ON (default)

Auto (default)

1.1 Unbox.

1.2 Check components.

Select the wiring type and

connect the detector to the

control panel.

2.1 Confirm environment.

2.2 Fix the device (Wall

mounting/Bracket mounting).

Check detection range

in H and L mode.

Check the indicator,

and the device is

powered on.

1 Appearance

3 Connect to

Control Panel

2 Installation

5 Detection Range

4 Power on

Installation Environment

Facing Direct

Strong Light

Source of

air currents

Facing reflective

surfaces

Areas with

moving objects

Surface that absorb heat or

rapid temperature change area

1Wall Mounting

1. Adjust the knob to the

unlock icon.

2. Press the button.

3. Remove the rear panel.

Wire Slot

4. Method 1 (Recommended):

Thread the cables through the

middle wire hole on the rear panel.

5. Fix the rear panel to the

corresponding position on the wall

with two screws. Remove the wiring

terminal and finish wiring.

Wire Terminal

6. Install the wiring terminal

back and fix the cables into

the wire slot.

7. Adjust the high and low

mounting adjustment lever,

and Install the front panel.

8. Adjust the knob to the lock icon.

Back of Wire hole

4. Method 2: Thread the

cables through the wire

hole on the rear panel.

2Bracket Mounting

4. Install the bracket to the wall.

6. Remove the bracket tamper

cover on the front panel.

7. Connect the tamper cable to the front

panel, and fix the cable into the wire slot.

8. Adjust the high and low mounting

adjustment lever, and install the front panel.

1. Adjust the knob to the

unlock icon.

2. Press the button.

3. Remove the rear panel.

5. Install the wiring terminal back and fix the

cables into the wire slot. Thread the tamper

cable through the wire hole, and fix the rear

panel to the bracket with one screw.

Wire Slot

9. Adjust the knob to the lock icon.

Wire Slot

3 Connect to Control Panel Note: The resistor needs to be connected to the end of detector.

1None Resistor Connection

Single EOL Connection

Double EOL Connection

Triple EOL Connection

Control Panel

Detector

ALARMTAMPER +-

EOL EOL

ALARMTAMPER +-

EOL EOL

ALARMTAMPER +-

EOL EOL

ALARMTAMPER +-

EOL EOL

ZONE1

ZONE2

COM

+ -

ZONE2ZONE1 COM

TAMPER/ALARM

2.2 K

TAMPER/ALARM

ALARMTAMPER

2.2 K

2.2 K2.2 K

2.2 K

FAULT TAMPER ALARM

1 K

1 K1 K

2.2 K

2.2 K 1 K

2.2 K

Alarm: 1K, 2K2, 4K7, 5K6, 6K8

Tamper: 1K, 2K2, 4K7, 5K6

4K7

2K2

5K6

6K8

4K7

2K2

5K6

6K8

ALARM +

EOL

TAMPER

EOL

ALARM +

EOL

TAMPER

EOL

ALARM

TAMPER

4K7

2K2

5K6

For double and triple EOL connection, the detector has two method for resistor wiring:

(1) Use jumpers to select the End of Line resistance (Control panel dependent) on the ALARM/TAMPER pins.

(2) Select an resistance (Control panel dependent), and add the resistor to ALARM/TAMPER wiring ports of the detector.

Please select one resistor wiring method according to the figure below.

ALARM

TAMPER

4K7

2K2

5K6

2.2 K

1 K

FAULT

4 Power on

After powering on, the indicator flashes rapidly. Once the detector self test

is completed, the LED indicator will go out until the detector detects movement.

NOT READY READY

6 Specification

Detection

performance

Detection method Passive Infrared

Detection range 18 m (16m EN certified)

Detection angle 90°

Detection zones 118

Detectable speed 0.3 to 2 m/s

Sensitivity Auto, Pet

White light filter 20000 lux

Pet immunity Up to 24 Kg

Digital temperature compensation Support

Feature

Digital processing Support

Sealed optics Support

Tamper protection Front, Rear

Software features End of line resistance Alarm: 1K, 2K2, 4K7, 5K6, 6K8

Tamper: 1K, 2K2, 4K7, 5K6

Hardware features Alarm output Normally Closed

Interface LED Blue (Alarm), Orange (Fault)

