HIK VISION DS-9500 Series NVR Guía del usuario

DS-9500 Series NVR

Quick Operation Guide

Version 1.3.1

DS-9500 SeriesNVR Quick Operation Guide

Verify Contents

Verify that the package contents are correct by checking the items against the packing list.

Note: Please contact your dealer for damaged or missing items.

NVR Pre-Installation

The DS-9500 Series NVR is highly advanced surveillance equipment that should be installed with care. Please

take into consideration the following precautionary steps before installation of the NVR.

1. Keep all liquids away from the NVR.

2. Install the NVR in a well-ventilated and dust-free area.

3. Ensure environmental conditions meet factory specifications.

4. Install a manufacturer recommended HDD.

NVR Installation

During the installation of the NVR:

1. Use brackets for rack mounting.

2. Ensure there is ample room for audio and video cables.

3. When installing cables, ensure that the bend radius of the cables are no less than five times than its diameter.

4. Connectboth thealarm and RS-485 cable.

5. Allow at least 2cm (~0.75in) of space between racks mounted devices.

6. Ensure the NVR is grounded.

7. Environmental temperature should be within the range of -10 ºC ~ 55 ºC, 14ºF ~ 131ºF.

8. Environmental humidity should be within the range of 10% ~ 90%.

Hard Disk Installation

Before installing a hard disk drive (HDD), please make sure the power is disconnected from the NVR. A factory

recommended HDD should be used for this installation.

Tools Required: Screwdriver.

1. Use the screws to install HDD to its mounting bracket.

2. Press the latches on both sides of the front panel of NVR chassis to open it.

3. Inser the HDD bracket to the chassis along the slot unitl it has fully seated i nto pos ition.

4. Close the front panel of the NVR chassis.

DS-9500 SeriesNVR Quick Operation Guide

Front Panel

DS-9508NI-S/R Front Panel

No. Name Description

Status

LED

Indicators

Power Turning red indicates power supply but without system running, turning blue

indicates power supply and system running.

Alarm Alarm indicator turns red when a sensor alarm is detected.

TX/RX TX/RX indictor blinks blue wh

en network connection is functioning

properly.

HDD HDD indicator blinks red when data is being read from or written to HDD.

Ready Ready indicator turns blue when NVR is functioning properly.

Backup Backup indicator blinks blue when data is beingbackup.

2 USB Ports

Universal Serial Bus (USB) ports for additional devices such as USB mouse

and USB Hard Disk Drive (HDD).

3 Power Button Powers NVR on/off.

4 Backup Button Backup video files.

5 Channel Status Indicators Blue indicates recording, red indicates network connection, purple indicates

recording & network connection.

DS-9516NI-S/R Front Panel:

No. Name Description

Status

LED

Indicators

Power

Turning red indicates power supply but without system running, turning blue

indicates power supply and system running.

Alarm Alarm indicator turns red when a sensor alarm is detected.

TX/RX

TX/RX indictor blinks blue when network connection is functioning

properly.

DS-9500 SeriesNVR Quick Operation Guide

HDD HDD indicator blinks red when datais beingread from or written to HDD.

Ready Ready indicator turns blue when NVR is functioning properly.

Backup Backup indicator blinks blue when data is beingbackup.

2 Backup Button Backup video files.

3 USB Ports Universal Serial Bus (USB) ports for additional devices such as USB mouse

and USB Hard Disk Drive (HDD).

4 Power Button Powers NVR on/off.

5 ChannelStatus

Indicators

Blue indicates recording, red indicates network connection, purple indicates

recording & network connection.

Rear Panel

DS-9508NI-S/R Rear Panel:

No. Item Description

1 RESET Press and hold it for 10 seconds to reset all parameters to factory defaults.

2 RS-232 Connect to RS-232 devices.

3 LAN 10/100/1000Mbps Self-adaptive UTP Ethernet interface.

4 eSATA Backup/extended storage interface, connect to external SATA disk,

CD-RW, disk array, etc.

The eSATA interface is provided for DS-9500NI-R bydefault and

optional for DS-9500NI-S.

5 RS-485 Matching

Resistor Switch (SW)

Connection of 120-ohm terminator for RS-485 bus. ON=connected;

OFF=disconnected.

RS-485 Connect to RS-485 devices, e.g., P/T receiver, etc. Use the T+ and T－

terminals of RS-485 interface to connect to the R+ and R- terminals of the

receiver.

ALARM IN 16 relay alarm inputs

ALARM OUT 4 relay alarm outputs

7 GND Grounding

8 POWER 220VAC power supply

DS-9500 SeriesNVR Quick Operation Guide

DS-9516NI-S/R Rear Panel:

No. Item Description

1 RESET Press and hold it for 10 seconds to reset all parameters to factory defaults

2 RS-232 Connect to RS-232 devices

3 LAN 10/100/1000Mbps Self-adaptive UTP Ethernet interface.

4 eSATA Backup/extended storage interface, connect to external SATA disk,

CD-RW, disk array, etc.

The eSATA interface is provided for DS-9500NI-R bydefault and

optional for DS-9500NI-S.

5 RS-485 Matching

Resistor Switch (SW)

Connection of 120-ohm terminator for RS-485 bus. ON=connected;

OFF=disconnected.

RS-485 Connect to RS-485 devices, e.g., P/T receiver, etc. Use the T+ and T－

terminals of RS-485 interface to connect to the R+ and R- terminals of the

receiver.

ALARM IN 16 relay alarm inputs

ALARM OUT 4 relay alarm outputs

7 GND Grounding

8 POWER 220VAC power supply

Note: Currently the RS-485 interface of DS-9500 NVR is reserved for future use.

Connections

Connecting to Alarm Input/Output Device

The alarm input/output interface of the NVR is shown below:

The alarm input is an open/close relay. If the input is not an open/closed relay, follow the connection diagram below:

DS-9500 SeriesNVR Quick Operation Guide

Relay alarm

input

Relay alarm

input

NVR

To connect to an AC/DC load, use the following diagram:

Relay alarm

output

NVR

For DC load, JP4 can be used within the limit of 12V/1A safely. If the interface is connected to an AC load, JP4 should be left

open. Use an external relay for safety (as show n in the figure above).

Note: An external relay is needed to prevent electric shock when connecting to an AC load.

Alarm Connections:

The device provides the green mating plugs for alarminput and alarm output connectors. Operate the following steps:

1. Remove the green mating plugfrom the ALARM IN or ALARM OUT connector.

2. Use the screwdriver to loosen the screw in the plug and then place the wire to the top o f screw and finally tighten the screw

to secure the wires.

3. Insert the plug to its mating slot.

DS-9500 SeriesNVR Quick Operation Guide

Specifications

DS-9500NI-S:

Model DS-9508NI-S DS-9516NI-S

Video/Audio input IP video input

8-ch 4CIF /4-ch 720P /2-ch

UXGA /1080P real time, or

4-ch UXGA /1080P /2-ch 5

Megapixel not real time

16-ch 4CIF /8-ch 720P /4-ch

UXGA /1080P real time, or 8-ch

UXGA /1080P /4-ch 5 Megapixel

notreal time

Hard disk

SATA

8 SATA interfaces

Capacity Each interface supports up to 2TB capacity

External interface

Network

interface 1,RJ-45, 10 /100 /1000 Mbps adaptive Ethernet interface

Serial interface

1 RS-232 interface (for parameters configuration, maintenance ,

transparent channel);

1 RS-485 interface (for PTZ control);

1 RS-485 keyboard interface (for special keyboard control)

USB interface 2, USB 2.0

Alarm in 16

Alarmout 4

General

Power

supply 100 ~ 240VAC, 6.3A, 50 ~ 60Hz

Consumption ≤20 W(without hard disk or DVD-R/W)

Working

temperature -10℃~ +55℃

Working

humidity

10% ~ 90%

Chassis 19-inch rack-mounted 2U chassis

Dimensions

(W × D × H) 450 × 450 × 95 mm

Weight ≤8 kg ( without hard diskor DVD-R/W )

DS-9500 SeriesNVR Quick Operation Guide

DS-9500NI-R:

Model DS-9508NI-R DS-9516NI-R

Video/Audio input IP video input

8-ch 4CIF /4-ch 720P /2-ch

UXGA /1080P real time, or

4-ch UXGA /1080P /2-ch 5

Megapixel not real time

16-ch 4CIF /8-ch 720P /4-ch

UXGA /1080P real time, or 8-ch

UXGA /1080P /4-ch 5 Megapixel

notreal time

Hard disk

SATA 8 SATA interfaces

eSATA 1 eSATA interface

Capacity Up to 2TB capacity for each disk

Disk array

Array type

RAID 0, RAID 1, RAID 5, RAID 10

Number of array

mber of

virtual disk 8

External interface

Network

interface 1,RJ-45, 10 /100 /1000 Mbps adaptive Ethernet interface

Serial interface

1 RS-232 interface (for parameters configuration, maintenance ,

transparent channel);

1 RS-485 interface (for PTZ control);

1 RS-485 keyboard interface (for special keyboard control)

USB interface 2, USB 2.0

Alarm in 16

Alarmout 4

General

Power

supply 100 ~ 240 VAC, 6.3 A, 50 ~ 60 Hz

Consumption ≤20 W(without hard disk or DVD-R/W)

Working

temperature -10℃~ +55℃

Working

humidity 10% ~ 90%

Chassis 19-inch rack-mounted 2U chassis

Dimensions

(W × D × H) 450 × 450 × 95 mm

Weight ≤8 kg ( without hard diskor DVD-R/W )

DS-9500 SeriesNVR Quick Operation Guide

HDD Storage Calculation Chart

Thefollowing chart showsan estimation of storage space used based on recording atone channel for an hour at a

fixed bit rate.