Electrical

characteristics

Power supply 9 to 16 VDC

Typical voltage 12 VDC

Power consumption Maximum current: 15 mA @12 VDC

Quiescent current: 8 mA@12 VDC

General

Operation temperature -25 °C to 70 °C (-13 °F to 158 °F)

Storage temperature -25 °C to 70 °C (-13 °F to 158 °F)

Operation humidity 10% to 90%

IP rate IP65

Dimension (W x H x D) 67.3 × 142.0 × 60.0 mm

Weight 226.3 g

Mounting height 2.5 to 3 m High Mount

0.8 to 1.2 m Low Mount

Mounting method Wall

Application scenario Indoor, Outdoor

5 Detection Range

Top View

Side View

High Mounting

Low Mounting

12m

16m

0m 0 4m8m 4m 8m 12m12m

2.7m

16m14m12m10m2m 4m 6m 8m

1.2m

16m14m12m10m2m 4m 6m 8m

Otros manuales de Sensor de seguridad de HIK VISION

HIK VISION

HIK VISION DS-PDMCS-EG2-WB Manual de usuario

HIK VISION

HIK VISION DS-PDBG8-EG2-WE Manual de usuario

HIK VISION

HIK VISION DS-PD2-D10P-W1 Manual de usuario

HIK VISION

HIK VISION DS-PDMCK-EG2-WE Manual de usuario

HIK VISION

HIK VISION DS-PDCO-E-WB Manual de usuario

HIK VISION

HIK VISION DS-PDCL12-EG2-WB Manual de usuario

HIK VISION

HIK VISION DS-PDMC-EG2-WB Manual de usuario

HIK VISION

HIK VISION DS-PDTT15AM-LM-WB Manual de usuario

HIK VISION

HIK VISION Pyronix XDH10TT-WE Manual de usuario

HIK VISION

HIK VISION DS-PD2-T12P-WEL Manual de usuario

HIK VISION

HIK VISION DS-PD2-P10P-W Manual de usuario

HIK VISION

HIK VISION DS-PD2-P15C-W Manual de usuario

HIK VISION

HIK VISION DS-PDP15P-EG2-WB Manual de usuario

HIK VISION

HIK VISION DS-K5032-3XFD Manual de usuario

HIK VISION

HIK VISION DS-PDMCX-E-WB Manual de usuario

HIK VISION

HIK VISION DS-PDPC12PF-EG2-WB Manual de usuario

HIK VISION

HIK VISION DS-PD2-T12P-WEL Manual de usuario

HIK VISION

HIK VISION DS-PDD12P-EG2-WE Manual de usuario

HIK VISION

HIK VISION DS-PDC15-EG2-WE Manual de usuario

HIK VISION

HIK VISION AX PRO Series Manual de usuario

HIK VISION

HIK VISION DS-PDQP15AM-LM-WE Manual de usuario

HIK VISION

HIK VISION DS-PDMC-EG2-WE Manual de usuario

HIK VISION

HIK VISION DS-PDMCX-E-WB Manual de usuario

HIK VISION

HIK VISION DS-PDPG12P-EG2-WB Manual de usuario

Manuales populares de Sensor de seguridad de otras marcas

THORLABS

THORLABS PDA10JT Manual de usuario

Waeco

Waeco UV-DETECT Manual de usuario

Intermatic

Intermatic IOS-DSIMF Manual de usuario

urmet domus

urmet domus 1083 Manual de usuario

Siemens

Siemens AZL66 Series Manual de usuario

BTI

BTI Profiline Multi Finder Manual de usuario

Challenger

Challenger SL01 Manual de usuario

DMP Electronics

DMP Electronics 1122INT Manual de usuario

Rielta

Rielta Ladoga MK-RK Manual de usuario

Mirion Technologies

Mirion Technologies ACCURAD PRD Manual de usuario

Bosch

Bosch DS835 Manual de usuario

DBI SALA

DBI SALA EZ Stop Manual del operador

Lamptime

Lamptime ST05C Manual de usuario

Ubiquiti

Ubiquiti MFI-MSC Manual de usuario

Subsite

Subsite 910R Instrucciones de instalación

Satel

Satel OPAL Pro Manual de usuario

Aleph

Aleph XC-1XTEU Manual de usuario

Pima

Pima LARIS QUAD Manual de usuario