Bit Rate Storage Used

96K 42M

128K 56M

160K 70M

192K 84M

224K 98M

256K 112M

320K 140M

384K 168M

448K 196M

512K 225M

640K 281M

768K 337M

896K 393M

1024K 450M

1280K 562M

1536K 675M

1792K 787M

2048K 900M

Note: Please note that supplied values for storage space used is just for reference. Storage space used is

estimated byformulas and mayhavesome deviation from actual value.

DS-9500 SeriesNVR Quick Operation Guide

Basic Operation

Starting and Shutting Down Your NVR

Startup

Apply power to the unit and the POWER LED indicator on the front panelwill light in green, which indicates the

unit is powered on.

Note: DS-9500 series NVR do not provide local output, when the POWER and LINK LED indicators light

normally, it indicates the unit has been successfully started and connected to network.

Shutdown

Unplug the power cord to shut down the unit. It is not recommended to directly shut down the unit when it is in

recording.

Note: It is recommended that an Uninterruptible Power Supply (UPS) be used so as to ensure the unit to work

with high stability and security.

Access to DS-9500 by Client Software

Click “Start””All Programs”“iVMS-4000(v2.0)” to start the client software. After successful login, user can

enter the following main interface of the client software.

If the SADP software has been installed on PC, user can use it to automatically search and add the online devices

within the same local area network. Click Online Devicesbutton on the Add Device interface, and the system will

automatically search the onlinedevices.

The devices found will be listed on the panel with detail information.

Otros manuales para DS-9500 Series NVR

Tabla de contenidos

Otros manuales de DVR de HIK VISION

HIK VISION

HIK VISION DS-9000HFI-ST Manual de usuario

HIK VISION

HIK VISION DS-MP5 Series Manual de usuario

HIK VISION

HIK VISION DS-7100HWI-SL Series Manual de usuario

HIK VISION

HIK VISION DS-9600NI-I16 Series Manual de usuario

HIK VISION

HIK VISION DS-9000-ST Manual de usuario

HIK VISION

HIK VISION 9100HFI-ST Series Manual de usuario

HIK VISION

HIK VISION DS-7104NI-K1/W/M(C) Manual de usuario

HIK VISION

HIK VISION DS-7204HVI-S Series Manual de usuario

HIK VISION

HIK VISION DS-7200-SH Manual de usuario

HIK VISION

HIK VISION DS-8104AHQLI-K4 Manual de usuario

HIK VISION

HIK VISION DS-9204/08/16HWI-ST Manual de usuario

HIK VISION

HIK VISION DS-8100HMI-STM Manual de usuario

HIK VISION

HIK VISION DS-7200HVI-ST Series Guía del usuario

HIK VISION

HIK VISION DS-B116HCI-ST Manual de usuario

HIK VISION

HIK VISION DS-7300HI Series Guía del usuario

HIK VISION

HIK VISION DS-76 NI-I2/P Series Manual de usuario

HIK VISION

HIK VISION DS-7224HFI-ST Manual de usuario

HIK VISION

HIK VISION DS-8100HMFI-TH Series Manual de usuario

HIK VISION

HIK VISION DS-7300HI Series Manual de usuario

HIK VISION

HIK VISION UD.6L0202D1962A01 Manual de usuario

HIK VISION

HIK VISION DS-8100-S Series Manual de usuario

HIK VISION

HIK VISION DS-7108HI series Manual de usuario

HIK VISION

HIK VISION DS-MP5504 Series Manual de usuario

HIK VISION

HIK VISION DS-96 NI-ST Series Manual de usuario

Manuales populares de DVR de otras marcas

FLIR

FLIR M3100E Series Manual de usuario

VTRACKPRO

VTRACKPRO FPRO300 Manual de usuario

Swann

Swann NVR-7085 models Manual de usuario

XtendLan

XtendLan DVR-1670C Manual de usuario

urmet domus

urmet domus 1093/004AHD Manual de usuario

Holux

Holux M1 Manual de usuario

CMOS DOTCOM

CMOS DOTCOM ANX-1670 Manual de usuario

Whistler

Whistler D16VRS Manual de usuario

Defender Security

Defender Security 82-20235 Manual de usuario

MISUMI

MISUMI MP-WF100M Manual de usuario

Speco

Speco D8HU Manual de usuario

UST

UST DDR-E04AA Instrucciones de uso

Consolidated

Consolidated Digital Video Recorder Manual de usuario

Mace

Mace DVR0404RW Guía de inicio rápido

RCA

RCA RTD315W Manual de usuario

FSM

FSM Colibri Grande PRO Manual de usuario

Hauppauge

Hauppauge HD PVR 2 Manual de usuario

Identivision

Identivision ICR-PH161i PIONEER Manual de usuario